Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.
The intent was to avoid udp_lib_checksum_complete() overhead.
But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing an OpenStack configuration using VXLANs I saw the following
call trace:
RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
RSP: 0018:ffff88103867bc50 EFLAGS: 00010286
RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
FS: 0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
Stack:
ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
Call Trace:
[<ffffffff81576515>] ? skb_checksum+0x35/0x50
[<ffffffff815733c0>] ? skb_push+0x40/0x40
[<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
[<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
[<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
[<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
[<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
[<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
[<ffffffff815899d0>] net_rx_action+0x160/0x380
[<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
[<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
[<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
[<ffffffff8109a400>] ? sort_range+0x30/0x30
[<ffffffff81096da8>] kthread+0xd8/0xf0
[<ffffffff81693c82>] ret_from_fork+0x22/0x40
[<ffffffff81096cd0>] ? kthread_park+0x60/0x60
The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel. I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.
To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev. This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated. In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.
Fixes: 63058308cd ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP uses the generic socket backlog code, and this will soon
be changed to not disable BH when protocol is called back.
We need to use appropriate SNMP accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename UDP_INC_STATS_BH() to __UDP_INC_STATS(),
and UDP6_INC_STATS_BH() to __UDP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP_INC_STATS_BH() to __ICMP_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days (before linux-3.0), SNMP counters were duplicated,
one for user context, and one for BH context.
After commit 8f0ea0fe3a ("snmp: reduce percpu needs by 50%")
we have a single copy, and what really matters is preemption being
enabled or disabled, since we use this_cpu_inc() or __this_cpu_inc()
respectively.
We therefore kill SNMP_INC_STATS_USER(), SNMP_ADD_STATS_USER(),
NET_INC_STATS_USER(), NET_ADD_STATS_USER(), SCTP_INC_STATS_USER(),
SNMP_INC_STATS64_USER(), SNMP_ADD_STATS64_USER(), TCP_ADD_STATS_USER(),
UDP_INC_STATS_USER(), UDP6_INC_STATS_USER(), and XFRM_INC_STATS_USER()
Following patches will rename __BH helpers to make clear their
usage is not tied to BH being disabled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
We deleted a line of code and accidentally made the "return put_user()"
part of the if statement when it's supposed to be unconditional.
Fixes: 9f9a45beaa ('udp: do not expect udp headers on ioctl SIOCINQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the SO_REUSEPORT socket option, it is possible to create sockets
in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
the AF_INET6 sockets.
Prior to the commits referenced below, an incoming IPv4 packet would
always be routed to a socket of type AF_INET when this mixed-mode was used.
After those changes, the same packet would be routed to the most recently
bound socket (if this happened to be an AF_INET6 socket, it would
have an IPv4 mapped IPv6 address).
The change in behavior occurred because the recent SO_REUSEPORT optimizations
short-circuit the socket scoring logic as soon as they find a match. They
did not take into account the scoring logic that favors AF_INET sockets
over AF_INET6 sockets in the event of a tie.
To fix this problem, this patch changes the insertion order of AF_INET
and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the
list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
the tail of the list. This will force AF_INET sockets to always be
considered first.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On udp sockets, recv cmsg IP_CMSG_CHECKSUM returns a checksum over
the packet payload. Since commit e6afc8ace6 pulled the headers,
taking skb->data as the start of transport header is incorrect. Use
the transport header pointer.
Also, when peeking at an offset from the start of the packet, only
return a checksum from the start of the peeked data. Note that the
cmsg does not subtract a tail checkum when reading truncated data.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On udp sockets, ioctl SIOCINQ returns the payload size of the first
packet. Since commit e6afc8ace6 pulled the headers, the result is
incorrect when subtracting header length. Remove that operation.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add externally visible functions to lookup a UDP socket by skb. This
will be used for GRO in UDP sockets. These functions also check
if skb->dst is set, and if it is not skb->dev is used to get dev_net.
This allows calling lookup functions before dst has been set on the
skbuff.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable peeking at UDP datagrams at the offset specified with socket
option SOL_SOCKET/SO_PEEK_OFF. Peek at any datagram in the queue, up
to the end of the given datagram.
Implement the SO_PEEK_OFF semantics introduced in commit ef64a54f6e
("sock: Introduce the SO_PEEK_OFF sock option"). Increase the offset
on peek, decrease it on regular reads.
When peeking, always checksum the packet immediately, to avoid
recomputation on subsequent peeks and final read.
The socket lock is not held for the duration of udp_recvmsg, so
peek and read operations can run concurrently. Only the last store
to sk_peek_off is preserved.
Signed-off-by: Sam Kumar <samanthakumar@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove UDP transport headers before queueing packets for reception.
This change simplifies a follow-up patch to add MSG_PEEK support.
Signed-off-by: Sam Kumar <samanthakumar@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert would like not touching UDP socket refcnt for encapsulated
traffic. For this to happen, we need to use normal RCU rules, with a grace
period before freeing a socket. UDP sockets are not short lived in the
high usage case, so the added cost of call_rcu() should not be a concern.
This actually removes a lot of complexity in UDP stack.
Multicast receives no longer need to hold a bucket spinlock.
Note that ip early demux still needs to take a reference on the socket.
Same remark for functions used by xt_socket and xt_PROXY netfilter modules,
but this might be changed later.
Performance for a single UDP socket receiving flood traffic from
many RX queues/cpus.
Simple udp_rx using simple recvfrom() loop :
438 kpps instead of 374 kpps : 17 % increase of the peak rate.
v2: Addressed Willem de Bruijn feedback in multicast handling
- keep early demux break in __udp4_lib_demux_lookup()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.
Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.
Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Process socket-level control messages by invoking
__sock_cmsg_send in ip_cmsg_send for control messages on
the SOL_SOCKET layer.
This makes sure whenever ip_cmsg_send is called in udp, icmp,
and raw, we also process socket-level control messages.
Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv4 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ingress ipv4 broadcast datagrams are dropped since,
in udp_v4_early_demux(), ip_check_mc_rcu() is invoked even on
bcast packets.
This patch addresses the issue, invoking ip_check_mc_rcu()
only for mcast packets.
Fixes: 6e54030932 ("ipv4/udp: Verify multicast group is ours in upd_v4_early_demux()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.
Callers are responsible for the freeing.
Many thanks to Dmitry for the report and diagnostic.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dst device doesn't support it, it'll get fixed up later anyway
by validate_xmit_skb(). Also, this allows us to take advantage of LCO
to avoid summing the payload multiple times.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arithmetic properties of the ones-complement checksum mean that a
correctly checksummed inner packet, including its checksum, has a ones
complement sum depending only on whatever value was used to initialise
the checksum field before checksumming (in the case of TCP and UDP,
this is the ones complement sum of the pseudo header, complemented).
Consequently, if we are going to offload the inner checksum with
CHECKSUM_PARTIAL, we can compute the outer checksum based only on the
packed data not covered by the inner checksum, and the initial value of
the inner checksum field.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change extends the fast SO_REUSEPORT socket lookup implemented
for UDP to TCP. Listener sockets with SO_REUSEPORT and the same
receive address are additionally added to an array for faster
random access. This means that only a single socket from the group
must be found in the listener list before any socket in the group can
be used to receive a packet. Previously, every socket in the group
needed to be considered before handing off the incoming packet.
This feature also exposes the ability to use a BPF program when
selecting a socket from a reuseport group.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a combination of connected and un-connected sockets, Dmitry
was able to trigger soft lockups with his fuzzer.
The problem is that sockets in the SO_REUSEPORT array might have
different scores.
Right after sk2=socket(), setsockopt(sk2,...,SO_REUSEPORT, on) and
bind(sk2, ...), but _before_ the connect(sk2) is done, sk2 is added into
the soreuseport array, with a score which is smaller than the score of
first socket sk1 found in hash table (I am speaking of the regular UDP
hash table), if sk1 had the connect() done, giving a +8 to its score.
hash bucket [X] -> sk1 -> sk2 -> NULL
sk1 score = 14 (because it did a connect())
sk2 score = 6
SO_REUSEPORT fast selection is an optimization. If it turns out the
score of the selected socket does not match score of first socket, just
fallback to old SO_REUSEPORT logic instead of trying to be too smart.
Normal SO_REUSEPORT users do not mix different kind of sockets, as this
mechanism is used for load balance traffic.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Craig Gallek <kraigatgoog@gmail.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket-lookup path did not pass along the skb in question
in my original BPF-based socket selection patch. The skb in the
udpN_lib_lookup2 path can be used for BPF-based socket selection just
like it is in the 'traditional' udpN_lib_lookup path.
udpN_lib_lookup2 kicks in when there are greater than 10 sockets in
the same hlist slot. Coincidentally, I chose 10 sockets per
reuseport group in my functional test, so the lookup2 path was not
excersised. This adds an additional set of tests with 20 sockets.
Fixes: 538950a1b7 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
Fixes: 3ca8e40299 ("soreuseport: BPF selection functional test")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commands run in a vrf context are not failing as expected on a route lookup:
root@kenny:~# ip ro ls table vrf-red
unreachable default
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
ping: Warning: source address might be selected on device other than vrf-red.
PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.
--- 10.100.1.254 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms
Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
connect: No route to host
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose socket options for setting a classic or extended BPF program
for use when selecting sockets in an SO_REUSEPORT group. These options
can be used on the first socket to belong to a group before bind or
on any socket in the group after bind.
This change includes refactoring of the existing sk_filter code to
allow reuse of the existing BPF filter validation checks.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include a struct sock_reuseport instance when a UDP socket binds to
a specific address for the first time with the reuseport flag set.
When selecting a socket for an incoming UDP packet, use the information
available in sock_reuseport if present.
This required adding an additional field to the UDP source address
equality function to differentiate between exact and wildcard matches.
The original use case allowed wildcard matches when checking for
existing port uses during bind. The new use case of adding a socket
to a reuseport group requires exact address matching.
Performance test (using a machine with 2 CPU sockets and a total of
48 cores): Create reuseport groups of varying size. Use one socket
from this group per user thread (pinning each thread to a different
core) calling recvmmsg in a tight loop. Record number of messages
received per second while saturating a 10G link.
10 sockets: 18% increase (~2.8M -> 3.3M pkts/s)
20 sockets: 14% increase (~2.9M -> 3.3M pkts/s)
40 sockets: 13% increase (~3.0M -> 3.4M pkts/s)
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backport of this upstream commit into stable kernels :
89c22d8c3b ("net: Fix skb csum races when peeking")
exposed a bug in udp stack vs MSG_PEEK support, when user provides
a buffer smaller than skb payload.
In this case,
skb_copy_and_csum_datagram_iovec(skb, sizeof(struct udphdr),
msg->msg_iov);
returns -EFAULT.
This bug does not happen in upstream kernels since Al Viro did a great
job to replace this into :
skb_copy_and_csum_datagram_msg(skb, sizeof(struct udphdr), msg);
This variant is safe vs short buffers.
For the time being, instead reverting Herbert Xu patch and add back
skb->ip_summed invalid changes, simply store the result of
udp_lib_checksum_complete() so that we avoid computing the checksum a
second time, and avoid the problematic
skb_copy_and_csum_datagram_iovec() call.
This patch can be applied on recent kernels as it avoids a double
checksumming, then backported to stable kernels as a bug fix.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
These netif flags are unnecessary convolutions. It is more
straightforward to just use NETIF_F_HW_CSUM, NETIF_F_IP_CSUM,
and NETIF_F_IPV6_CSUM directly.
This patch also:
- Cleans up can_checksum_protocol
- Simplifies netdev_intersect_features
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_INCOMING_CPU as added in commit 2c8c56e15d was a getsockopt() command
to fetch incoming cpu handling a particular TCP flow after accept()
This commits adds setsockopt() support and extends SO_REUSEPORT selection
logic : If a TCP listener or UDP socket has this option set, a packet is
delivered to this socket only if CPU handling the packet matches the specified
one.
This allows to build very efficient TCP servers, using one listener per
RX queue, as the associated TCP listener should only accept flows handled
in softirq by the same cpu.
This provides optimal NUMA behavior and keep cpu caches hot.
Note that __inet_lookup_listener() still has to iterate over the list of
all listeners. Following patch puts sk_refcnt in a different cache line
to let this iteration hit only shared and read mostly cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add operation to l3mdev to lookup source address for a given flow.
Add support for the operation to VRF driver and convert existing
IPv4 hooks to use the new lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IFF_VRF_MASTER to IFF_L3MDEV_MASTER and update the name of the
netif_is_vrf and netif_index_is_vrf macros.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen reported that the recent change to add oif to dst lookups breaks
the VTI use case. The problem is that with the oif set in the flow struct
the comparison to the nh_oif is triggered. Fix by splitting the
FLOWI_FLAG_VRFSRC into 2 flags -- one that triggers the vrf device cache
bypass (FLOWI_FLAG_VRFSRC) and another telling the lookup to not compare
nh oif (FLOWI_FLAG_SKIP_NH_OIF).
Fixes: 42a7b32b73 ("xfrm: Add oif to dst lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For unconnected UDP sockets using a VRF device lookup source address
based on VRF table. This allows the UDP header to be properly setup
before showing up at the VRF device via the dst.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast dst are not cached. They carry DST_NOCACHE.
As mentioned in commit f886497212 ("ipv4: fix dst race in
sk_dst_get()"), these dst need special care before caching them
into a socket.
Caching them is allowed only if their refcnt was not 0, ie we
must use atomic_inc_not_zero()
Also, we must use READ_ONCE() to fetch sk->sk_rx_dst, as mentioned
in commit d0c294c53a ("tcp: prevent fetching dst twice in early demux
code")
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Tested-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Reported-by: Alex Gartrell <agartrell@fb.com>
Cc: Michal Kubeček <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
421b3885bf "udp: ipv4: Add udp early
demux" introduced a regression that allowed sockets bound to INADDR_ANY
to receive packets from multicast groups that the socket had not joined.
For example a socket that had joined 224.168.2.9 could also receive
packets from 225.168.2.9 despite not having joined that group if
ip_early_demux is enabled.
Fix this by calling ip_check_mc_rcu() in udp_v4_early_demux() to verify
that the multicast packet is indeed ours.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two problems in UDP stack related to bogus checksums :
1) We return -EAGAIN to application even if receive queue is not empty.
This breaks applications using edge trigger epoll()
2) Under UDP flood, we can loop forever without yielding to other
processes, potentially hanging the host, especially on non SMP.
This patch is an attempt to make things better.
We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for non-NULL pointer is done as x != NULL and sometimes as x. x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
const qualifiers ease code review by making clear
which objects are not written in a function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event that skb_get_hash is unable to deduce a hash
in udp_flow_src_port we use a consistent random value instead.
This is specified in GRE/UDP draft section 3.2.1:
https://tools.ietf.org/html/draft-ietf-tsvwg-gre-in-udp-encap-04
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip_cmsg_recv_offset function which takes an offset argument
that indicates the starting offset in skb where data is being received
from. This will be useful in the case of UDP and provided checksum
to user space.
ip_cmsg_recv is an inline call to ip_cmsg_recv_offset with offset of
zero.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move convert_csum from udp_sock to inet_sock. This allows the
possibility that we can use convert checksum for different types
of sockets and also allows convert checksum to be enabled from
inet layer (what we'll want to do when enabling IP_CHECKSUM cmsg).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
