In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89f ("mlxsw: spectrum_router: Provide offload indication using nexthop flags")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c457 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
BUG: sleeping function called from invalid context
in_atomic(): 0, irqs_disabled(): 0, pid: 5762, name: ip
Preemption disabled at:
[<ffffff9d49043564>] debug_object_active_state+0xa4/0x16c
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
PC is at ___might_sleep+0x13c/0x180
LR is at ___might_sleep+0x17c/0x180
[<ffffff9d48ce0924>] ___might_sleep+0x13c/0x180
[<ffffff9d48ce09c0>] __might_sleep+0x58/0x8c
[<ffffff9d49d6253c>] mutex_lock+0x2c/0x48
[<ffffff9d48ed4840>] kernfs_remove_by_name_ns+0x48/0xa8
[<ffffff9d48ed6ec8>] sysfs_remove_link+0x30/0x58
[<ffffff9d49b05840>] __netdev_adjacent_dev_remove+0x14c/0x1e0
[<ffffff9d49b05914>] __netdev_adjacent_dev_unlink_lists+0x40/0x68
[<ffffff9d49b08820>] netdev_upper_dev_unlink+0xb4/0x1fc
[<ffffff9d494a29f0>] rmnet_dev_walk_unreg+0x6c/0xc8
[<ffffff9d49b00b40>] netdev_walk_all_lower_dev_rcu+0x58/0xb4
[<ffffff9d494a30fc>] rmnet_config_notify_cb+0xf4/0x134
[<ffffff9d48cd21b4>] raw_notifier_call_chain+0x58/0x78
[<ffffff9d49b028a4>] call_netdevice_notifiers_info+0x48/0x78
[<ffffff9d49b0b568>] rollback_registered_many+0x230/0x3c8
[<ffffff9d49b0b738>] unregister_netdevice_many+0x38/0x94
[<ffffff9d49b1e110>] rtnl_delete_link+0x58/0x88
[<ffffff9d49b201dc>] rtnl_dellink+0xbc/0x1cc
[<ffffff9d49b2355c>] rtnetlink_rcv_msg+0xb0/0x244
[<ffffff9d49b5230c>] netlink_rcv_skb+0xb4/0xdc
[<ffffff9d49b204f4>] rtnetlink_rcv+0x34/0x44
[<ffffff9d49b51af0>] netlink_unicast+0x1ec/0x294
[<ffffff9d49b51fdc>] netlink_sendmsg+0x320/0x390
[<ffffff9d49ae6858>] sock_sendmsg+0x54/0x60
[<ffffff9d49ae6f94>] ___sys_sendmsg+0x298/0x2b0
[<ffffff9d49ae98f8>] SyS_sendmsg+0xb4/0xf0
[<ffffff9d48c83770>] el0_svc_naked+0x24/0x28
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
<Mark Rutland reported>
While fuzzing arm64 v4.16-rc1 with Syzkaller, I've been hitting a
misaligned atomic in __skb_clone:
atomic_inc(&(skb_shinfo(skb)->dataref));
where dataref doesn't have the required natural alignment, and the
atomic operation faults. e.g. i often see it aligned to a single
byte boundary rather than a four byte boundary.
AFAICT, the skb_shared_info is misaligned at the instant it's
allocated in __napi_alloc_skb() __napi_alloc_skb()
</end of report>
Problem is caused by tun_napi_alloc_frags() using
napi_alloc_frag() with user provided seg sizes,
leading to other users of this API getting unaligned
page fragments.
Since we would like to not necessarily add paddings or alignments to
the frags that tun_napi_alloc_frags() attaches to the skb, switch to
another page frag allocator.
As a bonus skb_page_frag_refill() can use GFP_KERNEL allocations,
meaning that we can not deplete memory reserves as easily.
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794c ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set correct size of the CIM LA dump for T6.
Fixes: 27887bc7cb ("cxgb4: collect hardware LA dumps")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free pf 0-3 resources, commit baf5086840 ("cxgb4:
restructure VF mgmt code") erroneously removed the
code which frees the pf 0-3 resources, causing the
probe of pf 0-3 to fail in case of driver reload.
Fixes: baf5086840 ("cxgb4: restructure VF mgmt code")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device close or reset, there were some cases of outstanding
RX socket buffers not being freed. Include a function similar to the
one that already exists to clean TX socket buffers in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a RX buffer is returned to the client driver with an error, free the
corresponding socket buffer before continuing.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This memory is allocated during initialization but never freed,
so do that now.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device bringup, the driver exchanges login buffers with
firmware. These buffers contain information such number of TX
and RX queues alloted to the device, RX buffer size, etc. These
buffers weren't being properly freed on device reset or close.
We can free the buffer we send to firmware as soon as we get
a response. There is information in the response buffer that
the driver needs for normal operation so retain it until the
next reset or removal.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pushes back setting the carrier on until the end of the reset
code. This resolves a bug where a watchdog timer was detecting
that a TX queue had stalled before the adapter reset was complete.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit aa136d0c82.
As I previously[1] pointed out this implementation of XDP_REDIRECT is
wrong. XDP_REDIRECT is a facility that must work between different
NIC drivers. Another NIC driver can call ndo_xdp_xmit/nicvf_xdp_xmit,
but your driver patch assumes payload data (at top of page) will
contain a queue index and a DMA addr, this is not true and worse will
likely contain garbage.
Given you have not fixed this in due time (just reached v4.16-rc1),
the only option I see is a revert.
[1] http://lkml.kernel.org/r/20171211130902.482513d3@redhat.com
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Christina Jacob <cjacob@caviumnetworks.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Fixes: aa136d0c82 ("net: thunderx: Add support for xdp redirect")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlxsw_sp_fib_create() and mlxsw_sp_mr_table_create()
use ERR_PTR macro to propagate int err through return of a pointer,
the return value is not NULL in case of failure. So if one
of the calls fails, one of vr->fib4, vr->fib6 or vr->mr4_table
is not NULL and mlxsw_sp_vr_is_used wrongly assumes
that vr is in use which leads to crash like following one:
[ 1293.949291] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c9
[ 1293.952729] IP: mlxsw_sp_mr_table_flush+0x15/0x70 [mlxsw_spectrum]
Fix this by using local variables to hold the pointers and set vr->*
only in case everything went fine.
Fixes: 76610ebbde ("mlxsw: spectrum_router: Refactor virtual router handling")
Fixes: a3d9bc506d ("mlxsw: spectrum_router: Extend virtual routers with IPv6 support")
Fixes: d42b0965b1 ("mlxsw: spectrum_router: Add multicast routes notification handling functionality")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent a kernel panic on reboot if ptp_clock is NULL by checking
the ptp pointer before using it.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Fixes: 8c56df372b ("net: add support for Cavium PTP coprocessor")
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The control channel calls registered callbacks when control messages
such as XDomain protocol messages are received. The control channel
handling is done in a worker running on system workqueue which means the
networking driver can't run tear down flow which includes sending
disconnect request and waiting for a reply in the same worker. Otherwise
reply is never received (as the work is already running) and the
operation times out.
To fix this run disconnect ThunderboltIP flow asynchronously once
ThunderboltIP logout message is received.
Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When suspending to mem or disk the Thunderbolt controller typically goes
down as well tearing down the connection automatically. However, when
suspend to idle is used this does not happen so we need to make sure the
connection is properly disconnected before it can be re-established
during resume.
Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the SH-ETH device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commits 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") and 744dddcae8 ("clk:
renesas: mstp: Keep wakeup sources active during system suspend"), this
workaround is no longer needed. Hence remove all explicit clock
handling to keep the device active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the EtherAVB device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commit 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") , this workaround is no longer
needed. Hence remove all explicit clock handling to keep the device
active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcing a specific link mode, the PHY driver must clear the
existing speed and duplex bits in BMCR while preserving some other
control bits. This logic was accidentally inverted with the introduction
of phy_modify().
Fixes: fea23fb591 ("net: phy: convert read-modify-write to phy_modify()")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.
For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.
Improve code readability by removing this redundant code.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit 0a764db103 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit 0a764db103 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating RX or TX buffer pools, the driver needs to provide a
unique mapping ID to firmware for each pool. This value is assigned
using a counter which is incremented after a new pool is created. The
ID can be an integer ranging from 1-255. When migrating to a device
that requests a different number of queues, this value was not being
reset properly. As a result, after enough migrations, the counter
exceeded the upper bound and pool creation failed. This is fixed by
resetting the counter to one in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJafa95AAoJELDendYovxMvz8oH+QGgM0ZN0YfJa2JuR/RAlYyn
3OfSlMbGOjlmT74C1Rcx+SHNbbxUunoAx70UnvLbgtzbYyX08yVNsfNFesrarAkr
dkBBsAdLLzZYOoKnSKHWGl8Cf26F5eJbLo1FSSNYzmCaz0oD+geOqIWnOQMHkuUW
Rv6En9SjgzrE6dvzQ/LNtpjqFnSwJ+cD8ZkI21YXyDmZ3/xvZ9h8ID5vrzlP4wVH
gENxAMxn9w0nlbtHLvc2KGbVOUTSsA1LxbjDqzBEIGqgKmZVdt6d1J0KfO3eM6ej
9JuPcRt34HFPifuwI6xgtcKJjEr7QptIiDiSVvifXMvQnqfGc2b+qOFLhY6XwOU=
=+zOt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Only five small fixes for issues when running under Xen"
* tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix {set,clear}_foreign_p2m_mapping on autotranslating guests
pvcalls-back: do not return error on inet_accept EAGAIN
xen-netfront: Fix race between device setup and open
xen/grant-table: Use put_page instead of free_page
x86/xen: init %gs very early to avoid page faults with stack protector
This condition wasn't adjusted when PHY_IGNORE_INTERRUPT (-2) was added
long ago. In case of PHY_IGNORE_INTERRUPT the MAC interrupt indicates
also PHY state changes and we should do what the symbol says.
Fixes: 84a527a41f ("net: phylib: fix interrupts re-enablement in phy_start")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cavium thunder nicvf driver supports rx/tx rings of up to 65536 entries per.
The number of entires are stored in the q_len member of struct q_desc_mem. The
problem is that q_len being a u16, results in 65536 becoming 0.
In getting pointers to descriptors in the rings, the driver uses q_len minus 1
as a mask after incrementing the pointer, in order to go back to the beginning
and not go past the end of the ring.
With the q_len set to 0 the mask is no longer correct and the driver does go
beyond the end of the ring, causing various ills. Usually the first thing that
shows up is a "NETDEV WATCHDOG: enP2p1s0f1 (nicvf): transmit queue 7 timed out"
warning.
This patch remedies the problem by changing q_len to a u32.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJafIqwAAoJEG4XJFUm622bY1AH/jlWytWm+1/u8BTPFje0soxI
8ISNaTDVKu2s2DjCO7liuDGoQ/YqmYBYm0rc53RB0xI6hTSzdlD59gio9vUR6mF7
VQWhJ+L8H1mD0mJOwKP+VY/z0nkNK9QwOPZIO/sdspTp9LP207zSILabZEn58PEp
KKINTJagkBHb1zIm5Zl9jyin4PsOKRzWfp8z532Mw61S3+m8CbsKrRXnCB++gNAn
71a5ScPScsW/ROnJV9clx6CEsme5irFDz9qcknfz8se9do9uj+0kgkxFWGB+gnRl
2Mz3EIVhkEaZ4IMVXlv6yhan4bfkpsbPavw/hO2iHbLfZNpXrWEM+zIoSzOmOoc=
=BJaf
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While handling a driver reset we get a H_CLOSED return trying
to send a CRQ event. When this occurs we need to queue up another
reset attempt. Without doing this we see instances where the driver
is left in a closed state because the reset failed and there is no
further attempts to reset the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using devmap to redirect packets between interfaces,
xdp_do_flush() is usually a must to flush any batched
packets. Unfortunately this is missed in current tuntap
implementation.
Unlike most hardware driver which did XDP inside NAPI loop and call
xdp_do_flush() at then end of each round of poll. TAP did it in the
context of process e.g tun_get_user(). So fix this by count the
pending redirected packets and flush when it exceeds NAPI_POLL_WEIGHT
or MSG_MORE was cleared by sendmsg() caller.
With this fix, xdp_redirect_map works again between two TAPs.
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.16. Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
DKMS and similar out-of-tree module replacement services use
module version to make sure the out-of-tree software is not
older than the module shipped with the kernel. We use the
kernel version in ethtool -i output, put it into MODULE_VERSION
as well.
Reported-by: Jan Gutter <jan.gutter@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most FWs limit the number of TSO segments a frame can produce
to 64. This is for fairness and efficiency (of FW datapath)
reasons. If a frame with larger number of segments is submitted
the FW will drop it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All netdevs which can accept TC offloads must implement
.ndo_set_features(). nfp_reprs currently do not do that, which
means hw-tc-offload can be turned on and off even when offloads
are active.
Whether the offloads are active is really a question to nfp_ports,
so remove the per-app tc_busy callback indirection thing, and
simply count the number of offloaded items in nfp_port structure.
Fixes: 8a2768732a ("nfp: provide infrastructure for offloading flower based TC filters")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_port is a structure which represents an ASIC port, both
PCIe vNIC (on a PF or a VF) or the external MAC port. vNIC
netdev (struct nfp_net) and pure representor netdev (struct
nfp_repr) both have a pointer to this structure. nfp_reprs
always have a port associated. nfp_nets, however, only represent
a device port in legacy mode, where they are considered the
MAC port. In switchdev mode they are just the CPU's side of
the PCIe link.
By definition TC offloads only apply to device ports. Don't
set the flag on vNICs without a port (i.e. in switchdev mode).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming changes will require all netdevs supporting TC offloads
to have a full struct nfp_port. Require those for BPF offload.
The operation without management FW reporting information about
Ethernet ports is something we only support for very old and very
basic NIC firmwares anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Immed relocation is missing a shift which means for larger
offsets the lower and higher part of the address would be
ORed together.
Fixes: ce4ebfd859 ("nfp: bpf: add helpers for updating immediate instructions")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It was discovered that simple program which indefinitely sends 200b UDP
packets and runs on TI AM574x SoC (SMP) under RT Kernel triggers network
watchdog timeout in TI CPSW driver (<6 hours run). The network watchdog
timeout is triggered due to race between cpsw_ndo_start_xmit() and
cpsw_tx_handler() [NAPI]
cpsw_ndo_start_xmit()
if (unlikely(!cpdma_check_free_tx_desc(txch))) {
txq = netdev_get_tx_queue(ndev, q_idx);
netif_tx_stop_queue(txq);
^^ as per [1] barier has to be used after set_bit() otherwise new value
might not be visible to other cpus
}
cpsw_tx_handler()
if (unlikely(netif_tx_queue_stopped(txq)))
netif_tx_wake_queue(txq);
and when it happens ndev TX queue became disabled forever while driver's HW
TX queue is empty.
Fix this, by adding smp_mb__after_atomic() after netif_tx_stop_queue()
calls and double check for free TX descriptors after stopping ndev TX queue
- if there are free TX descriptors wake up ndev TX queue.
[1] https://www.kernel.org/doc/html/latest/core-api/atomic_ops.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will guard against a double free in the case that the
buffers were previously freed at some other time, such as during
a device reset. It resolves a kernel oops that occurred when changing
the VNIC device's MTU.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At some point, a check was added to exit the polling routine during resets.
This makes sense for most reset conditions, but for a non-fatal error, we
expect the polling routine to continue running to properly clean up the rx
queues. This patch checks if we are performing a non-fatal reset and if we
are, continues normal polling operation.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the appropriate SPDX license tags to the Sun network drivers
as outlined in Documentation/process/license-rules.rst.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
