platform_get_irq() returns an error code, but the spi-bcm63xx driver
ignores it and always returns -ENXIO. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the checkpatch.pl warnings on the driver
file.
Signed-off-by: Aravind Thokala <aravind.thk@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix compilation by renaming argument dev to spi as expected by the code.
Fixes the following error:
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_max_length’:
drivers/spi/spi-bcm63xx.c:434:50: error: ‘spi’ undeclared (first use in this function)
struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
^~~
Fixes: 0135c03df9 ("spi/bcm63xx: make spi subsystem aware of message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add required binding support to probe through device tree.
Use the compatible instead of the resource size for identifiying the
block type, and allow reducing the number of cs lines through OF.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm63xx SPI controller does not allow manual control of the CS
lines and will toggle it automatically before and after sending data,
so we are limited to messages that fit in the FIFO buffer. Since the CS
lines aren't available as GPIOs either, we will need to make slave
drivers aware of this limitation so they can handle them accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With a 64-bit resource_size_t, we get a build warning on bcm63xx_spi_probe:
drivers/spi/spi-bcm63xx.c:565:16: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
As we are printing a resource, we can just use the %pr format
specifier that pretty-prints the address and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_setup_transfer’:
drivers/spi/spi-bcm63xx.c:207: warning: ‘clk_cfg’ may be used uninitialized in this function
While this is a false positive, it can easily be avoided by selecting
the default clock configuration first.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all register definitions and structs into the driver. This allows
us dropping the platform_data struct and drop any arch specific
includes. Make use of different device names to identify the version of
the block we have.
Since we now have full control over the message width, we can drop the
size check, which was broken anyway, since it never set ret to any error
code.
Also since we now have no arch depedendent resources, we can now allow
compiling it for any arch, hidden behind COMPILE_TEST.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the message control word parameters part of the register offsets
array so we have them all in one struct.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct guard CONFIG_CPU_BIG_ENDIAN and the *be accessors to
follow native endianness on big endian systems.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace all bcm_read* with (io)read. Due to this block following
system endianness, make sure we match that.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass 0 as the spi bus number, so we might as well hard code
it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass 8 for the number of chip selects, so we can as well
hardcode it to this number.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following warning:
drivers/spi/spi-bcm63xx.c:125:5: warning: unused variable 'rx_tail' [-Wunused-variable]
u8 rx_tail;
^
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Calling init_completion() once is enough.
For the rest of the iterations, call reinit_completion() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory, otherwise we will
leak a reference to master. Fix by removing the unnecessary
spi_master_get() call.
Fixes: 247263dba2 ('spi: bcm63xx: use devm_spi_register_master()')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the correct symbol to guard the callbacks and use appropriate defines
for setting up the ops struct.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure we notice if the clock cannot be enabled for any reason and pass
the error down.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The rx_tail register is only 8 bit wide, so it will wrap around
after 256 read bytes. This makes it rather meaningless, so drop any
usage of it to not treat reads over 256 as failed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The spi command must include the full message length including any
prepended writes, else transfers larger than 256 bytes will be
incomplete.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory, otherwise we will
leak a reference to master. Fix by removing the unnecessary
spi_master_get() call.
Fixes: 247263dba2 ('spi: bcm63xx: use devm_spi_register_master()')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler,
and remove a duplicate put.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use dev_get_drvdata() instead of platform_get_drvdata(to_platform_device(dev)).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
speed_hz is a write only member, so we can safely remove it and its
generation. Also fixes the missing clk_put after getting the periph
clock.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devm_ioremap_resource() which provides its own error messages.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
bcm63xx_spi_setup_transfer is called from only one place, and that has
t always set, to hz will always be t->speed_hz - just use it directly in
the two places instead of moving it in a local variable.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It only does one check, so just do the check directly in the caller.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The check would belong in bcm63xx_spi_setup if the spi subsystem
weren't already doing the check for us, so just drop it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
bcm63xx_spi_check_transfer is only called from one place that has
t always set, so directly check the transfer's bits_per_word.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of fixing up the bits_per_word (which the spi subsystem already
does for us), check it for supported values.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is only written, but never read.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spi subsystem already provides this info in a more extensive
debug print except for the nsecs/bit - which wasn't calculated anyway
and fixed to 0.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
