Instead of harcoding keycodes specifications in the Armada 370/XP
boards, use the <dt-bindings/input/input.h> header file and its
keycode definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of harcoding 0 and 1 for the gpio specifications in the Armada
370/XP boards, use the <dt-bindings/gpio/gpio.h> header file and its
GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW definitions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Generally, power LEDs should indicate when power is applied, and go out
once power is removed. _Not_ annoy the developer with migraine-inducing
blinking reminicent of some badly animated television series designed to
sell sugar to children.
On a more serious note, most of these OS-specific properties aren't
necessary and should be removed. I left two that are legitimately tying
disk LEDs to disk activity. Other than that, we keep the state the
bootloader left them in until userspace changes the state via sysfs.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of internal registers, placing it directly
below the mbus. This is a more accurate representation of the
hardware.
Moving the PCIe nodes, we now need to introduce an extra cell to
encode the window target ID and attribute. Since this depends on
the PCIe port, we split the ranges translation entries, to correspond
to each MBus window.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that mbus has been added to the device tree, it's possible to
move the DeviceBus out of internal registers, placing it directly
below the mbus. This is a more accurate representation of the hardware.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to access the SoC BootROM, we need to declare a mapping
(through a ranges property). The mbus driver will use this property
to allocate a suitable address decoding window.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370/XP SoC family has a completely configurable address
space handled by the MBus controller.
This patch introduces the device tree layout of MBus, making the
'soc' node as mbus-compatible.
Since every peripheral/controller is a child of this 'soc' node,
this makes all of them sit behind the mbus, thus describing the
hardware accurately.
A translation entry has been added for the internal-regs mapping.
This can't be done in the common armada-370-xp.dtsi because A370
and AXP have different addressing width.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvwUEAAoJEFBXWFqHsHzOZXgH/jYs9okBIb6UtYegmdGUinCD
VHJJT+RT8ceosMjBt+aBfpKplUG1X3OOoWbpU7Uv5JKNfY+0QbYTr4bdSE0YTF19
/ml5lCLLqW1MouErxIIe9yFrs4ZhZLLuW0Uy+ze7XVO/VPUlmJWYGU4D5gLcN+SH
aDdwAfe0SEydxWKp5euh6O2qPuuOro5/kUOPvYs6xaJj3marWkD9M6YyhaWvaFwF
2iUWzSd6dGabHRYwG2r38IlKMo6xncnu3b1NPifVMiPtiHFJ8t0SyTEGmpq19G+x
G6q0TneOUVIgH0PN4YQoCGOR6oAB52Z/dVTVlGx6LE6w9Q95wI3XNHltP5U+bF0=
=Oeyn
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
mxs device tree changes for 3.11:
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
* tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree
ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree
ARM: cfa10049: Switch the chip select pin of the LCD controller
ARM: cfa10036: Add USB0 OTG port
ARM: dts: apf28dev: Add touchscreen support for APF28dev
ARM: mxs: Fix UARTs on M28EVK
ARM: cfa10036: dt: Change i2c0 clock frequency
ARM: dts: cfa10036: Change the OLED display to SSD1306
ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
ARM: mxs: Use soc bus infrastructure
ARM: dts: mx28: Adjust the digctl compatible string
ARM: mxs: Remove init_irq declaration in machine description
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.
This commit fixes those platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- mvebu
- enable two usb interfaces on Armada XP-GP
- kirkwood
- move pinmux configs to their individual devices
- group the pinmux configs on OpenBlocks A6
- add the Init button for the OpenBlocks A6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPZAAAoJEAi3KVZQDZAe/6AIAIvtbKlec9up7/QoIzM7varY
Qfb7OU6EQYnNmTiY+n/y2REz03mUC/cnrvRZ0YD31i5WwHZWGQiz1R692Tt1e07A
Cugl75yLuOFnsSKqkvRy0Km2QF35Irk22stBRP85csGu/LjjSqr0gXDsJ2++oQfZ
ssco7I5MsTEFJDpeVAB5jFaFm+hs+uM8/WsUf7l7qjyImqkz1WZPZfkgevWm3UjH
Mz2Ur2Sbapq5gU+/h8GdzWJdCuSM0wmZ3TKGOk2BCbMFBFSr72tPUgVDwYge7Ae4
5lPoeHg00o8TM6kpf5OBGW8kq6oMij33e7YjVpAp/YdsAmyua1gFCFikW3APuJU=
=SWgl
-----END PGP SIGNATURE-----
Merge tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux into next/dt
From jason Cooper, mvebu dt changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux: (27 commits)
arm: kirkwood: openblocks-a6: add support for Init button
arm: kirkwood: openblocks-a6: group pinmux configurations
arm: kirkwood: ts219: move pinmux configs to the right devices
arm: kirkwood: topkick: move pinmux configs to the right devices
arm: kirkwood: openblocks_a6: move pinmux configs to the right devices
arm: kirkwood: nsa310: move pinmux configs to the right devices
arm: kirkwood: readynas: move pinmux configs to the right devices
arm: kirkwood: mplcec4: move pinmux configs to the right devices
arm: kirkwood: buffalo linkstation: move pinmux configs to the right devices
arm: kirkwood: keymile: move pinmux configs to the right devices
arm: kirkwood: ns2: move pinmux configs to the right devices
arm: kirkwood: iomega ix2-200: move pinmux configs to the right devices
arm: kirkwood: iconnect: move pinmux configs to the right devices
arm: kirkwood: iconnect: give meaningful names to pinmux configs
arm: kirkwood: ib62x0: move pinmux configs to the right devices
arm: kirkwood: guruplug: move pinmux configs to the right devices
arm: kirkwood: goflexnet: move pinmux configs to the right devices
arm: kirkwood: dreamplug: move pinmux configs to the right devices
arm: kirkwood: dockstar: move pinmux configs to the right devices
arm: kirkwood: dlink dns: move pinmux configs to the right devices
...
Besides the two "classic" USB interfaces with normal USB ports on the
front side, the PlatHome OpenBlocks AX3 uses the third USB interface
of the Marvell SoC in the mini-PCIe connector. This allows certain
mini-PCIe cards to expose parts of their functionality as a USB
peripheral.
This commit enables this third USB interface in the OpenBlocks AX3
Device Tree, and also adds comments on top of the two other USB
interfaces so that the Device Tree makes it clear which USB interface
at the SoC level matches which USB interface visible on the board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the latest device tree reorganization which introduced the
'internal-reg' node, now the only region translated is the internal register's.
This makes the description of the hardware incomplete, for it lacks the
Device Bus childs address space.
In order to fix this, it's required to add a 'ranges' entry with a suitable
address space to map Device Bus childs, on a per-board basis.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to be able to use more than 4GB of RAM when the LPAE is
activated, the dts must be converted in 64 bits.
Only Armada XP is LPAE capable, but as it shares a common dtsi file
with Armada 370, then the common file include the skeleton64. Thanks
to the use of the overload capability of the device tree format,
armada-370 include the 32 bit skeleton and all the armada 370 based
dts can remain the same.
This was heavily based on the work of Lior Amsalem.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Introduce a 'internal-regs' subnode, under which all devices are
moved. This is not really needed for now, but will be for the
mvebu-mbus driver. This generates a lot of code movement since it's
indenting by one more tab all the devices. So it was a good
opportunity to fix all the bad indentation.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This conversion will allow to keep 32 bits addresses for the internal
registers whereas the memory of the system will be 64 bits.
Later it will also ease the move of the mvebu-mbus driver to the
device tree support.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The PlatHome OpenBlocks AX3-4 has an internal mini-PCIe slot that can
be used to plug mini-PCIe devices. We therefore enable the PCIe
interface that corresponds to this slot.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Plat'home Openblocks AX3 has a 128 MiB NOR flash device connected
to the Device Bus. This commit adds the device tree node to support this device.
The SoC supports a flexible and dynamic decoding window allocation scheme;
but since this feature is still not implemented we need to specify the window
base address in the device tree node itself.
This base address has been selected in a completely arbitrary fashion.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch enables SATA support on the OpenBlocks AX3-4. It has one
internal SATA port, and an external eSATA port.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The OpenBlocks AX3-4 has a Seiko Instruments S-35390A as the RTC
controller. This patch enables this RTC device in the OpenBlocks
AX3-4 Device Tree.
[Thomas Petazzoni: updated with other OpenBlocks changes, rephrased
commit log.]
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The OpenBlocks AX3-4 board, based on the Armada XP SoC, has an I2C
bus. This patch enables this bus and sets the clock frequency of the
bus.
[Thomas Petazzoni: updated with other changes on OpenBlocks, rephrased
commit log.]
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The mvneta driver for the Marvell Armada 370/XP Ethernet devices has
gained proper clock framework integration, and the corresponding
Device Tree nodes now have a correct 'clocks' pointer.
The 'clock-frequency' properties in the various .dts files for Armada
370/XP boards have therefore become useless.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The PlatHome OpenBlocks AX3-4 platform has 4 Ethernet ports, connected
to a single quad-port PHY through SGMII.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This platform, available in Japan from PlatHome, has a dual-core
Armada XP, the MV78260. For now, only the two serial ports and the
three front LEDs are supported. Support for SMP, network, SATA, USB
and other peripherals will be added as drivers for them become
available for Armada XP in mainline.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
This is 3.8 material.
Changes since v2:
* Renamed the .dts file to armada-xp-openblocks-ax3-4.dts
* Removed the compatible string from armada-370-xp.c (which now only
lists the common SoC compatible string)
Changes since v1:
* Renamed the board to OpenBlocks AX3-4, since there is a variant
called AX3-2 which has less RAM, and no mini PCIe port. Requested
by Andrew Lunn.
* Fix the amount of memory to 3 GB. In fact, the board has 1 GB
soldered, and 2 GB in a SODIMM slot (which is therefore
removable). But as the board is delivered as is, we'll assume it
has 3 GB of memory by default.
