This patch cleans a arm-pmu node up for exynos4. Only exynos4412 series
boards have four pmu interrupts. Rest of exynos4 boards, except 4412, have only
two pmu interrupts. Thus, we can define two interrupts in the
exynos4.dtsi and extends the interrupts only exynos4412.dtsi.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Display domain is removed due to instability issues. Explaining
the problem below:
exynos_init_late triggers the pm_genpd_poweroff_unused which powers
off the unused power domains. This call hits before the trigger to
deferred probes.
DRM DP Panel defers the probe due to supply get failure. By the time,
deferred probe is scheduled again, Display Power Domain is powered
off by pm_genpd_poweroff_unused.
FIMD and DP drivers are accessing registers during Probe and Bind
callbacks. If display domain is enabled/disabled around register
accesses, display domain gets unstable and we are getting Power Domain
Disable fail notification. Increasing the Timeout also didn't help.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add MAX98090 audio codec, I2S interface and the sound complex
nodes to enable audio on Odroid-X2/U3 boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
TFLASH (SDHCI2 controller) uses internal card detect line, but it looks
that the driver fails to operate it properly. Use GPIO interrupt on
SD_CDn line for detecting SD card state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for simple GPIO-based button availabled on
Exynos4 based Odroid boards. All supported boards have POWER button,
which has been defined in exynos4412-odroid-common.dtsi. X/X2 boards
also have additional user-configurable button which has been mapped to
KEY_HOME. All defined keys have been marked as possible wakeup source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On Odroid U2/U3 BUCK8 is used for providing power to also to P3V3
source, which is also connected to LAN9730 chip's nRESET signal. To
reset lan chip on system reboot, the BUCK8 output should not be used in
'always on' mode. This change has no impact on X/X2 boards.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves some parts of exynos4412-odroidx.dts to common
exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and
U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz
instead of 1.4GHz), while U2/U3 differs from X2 by different way of
routing signals to host USB hub. It also lacks some hw modules not yet
supported by those dts files (i.e. LCD & touch panel).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Last megabyte of RAM is used by secure firmware and should not be accessed
by Linux kernel, so correct available memory size in DTS file.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds basic support for USB modules (host and device) on
OdroidX board.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[removed incorrect port@2 node]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for common hardware modules available on all
Exynos4412-based Odroid boards, which already have complete support in
mainline kernel. This includes secure firmware calls, watchdog, g2d and
fimc (mem2mem) multimedia accelerators.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds port sub-nodes to exynos4 ehci and ohci modules, which
are required by recently merged new exynos4 usb2 phy support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake. If we don't set it to anything then
the TPM will be reset. U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything. It will get pulled back high again during a
normal warm reset when it will default back to an input.
To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake. If we don't set it to anything then
the TPM will be reset. U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything. It will get pulled back high again during a
normal warm reset when it will default back to an input.
To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add sound-card name property to Snow/Peach-Pit/Peach-Pi boards.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
It's 1.6 GHz for the Cortex-A15.
Avoids warnings like "/cpus/cpu@0 missing clock-frequency property".
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Peach-pit and Peach-pi boards are almost similar, hence the DTS file
is also very similar. Sorting nodes in both these files will allow
us to figure out the difference easily.
All the node aliases are sorted in alphabetically increasing order.
There is no functional change with this patch.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Peach-pi board has MAX98091 audio codec connected on HSI2C-7 bus.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
3.16. They are simply fixes and code refactoring for the OMAP clock
drivers. The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=9/Iv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
This is a small follow-up to the larger ARM SoC updates merged
last week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code
that came in through Russell's ARM tree. This allows the keystone
platform to do cache-coherent DMA and to finally support all the
available physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten,
and there is a small bug fix to allow building the orion5x platform
again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AqkT
-----END PGP SIGNATURE-----
Merge tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull part two of ARM SoC updates from Arnd Bergmann:
"This is a small follow-up to the larger ARM SoC updates merged last
week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code that
came in through Russell's ARM tree. This allows the keystone platform
to do cache-coherent DMA and to finally support all the available
physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten, and
there is a small bug fix to allow building the orion5x platform again"
* tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: Drop use of meminfo since its not available anymore
ARM: orion5x: fix mvebu_mbus_dt_init call
ARM: configs: keystone: enable reset driver support
ARM: dts: keystone: update reset node to work with reset driver
ARM: keystone: remove redundant reset stuff
ARM: keystone: Update the dma offset for non-dt platform devices
ARM: keystone: Switch over to coherent memory address space
ARM: configs: keystone: add MTD_SPI_NOR (new dependency for M25P80)
ARM: configs: keystone: drop CONFIG_COMMON_CLK_DEBUG
Pull input updates from Dmitry Torokhov:
"A big update to the Atmel touchscreen driver, devm support for polled
input devices, several drivers have been converted to using managed
resources, and assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: synaptics - fix resolution for manually provided min/max
Input: atmel_mxt_ts - fix invalid return from mxt_get_bootloader_version
Input: max8997_haptic - add error handling for regulator and pwm
Input: elantech - don't set bit 1 of reg_10 when the no_hw_res quirk is set
Input: elantech - deal with clickpads reporting right button events
Input: edt-ft5x06 - fix an i2c write for M09 support
Input: omap-keypad - remove platform data support
ARM: OMAP2+: remove unused omap4-keypad file and code
Input: ab8500-ponkey - switch to using managed resources
Input: max8925_onkey - switch to using managed resources
Input: 88pm860x-ts - switch to using managed resources
Input: 88pm860x_onkey - switch to using managed resources
Input: intel-mid-touch - switch to using managed resources
Input: wacom - process outbound for newer Cintiqs
Input: wacom - set stylus_in_proximity when pen is in range
DTS: ARM: OMAP3-N900: Add tsc2005 support
Input: tsc2005 - add DT support
Input: add common DT binding for touchscreens
Input: jornada680_kbd - switch top using managed resources
Input: adp5520-keys - switch to using managed resources
...
Add OMAP DT data:
* omap5 display subsystem
* display data for omap5 uEVM board
* am43xx display subsystem
* display data for am43xx ePOS and GP boards (LCD only)
* display data for GTA04 board
* display data for overo board
* display data for duovero-parlor board
* display data for omap3 evm and ldp boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/UHU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-omap-dt-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP DT fbdev updates from Tomi Valkeinen:
"Here are display related device tree data changes for OMAP. They are
based on an already merged branch to satisfy the dependencies for the
dts file changes.
Add OMAP DT data:
- omap5 display subsystem
- display data for omap5 uEVM board
- am43xx display subsystem
- display data for am43xx ePOS and GP boards (LCD only)
- display data for GTA04 board
- display data for overo board
- display data for duovero-parlor board
- display data for omap3 evm and ldp boards"
* tag 'fbdev-omap-dt-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: omap5.dtsi: Add audio related parameters to hdmi node
ARM: omap4.dtsi: Add audio related parametes to hdmi node
ARM: dts: duovero-parlor: Add HDMI output
ARM: dts: overo: Add support for 3.5'' LCD output
ARM: dts: overo: Add support for 4.3'' LCD output
ARM: dts: overo: Add support for DVI output
ARM: dts: Add LCD panel sharp ls037v7dw01 support for omap3-evm and ldp
ARM: dts: omap3-gta04: Add display support
ARM: dts: omap5-uevm.dts: add display nodes
ARM: dts: omap5-uevm.dts: add tca6424a
ARM: dts: omap5.dtsi: add DSS nodes
ARM: dts: am43x-epos-evm: add LCD data
ARM: dts: am437x-gp-evm: add LCD data
ARM: dts: am4372.dtsi: add DSS information
driver additions and fixes. There are additions to the clock core code
for some of the basic types (e.g. the common divider type has some fixes
and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. ba0fae3 in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=2AAL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
Pull i2c updates from Wolfram Sang:
"I2C has the following updates for 3.16:
- major cleanups to the rcar and sh_mobile drivers
- removal of nuc900 driver which had a compile error for years
- usual bunch of driver updates, bugfixes and cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: pca954x: Fix compilation without CONFIG_GPIOLIB
i2c: mux: pca954x: Use the descriptor-based GPIO API
i2c: mpc: insert DR read in i2c_fixup()
i2c: bfin: turn to Resource-managed API in probe function
i2c: Make of_device_id array const
i2c: remove unnecessary OOM messages
i2c: designware-pci: Add Haswell PCI IDs
i2c: designware: Add runtime PM hooks
i2c: designware: Disable device on system suspend
i2c: nuc900: remove driver
i2c: imx: update i2c clock divider for each transaction
i2c: imx: fix the i2c bus hang issue when do repeat restart
i2c: rcar: update copyright and license information
i2c: rcar: janitorial cleanup after refactoring
i2c: rcar: reuse status bits as enable bits
i2c: rcar: remove spinlock
i2c: rcar: refactor status bit handling
i2c: rcar: refactor setting up msg
i2c: rcar: check bus free before first message
i2c: rcar: refactor irq state machine
...
OMAP5432, DRA75x and DRA72x have MPU DPLLs that need Duty Cycle
Correction(DCC) to operate safely at frequencies >= 1.4GHz.
Switch to "ti,omap5-mpu-dpll-clock" compatible property which provides
this support.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Pull ARM updates from Russell King:
- Major clean-up of the L2 cache support code. The existing mess was
becoming rather unmaintainable through all the additions that others
have done over time. This turns it into a much nicer structure, and
implements a few performance improvements as well.
- Clean up some of the CP15 control register tweaks for alignment
support, moving some code and data into alignment.c
- DMA properties for ARM, from Santosh and reviewed by DT people. This
adds DT properties to specify bus translations we can't discover
automatically, and to indicate whether devices are coherent.
- Hibernation support for ARM
- Make ftrace work with read-only text in modules
- add suspend support for PJ4B CPUs
- rework interrupt masking for undefined instruction handling, which
allows us to enable interrupts earlier in the handling of these
exceptions.
- support for big endian page tables
- fix stacktrace support to exclude stacktrace functions from the
trace, and add save_stack_trace_regs() implementation so that kprobes
can record stack traces.
- Add support for the Cortex-A17 CPU.
- Remove last vestiges of ARM710 support.
- Removal of ARM "meminfo" structure, finally converting us solely to
memblock to handle the early memory initialisation.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (142 commits)
ARM: ensure C page table setup code follows assembly code (part II)
ARM: ensure C page table setup code follows assembly code
ARM: consolidate last remaining open-coded alignment trap enable
ARM: remove global cr_no_alignment
ARM: remove CPU_CP15 conditional from alignment.c
ARM: remove unused adjust_cr() function
ARM: move "noalign" command line option to alignment.c
ARM: provide common method to clear bits in CPU control register
ARM: 8025/1: Get rid of meminfo
ARM: 8060/1: mm: allow sub-architectures to override PCI I/O memory type
ARM: 8066/1: correction for ARM patch 8031/2
ARM: 8049/1: ftrace/add save_stack_trace_regs() implementation
ARM: 8065/1: remove last use of CONFIG_CPU_ARM710
ARM: 8062/1: Modify ldrt fixup handler to re-execute the userspace instruction
ARM: 8047/1: rwsem: use asm-generic rwsem implementation
ARM: l2c: trial at enabling some Cortex-A9 optimisations
ARM: l2c: add warnings for stuff modifying aux_ctrl register values
ARM: l2c: print a warning with L2C-310 caches if the cache size is modified
ARM: l2c: remove old .set_debug method
ARM: l2c: kill L2X0_AUX_CTRL_MASK before anyone else makes use of this
...
Pull timer core updates from Thomas Gleixner:
"This time you get nothing really exciting:
- A huge update to the sh* clocksource drivers
- Support for two more ARM SoCs
- Removal of the deprecated setup_sched_clock() API
- The usual pile of fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
clocksource: Add Freescale FlexTimer Module (FTM) timer support
ARM: dts: vf610: Add Freescale FlexTimer Module timer node.
clocksource: ftm: Add FlexTimer Module (FTM) Timer devicetree Documentation
clocksource: sh_tmu: Remove unnecessary OOM messages
clocksource: sh_mtu2: Remove unnecessary OOM messages
clocksource: sh_cmt: Remove unnecessary OOM messages
clocksource: em_sti: Remove unnecessary OOM messages
clocksource: dw_apb_timer_of: Do not trace read_sched_clock
clocksource: Fix clocksource_mmio_readX_down
clocksource: Fix type confusion for clocksource_mmio_readX_Y
clocksource: sh_tmu: Fix channel IRQ retrieval in legacy case
clocksource: qcom: Implement read_current_timer for udelay
ntp: Make is_error_status() use its argument
ntp: Convert simple_strtol to kstrtol
timer_stats/doc: Fix /proc/timer_stats documentation
sched_clock: Remove deprecated setup_sched_clock() API
ARM: sun6i: a31: Add support for the High Speed Timers
clocksource: sun5i: Add support for reset controller
clocksource: efm32: use $vendor,$device scheme for compatible string
KConfig: Vexpress: build the ARM_GLOBAL_TIMER with vexpress platform
...
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary DTS nodes to enable the micro-HDMI output on Parlor
board.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector
for a 4.3'' LCD. Add a common include file for this configuration, and
use it on relevant expansion boards.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.
This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it.
The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch add support for lcd display on gta04 board. Display control
is connected to spi (used spi bitbang driver).
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
omap5-uevm has a single HDMI output. Add the necessary display
information, including pinmuxing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
omap5-uevm has a tca6424a I/O expander. Add it to the .dts file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add DT data for am437x-gp-evm's LCD panel.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add DT data for the display subsystem for AM4372. The DSS on AM4372 is
basically OMAP3's DSS, without DSI and VENC blocks.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
As with previous release, this continues to be among the largest branches
we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OvOG
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
The bulk of this branch is updates for Renesas Shmobile. They are still
doing some enablement for classic boards first, and then come up with DT
bindings when they've had a chance to learn more about the hardware. Not
necessarily a bad way to go about it, and they're looking at moving some
of the temporary board code resulting from it to drivers/staging instead
to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of in
the cleanup branch due to the other board changes depending on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=lWof
-----END PGP SIGNATURE-----
Merge tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC board support updates from Olof Johansson:
"The bulk of this branch is updates for Renesas Shmobile. They are
still doing some enablement for classic boards first, and then come up
with DT bindings when they've had a chance to learn more about the
hardware. Not necessarily a bad way to go about it, and they're
looking at moving some of the temporary board code resulting from it
to drivers/staging instead to avoid the churn here.
As a result of the shmobile clock cleanups, we end up merging quite a
bit of SH code here as well. We ended up merging it here instead of
in the cleanup branch due to the other board changes depending on it"
* tag 'boards-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (130 commits)
ARM: davinci: remove checks for CONFIG_USB_MUSB_PERIPHERAL
ARM: add drivers for Colibri T30 to multi_v7_defconfig
ARM: shmobile: Remove Genmai reference DTS
ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
ARM: shmobile: genmai-reference: Remove legacy clock support
ARM: shmobile: Remove non-multiplatform Genmai reference support
ARM: configs: enable XHCI mvebu support in multi_v7_defconfig
ARM: OMAP: replace checks for CONFIG_USB_GADGET_OMAP
ARM: OMAP: AM3517EVM: remove check for CONFIG_PANEL_SHARP_LQ043T1DG01
ARM: OMAP: SX1: remove check for CONFIG_SX1_OLD_FLASH
ARM: OMAP: remove some dead code
ARM: OMAP: omap3stalker: remove two Kconfig macros
ARM: tegra: tegra_defconfig updates
ARM: shmobile: r7s72100: use workaround for non DT-clocks
ARM: shmobile: Add forward declaration of struct clk to silence warning
ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
ARM: shmobile: r7s72100: add spi clocks to dtsi
ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
ARM: shmobile: r7s72100: add i2c clocks to dtsi
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Cleanups for 3.16. Among these are:
- A bunch of misc cleanups for Broadcom platforms, mostly housekeeping
- Enabling Common Clock Framework on the older s3c24xx Samsung chipsets
- Cleanup of the Versatile Express system controller code, moving it to syscon
- Power management cleanups for OMAP platforms
+ a handful of other cleanups across the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wuX4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC cleanups from Olof Johansson:
"Cleanups for 3.16. Among these are:
- a bunch of misc cleanups for Broadcom platforms, mostly
housekeeping
- enabling Common Clock Framework on the older s3c24xx Samsung
chipsets
- cleanup of the Versatile Express system controller code, moving it
to syscon
- power management cleanups for OMAP platforms
plus a handful of other cleanups across the place"
* tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
ARM: kconfig: allow PCI support to be selected with ARCH_MULTIPLATFORM
clk: samsung: fix build error
ARM: vexpress: refine dependencies for new code
clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares __initdata
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files
ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops
ARM: OMAP3/OMAP4: PRM: add prm_features flags and add IO wakeup under it
ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup
ARM: OMAP2+: PRM: remove unnecessary cpu_is_XXX calls from prm_init / exit
ARM: OMAP2+: PRCM: cleanup some header includes
...
A small selection of fixes coming in late during the release cycle and
not being critical enough for 3.15 inclusion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=aWLB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC low-priority fixes from Olof Johansson:
"A small selection of fixes coming in late during the release cycle and
not being critical enough for 3.15 inclusion"
* tag 'fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: armadillo800eva: fixup HDMI sound flags setting
ARM: msm: Silence readb/writeb warnings due to missing IOMEM()
ARM: dts: am43xx: fix starting offset of NAND.filesystem MTD partition
ARM: dts: am335x-boneblack: remove use of ti,vcc-aux-disable-is-sleep
ARM: OMAP2+: free use_gptimer_clksrc variable after boot
ARM: OMAP5: Redo THUMB mode switch on secondary CPU
ARM: dts: AM4372: add l3-noc information
ARM: dts: DRA7: Use dra7-l3-noc instead of omap4-l3-noc
reset: Add of_reset_control_get to reset.h
