Add SPI Serial Interface Mode (SIM) register information
to STM pressure framework
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information to
LIS3MDL magn sensor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
to STM gyroscope framework
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2DW12 accelerometer in
st_accel framework
http://www.st.com/resource/en/datasheet/lis2dw12.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New devices (e.g. LIS2DW12) enable all axis by default and do not export
that capability in register map. Check if the enable_axis register
address has been declared in st_sensor_settings map in order to verify if
the driver needs to enable all sensor axis
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref. In other words, "full scale" means +/- 2^20.
This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).
The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).
Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS. Instead, CS is asserted
for 8 usec to start the conversion. After waiting for the duration of
the conversion, the result can be fetched. While waiting, control of
the bus is ceased so it may be used by a different device.
After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).
Optionally, the chips can be used in so-called "continuous conversion
mode": Conversions then take place continuously and the last result may
be fetched at any time without observing a delay. The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground. The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.
The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes. Calculate the word length on probe by rounding up the
resolution to full bytes. Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the ABI documentation, the shunt resistor value should be
specificied in Ohm. As this is also used/documented for the MAX9611,
use the same for the INA2xx driver.
This poses an ABI break for anyone actually altering the shunt value
through the sysfs interface, it does not alter the default value nor
a value set from the devicetree.
Minor change: Fix comment, 1mA is 10^-3A.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce FIFO ops data structure to contain FIFO related parameters
in order to properly support more devices in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move FIFO decimator info in st_lsm6dsx_sensor_settings list since
decimator registers are exported in register map just in
lsm6ds3/lsm6ds3h/lsm6dsl/lsm6dsm sensors and not in other compliant
devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate fifo mode and max fifo sample rate configuration.
That change will be necessary to reuse st_lsm6dsx_set_fifo_mode()
routine and to support more devices in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Express max fifo depth in ST_LSM6DSX_SAMPLE_SIZE instead of in bytes.
That change will be necessary to properly support more devices
in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the of_device_get_match_data() helper instead of open coding.
Note that the rcar-gyroadc driver is used with DT only, so there's
always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The rcar-gyroadc driver compiles fine on other platforms, hence increase
compile coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On 64-bit:
drivers/iio/adc/rcar-gyroadc.c: In function 'rcar_gyroadc_parse_subdevs':
drivers/iio/adc/rcar-gyroadc.c:352:15: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
childmode = (unsigned int)of_id->data;
^
Cast the pointer to uintptr_t instead of unsigned int to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reported scale was only correct for the default settings of 100 ms
integration time and gain 1.
This aligns the reported scale with the behaviour of any other IIO driver
and the documented ABI, but may require userspace changes if someone uses
non-default settings.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of manually iterating the array of allowed gain values, use
find_closest. Storing the current gain setting avoids accessing the
hardware on each query.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of reading the value from the register on each query, store the
set value.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This improves code uniformity (range checks for als_gain are also done
in the setter). Also unmangle rounding and calculation of register value.
The calculated integration time it_ms is required in the next patch of
the series.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
KXTF9 has mostly compatible register layout to KXCJK accelerometer.
There is no motion direction interrupt support, but there is tap
direction detection instead (not implemented in this patch).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make sampling_frequency_avail per-type - like sampling_frequency is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation for KXTF9 support, make sampling_frequency_avail
attribute dynamic.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extract reporting of motion event direction from interrupt handler,
as it is not supported by KXTF9.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix INT_CTRL1 bit names to match register name and add names
for INT_SRC1 bits.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor ODR/WUF setting code in preparation of KXTF9 support.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'mma8452_read_thresh' and 'mma8452_write_thresh' functions
does more than just read/write threshold values.
They also handle IIO_EV_INFO_HIGH_PASS_FILTER_3DB and
IIO_EV_INFO_PERIOD therefore renaming to generic names.
Improves code readability, no impact on functionality.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch, forgetting to put a thermal-zones DT node would
result in the driver failing to probe.
It should be perfectly acceptable to have the driver probe even if no
thermal-zones DT is found. However, it shouldn't want to fail if the
thermal registering fail for any other reason (waiting for other drivers
for example) so check on ENODEV only.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver has a get_temp function used by the thermal framework that
uses pm functions.
However, the driver isn't registered in pm before it is registered in
thermal framework, resulting in the pm_resume not being called and thus
the IP not enabled.
When the IP is disabled, the raw temp value is always 0. With the
devices currently supported, it isn't a problem since with their
respective formula, they return a really cold SoC temperature which
isn't a problem for the thermal framework. But for future SoC that have
a different formula, it could return a critically hot temperature,
forcing the thermal framework to shutdown the board.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch provides an iio device driver for DS4422/DS4424 chips that support
two/four channel 7-bit Sink/Source Current DAC.
Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements have gone away.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
If an IIO device returns an error code for a read access via debugfs, it
is currently ignored by the IIO core (other than emitting an error
message). Instead, return this error code to user space, so upper layers
can detect it correctly.
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The serial interface can be reset by writing 32 consecutive 1s to the device.
'ret' was initialized correctly but its value was overwritten when
ad7793_check_platform_data() was called. Since a dedicated reset function
is present now, it should be used instead.
Fixes: 2edb769d24 ("iio:ad7793: Add support for the ad7798 and ad7799")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ctrl_reg register needs to be written after any write to
the humidity registers. The value written to the ctrl_reg register
does not necessarily need to change, but a write operation must
occur.
The regmap_update_bits functions will not write to a register
if the register value matches the value to be written. This saves
unnecessary bus operations. The change in this patch forces a bus
write during the chip_config operation by switching to
regmap_write_bits.
This will fix issues where the Humidity Sensor Oversampling bits
are not updated after initialization.
Signed-off-by: Colin Parker <colin.parker@aclima.io>
Acked-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
returns a signed voltage from mcp320x_adc_conversion() but neglects that
the caller interprets a negative return value as failure. Only mcp3301
(and the upcoming mcp3550/1/3) is affected as the other chips are
incapable of measuring negative voltages.
Fix and while at it, add mcp3301 to the list of supported chips at the
top of the file.
Fixes: f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
Cc: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver calls spi_get_drvdata() in its ->remove hook even though it
has never called spi_set_drvdata(). Stack trace for posterity:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
Internal error: Oops: 5 [#1] SMP ARM
[<8072f564>] (mutex_lock) from [<7f1400d0>] (iio_device_unregister+0x24/0x7c [industrialio])
[<7f1400d0>] (iio_device_unregister [industrialio]) from [<7f15e020>] (mcp320x_remove+0x20/0x30 [mcp320x])
[<7f15e020>] (mcp320x_remove [mcp320x]) from [<8055a8cc>] (spi_drv_remove+0x2c/0x44)
[<8055a8cc>] (spi_drv_remove) from [<805087bc>] (__device_release_driver+0x98/0x134)
[<805087bc>] (__device_release_driver) from [<80509180>] (driver_detach+0xdc/0xe0)
[<80509180>] (driver_detach) from [<8050823c>] (bus_remove_driver+0x5c/0xb0)
[<8050823c>] (bus_remove_driver) from [<80509ab0>] (driver_unregister+0x38/0x58)
[<80509ab0>] (driver_unregister) from [<7f15e69c>] (mcp320x_driver_exit+0x14/0x1c [mcp320x])
[<7f15e69c>] (mcp320x_driver_exit [mcp320x]) from [<801a78d0>] (SyS_delete_module+0x184/0x1d0)
[<801a78d0>] (SyS_delete_module) from [<80108100>] (ret_fast_syscall+0x0/0x1c)
Fixes: f5ce4a7a92 ("iio: adc: add driver for MCP3204/08 12-bit ADC")
Cc: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove rounding configuration since it is enabled by default for the
FIFO output registers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove Latched Interrupt configuration since it is enabled by default
for FIFO watermark interrupt
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit adds mt2712 compatible node.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update odr value in st_lsm6dsx_sensor data structure just in
st_lsm6dsx_write_raw() in order to avoid to set the same value
multiple times
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace 'unsigned' with 'unsigned int'
to improve code readability.
Issue found by checkpatch.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace symbolic permissions with octal permissions
to improve code readability.
Issue found by checkpatch.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a bad error check when counting 'st,adc-channels' array elements.
This is seen when all channels are in use simultaneously.
Fixes: 64ad7f643 ("iio: adc: stm32: introduce compatible data cfg")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Balance timer start routine that sets ARPE: clear it in stop routine.
This fixes a corner case, when timer is used successively as trigger
(with sampling_frequency start/stop routines), then as a counter
(with preset).
Fixes: 93fbe91b55 ("iio: Add STM32 timer trigger driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, setting preset value (ARR) will update directly 'Auto reload
value' only on 1st write access. But then, ARPE is set. This makes
ARR a shadow register. Preset value should be updated upon each
write request: ensure ARPE is 0. This fixes successive writes to
preset attribute.
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
