Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) A new selftest for nf_queue, from Florian Westphal. This test
covers two recent fixes: 07f8e4d0fd ("tcp: also NULL skb->dev
when copy was needed") and b738a185be ("tcp: ensure skb->dev is
NULL before leaving TCP stack").
2) The fwd action breaks with ifb. For safety in next extensions,
make sure the fwd action only runs from ingress until it is extended
to be used from a different hook.
3) The pipapo set type now reports EEXIST in case of subrange overlaps.
Update the rbtree set to validate range overlaps, so far this
validation is only done only from userspace. From Stefano Brivio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638 ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the software CBS does not consider the packet sending time
when depleting the credits. It caused the throughput to be
Idleslope[kbps] * (Port transmit rate[kbps] / |Sendslope[kbps]|) where
Idleslope * (Port transmit rate / (Idleslope + |Sendslope|)) = Idleslope
is expected. In order to fix the issue above, this patch takes the time
when the packet sending completes into account by moving the anchor time
variable "last" ahead to the send completion time upon transmission and
adding wait when the next dequeue request comes before the send
completion time of the previous packet.
changelog:
V2->V3:
- remove unnecessary whitespace cleanup
- add the checks if port_rate is 0 before division
V1->V2:
- combine variable "send_completed" into "last"
- add the comment for estimate of the packet sending
Fixes: 585d763af0 ("net/sched: Introduce Credit Based Shaper (CBS) qdisc")
Signed-off-by: Zh-yuan Ye <ye.zh-yuan@socionext.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->tc_redirected to 1, otherwise the ifb driver drops the packet.
Set skb->tc_from_ingress to 1 to reinject the packet back to the ingress
path after leaving the ifb egress path.
This patch inconditionally sets on these two skb fields that are
meaningful to the ifb driver. The existing forward action is guaranteed
to run from ingress path.
Fixes: 39e6dea28a ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make sure the forward action is only used from ingress.
Fixes: 39e6dea28a ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
...and return -ENOTEMPTY to the front-end in this case, instead of
proceeding. Currently, nft takes care of checking for these cases
and not sending them to the kernel, but if we drop the set_overlap()
call in nft we can end up in situations like:
# nft add table t
# nft add set t s '{ type inet_service ; flags interval ; }'
# nft add element t s '{ 1 - 5 }'
# nft add element t s '{ 6 - 10 }'
# nft add element t s '{ 4 - 7 }'
# nft list set t s
table ip t {
set s {
type inet_service
flags interval
elements = { 1-3, 4-5, 6-7 }
}
}
This change has the primary purpose of making the behaviour
consistent with nft_set_pipapo, but is also functional to avoid
inconsistent behaviour if userspace sends overlapping elements for
any reason.
v2: When we meet the same key data in the tree, as start element while
inserting an end element, or as end element while inserting a start
element, actually check that the existing element is active, before
resetting the overlap flag (Pablo Neira Ayuso)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace negations of nft_rbtree_interval_end() with a new helper,
nft_rbtree_interval_start(), wherever this helps to visualise the
problem at hand, that is, for all the occurrences except for the
comparison against given flags in __nft_rbtree_get().
This gets especially useful in the next patch.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
...and return -ENOTEMPTY to the front-end on collision, -EEXIST if
an identical element already exists. Together with the previous patch,
element collision will now be returned to the user as -EEXIST.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, the -EEXIST return code of ->insert() callbacks is ambiguous: it
might indicate that a given element (including intervals) already exists as
such, or that the new element would clash with existing ones.
If identical elements already exist, the front-end is ignoring this without
returning error, in case NLM_F_EXCL is not set. However, if the new element
can't be inserted due an overlap, we should report this to the user.
To this purpose, allow set back-ends to return -ENOTEMPTY on collision with
existing elements, translate that to -EEXIST, and return that to userspace,
no matter if NLM_F_EXCL was set.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3af ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b3 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b8 ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a place,
inet_dump_fib()
fib_table_dump
fn_trie_dump_leaf()
hlist_for_each_entry_rcu()
without rcu_read_lock() will trigger a warning,
WARNING: suspicious RCU usage
-----------------------------
net/ipv4/fib_trie.c:2216 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/1923:
#0: ffffffff8ce76e40 (rtnl_mutex){+.+.}, at: netlink_dump+0xd6/0x840
Call Trace:
dump_stack+0xa1/0xea
lockdep_rcu_suspicious+0x103/0x10d
fn_trie_dump_leaf+0x581/0x590
fib_table_dump+0x15f/0x220
inet_dump_fib+0x4ad/0x5d0
netlink_dump+0x350/0x840
__netlink_dump_start+0x315/0x3e0
rtnetlink_rcv_msg+0x4d1/0x720
netlink_rcv_skb+0xf0/0x220
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x306/0x460
netlink_sendmsg+0x44b/0x770
__sys_sendto+0x259/0x270
__x64_sys_sendto+0x80/0xa0
do_syscall_64+0x69/0xf4
entry_SYSCALL_64_after_hwframe+0x49/0xb3
Fixes: 18a8021a7b ("net/ipv4: Plumb support for filtering route dumps")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When application uses TCP_QUEUE_SEQ socket option to
change tp->rcv_next, we must also update tp->copied_seq.
Otherwise, stuff relying on tcp_inq() being precise can
eventually be confused.
For example, tcp_zerocopy_receive() might crash because
it does not expect tcp_recv_skb() to return NULL.
We could add tests in various places to fix the issue,
or simply make sure tcp_inq() wont return a random value,
and leave fast path as it is.
Note that this fixes ioctl(fd, SIOCINQ, &val) at the same
time.
Fixes: ee9952831c ("tcp: Initial repair mode")
Fixes: 05255b823a ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Splat looks like:
[ 120.954938][ C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[ 120.957761][ C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 120.959064][ C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[ 120.960054][ C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 120.962261][ C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[ 120.963149][ C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[ 120.966277][ C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[ 120.967293][ C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[ 120.968516][ C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[ 120.969718][ C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 120.972203][ C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[ 120.973379][ C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[ 120.974410][ C0] FS: 00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 120.979794][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 120.980773][ C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[ 120.981945][ C0] Call Trace:
[ 120.982411][ C0] <IRQ>
[ 120.982848][ C0] ? hsr_add_node+0x8c0/0x8c0 [hsr]
[ 120.983522][ C0] ? rcu_read_lock_held+0x90/0xa0
[ 120.984159][ C0] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 120.984944][ C0] hsr_handle_frame+0x1db/0x4e0 [hsr]
[ 120.985597][ C0] ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[ 120.986289][ C0] __netif_receive_skb_core+0x6bf/0x3170
[ 120.992513][ C0] ? check_chain_key+0x236/0x5d0
[ 120.993223][ C0] ? do_xdp_generic+0x1460/0x1460
[ 120.993875][ C0] ? register_lock_class+0x14d0/0x14d0
[ 120.994609][ C0] ? __netif_receive_skb_one_core+0x8d/0x160
[ 120.995377][ C0] __netif_receive_skb_one_core+0x8d/0x160
[ 120.996204][ C0] ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases retransmit logic will make a full skb copy, which will not
trigger the zeroing added in recent change
b738a185be ("tcp: ensure skb->dev is NULL before leaving TCP stack").
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Fixes: 28f8bfd1ac ("netfilter: Support iif matches in POSTROUTING")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Refetch IP header pointer after pskb_may_pull() in flowtable,
from Haishuang Yan.
2) Fix memleak in flowtable offload in nf_flow_table_free(),
from Paul Blakey.
3) Set control.addr_type mask in flowtable offload, from Edward Cree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->rbnode is sharing three skb fields : next, prev, dev
When a packet is sent, TCP keeps the original skb (master)
in a rtx queue, which was converted to rbtree a while back.
__tcp_transmit_skb() is responsible to clone the master skb,
and add the TCP header to the clone before sending it
to network layer.
skb_clone() already clears skb->next and skb->prev, but copies
the master oskb->dev into the clone.
We need to clear skb->dev, otherwise lower layers could interpret
the value as a pointer to a netdev.
This old bug surfaced recently when commit 28f8bfd1ac
("netfilter: Support iif matches in POSTROUTING") was merged.
Before this netfilter commit, skb->dev value was ignored and
changed before reaching dev_queue_xmit()
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Fixes: 28f8bfd1ac ("netfilter: Support iif matches in POSTROUTING")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Martin Zaharinov <micron10@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=bvsn
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20200319' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc, afs: Interruptibility fixes
Here are a number of fixes for AF_RXRPC and AFS that make AFS system calls
less interruptible and so less likely to leave the filesystem in an
uncertain state. There's also a miscellaneous patch to make tracing
consistent.
(1) Firstly, abstract out the Tx space calculation in sendmsg. Much the
same code is replicated in a number of places that subsequent patches
are going to alter, including adding another copy.
(2) Fix Tx interruptibility by allowing a kernel service, such as AFS, to
request that a call be interruptible only when waiting for a call slot
to become available (ie. the call has not taken place yet) or that a
call be not interruptible at all (e.g. when we want to do writeback
and don't want a signal interrupting a VM-induced writeback).
(3) Increase the minimum delay on MSG_WAITALL for userspace sendmsg() when
waiting for Tx buffer space as a 2*RTT delay is really small over 10G
ethernet and a 1 jiffy timeout might be essentially 0 if at the end of
the jiffy period.
(4) Fix some tracing output in AFS to make it consistent with rxrpc.
(5) Make sure aborted asynchronous AFS operations are tidied up properly
so we don't end up with stuck rxrpc calls.
(6) Make AFS client calls uninterruptible in the Rx phase. If we don't
wait for the reply to be fully gathered, we can't update the local VFS
state and we end up in an indeterminate state with respect to the
server.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_flow_rule_match() sets control.addr_type in key, so needs to also set
the corresponding mask. An exact match is wanted, so mask is all ones.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Freeing a flowtable with offloaded flows, the flow are deleted from
hardware but are not deleted from the flow table, leaking them,
and leaving their offload bit on.
Add a second pass of the disabled gc to delete the these flows from
the flow table before freeing it.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since pskb_may_pull may change skb->data, so we need to reload ip{v6}h at
the right place.
Fixes: a908fdec3d ("netfilter: nf_flow_table: move ipv6 offload hook code to nf_flow_table")
Fixes: 7d20868717 ("netfilter: nf_flow_table: move ipv4 offload hook code to nf_flow_table")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since nf_flow_snat_port and nf_flow_snat_ip{v6} call pskb_may_pull()
which may change skb->data, so we need to reload ip{v6}h at the right
place.
Fixes: a908fdec3d ("netfilter: nf_flow_table: move ipv6 offload hook code to nf_flow_table")
Fixes: 7d20868717 ("netfilter: nf_flow_table: move ipv4 offload hook code to nf_flow_table")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, on replace, the previous action instance params
is swapped with a newly allocated params. The old params is
only freed (via kfree_rcu), without releasing the allocated
ct zone template related to it.
Call tcf_ct_params_free (via call_rcu) for the old params,
so it will release it.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a markup for link with is "foo_". On this kernel-doc
comment, we don't want this, but instead, place a literal
reference. So, escape the literal with ``foo``, in order to
avoid this warning:
./net/core/dev.c:5195: WARNING: Unknown target name: "page_is".
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix referenced below causes a crash when an ERSPAN tunnel is created
without passing IFLA_INFO_DATA. Fix by validating passed-in data in the
same way as ipgre does.
Fixes: e1f8f78ffe ("net: ip_gre: Separate ERSPAN newlink / changelink callbacks")
Reported-by: syzbot+1b4ebf4dae4e510dd219@syzkaller.appspotmail.com
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Jakub Kicinski, we ethtool netlink code should respond
with an error if request head has flags set which are not recognized by
kernel, either as a mistake or because it expects functionality introduced
in later kernel versions.
To avoid unnecessary roundtrips, use extack cookie to provide the
information about supported request flags.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ba0dc5f6e0 ("netlink: allow sending extended ACK with cookie on
success") introduced a cookie which can be sent to userspace as part of
extended ack message in the form of NLMSGERR_ATTR_COOKIE attribute.
Currently the cookie is ignored if error code is non-zero but there is
no technical reason for such limitation and it can be useful to provide
machine parseable information as part of an error message.
Include NLMSGERR_ATTR_COOKIE whenever the cookie has been set,
regardless of error code.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
route4_change() allocates a new filter and copies values from
the old one. After the new filter is inserted into the hash
table, the old filter should be removed and freed, as the final
step of the update.
However, the current code mistakenly removes the new one. This
looks apparently wrong to me, and it causes double "free" and
use-after-free too, as reported by syzbot.
Reported-and-tested-by: syzbot+f9b32aaacd60305d9687@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+2f8c233f131943d6056d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+9c2df9fd5e9445b74e01@syzkaller.appspotmail.com
Fixes: 1109c00547 ("net: sched: RCU cls_route")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr module has been supporting the list and status command.
(HSR_C_GET_NODE_LIST and HSR_C_GET_NODE_STATUS)
These commands send node information to the user-space via generic netlink.
But, in the non-init_net namespace, these commands are not allowed
because .netnsok flag is false.
So, there is no way to get node information in the non-init_net namespace.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr_get_node_list() is to send node addresses to the userspace.
If there are so many nodes, it could fail because of buffer size.
In order to avoid this failure, the restart routine is added.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_get_node_{list/status}() are not under rtnl_lock() because
they are callback functions of generic netlink.
But they use __dev_get_by_index() without rtnl_lock().
So, it would use unsafe data.
In order to fix it, rcu_read_lock() and dev_get_by_index_rcu()
are used instead of __dev_get_by_index().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PACKET_RX_RING can cause multiple writers to access the same slot if a
fast writer wraps the ring while a slow writer is still copying. This
is particularly likely with few, large, slots (e.g., GSO packets).
Synchronize kernel thread ownership of rx ring slots with a bitmap.
Writers acquire a slot race-free by testing tp_status TP_STATUS_KERNEL
while holding the sk receive queue lock. They release this lock before
copying and set tp_status to TP_STATUS_USER to release to userspace
when done. During copying, another writer may take the lock, also see
TP_STATUS_KERNEL, and start writing to the same slot.
Introduce a new rx_owner_map bitmap with a bit per slot. To acquire a
slot, test and set with the lock held. To release race-free, update
tp_status and owner bit as a transaction, so take the lock again.
This is the one of a variety of discussed options (see Link below):
* instead of a shadow ring, embed the data in the slot itself, such as
in tp_padding. But any test for this field may match a value left by
userspace, causing deadlock.
* avoid the lock on release. This leaves a small race if releasing the
shadow slot before setting TP_STATUS_USER. The below reproducer showed
that this race is not academic. If releasing the slot after tp_status,
the race is more subtle. See the first link for details.
* add a new tp_status TP_KERNEL_OWNED to avoid the transactional store
of two fields. But, legacy applications may interpret all non-zero
tp_status as owned by the user. As libpcap does. So this is possible
only opt-in by newer processes. It can be added as an optional mode.
* embed the struct at the tail of pg_vec to avoid extra allocation.
The implementation proved no less complex than a separate field.
The additional locking cost on release adds contention, no different
than scaling on multicore or multiqueue h/w. In practice, below
reproducer nor small packet tcpdump showed a noticeable change in
perf report in cycles spent in spinlock. Where contention is
problematic, packet sockets support mitigation through PACKET_FANOUT.
And we can consider adding opt-in state TP_KERNEL_OWNED.
Easy to reproduce by running multiple netperf or similar TCP_STREAM
flows concurrently with `tcpdump -B 129 -n greater 60000`.
Based on an earlier patchset by Jon Rosen. See links below.
I believe this issue goes back to the introduction of tpacket_rcv,
which predates git history.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg237222.html
Suggested-by: Jon Rosen <jrosen@cisco.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jon Rosen <jrosen@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERSPAN shares most of the code path with GRE and gretap code. While that
helps keep the code compact, it is also error prone. Currently a broken
userspace can turn a gretap tunnel into a de facto ERSPAN one by passing
IFLA_GRE_ERSPAN_VER. There has been a similar issue in ip6gretap in the
past.
To prevent these problems in future, split the newlink and changelink code
paths. Split the ERSPAN code out of ipgre_netlink_parms() into a new
function erspan_netlink_parms(). Extract a piece of common logic from
ipgre_newlink() and ipgre_changelink() into ipgre_newlink_encap_setup().
Add erspan_newlink() and erspan_changelink().
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpfilter UMH code was recently changed to log its informative messages to
/dev/kmsg, however this interface doesn't support SEEK_CUR yet, used by
dprintf(). As result dprintf() returns -EINVAL and doesn't log anything.
However there already had some discussions about supporting SEEK_CUR into
/dev/kmsg interface in the past it wasn't concluded. Since the only user of
that from userspace perspective inside the kernel is the bpfilter UMH
(userspace) module it's better to correct it here instead waiting a conclusion
on the interface.
Fixes: 36c4357c63 ("net: bpfilter: print umh messages to /dev/kmsg")
Signed-off-by: Bruno Meneguele <bmeneg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 599be01ee5 ("net_sched: fix an OOB access in cls_tcindex")
I moved cp->hash calculation before the first
tcindex_alloc_perfect_hash(), but cp->alloc_hash is left untouched.
This difference could lead to another out of bound access.
cp->alloc_hash should always be the size allocated, we should
update it after this tcindex_alloc_perfect_hash().
Reported-and-tested-by: syzbot+dcc34d54d68ef7d2d53d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+c72da7b9ed57cde6fca2@syzkaller.appspotmail.com
Fixes: 599be01ee5 ("net_sched: fix an OOB access in cls_tcindex")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a use-after-free in tcindex_dump(). This is due to
the lack of RTNL in the deferred rcu work. We queue this work with
RTNL in tcindex_change(), later, tcindex_dump() is called:
fh = tp->ops->get(tp, t->tcm_handle);
...
err = tp->ops->change(..., &fh, ...);
tfilter_notify(..., fh, ...);
but there is nothing to serialize the pending
tcindex_partial_destroy_work() with tcindex_dump().
Fix this by simply holding RTNL in tcindex_partial_destroy_work(),
so that it won't be called until RTNL is released after
tc_new_tfilter() is completed.
Reported-and-tested-by: syzbot+653090db2562495901dc@syzkaller.appspotmail.com
Fixes: 3d210534cc ("net_sched: fix a race condition in tcindex_destroy()")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the handling of signals in client rxrpc calls made by the afs
filesystem. Ignore signals completely, leaving call abandonment or
connection loss to be detected by timeouts inside AF_RXRPC.
Allowing a filesystem call to be interrupted after the entire request has
been transmitted and an abort sent means that the server may or may not
have done the action - and we don't know. It may even be worse than that
for older servers.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the handling of sendmsg() with MSG_WAITALL for userspace to round the
timeout for when a signal occurs up to at least two jiffies as a 1 jiffy
timeout may end up being effectively 0 if jiffies wraps at the wrong time.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the interruptibility of kernel-initiated client calls so that they're
either only interruptible when they're waiting for a call slot to come
available or they're not interruptible at all. Either way, they're not
interruptible during transmission.
This should help prevent StoreData calls from being interrupted when
writeback is in progress. It doesn't, however, handle interruption during
the receive phase.
Userspace-initiated calls are still interruptable. After the signal has
been handled, sendmsg() will return the amount of data copied out of the
buffer and userspace can perform another sendmsg() call to continue
transmission.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Abstract out the calculation of there being sufficient Tx buffer space.
This is reproduced several times in the rxrpc sendmsg code.
Signed-off-by: David Howells <dhowells@redhat.com>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-03-12
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 8 day(s) which contain
a total of 12 files changed, 161 insertions(+), 15 deletions(-).
The main changes are:
1) Andrii fixed two bugs in cgroup-bpf.
2) John fixed sockmap.
3) Luke fixed x32 jit.
4) Martin fixed two issues in struct_ops.
5) Yonghong fixed bpf_send_signal.
6) Yoshiki fixed BTF enum.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug that was causing packets to be sent to the driver
without first calling dequeue() on the "child" qdisc. And the KASAN
report below shows that sending a packet without calling dequeue()
leads to bad results.
The problem is that when checking the last qdisc "child" we do not set
the returned skb to NULL, which can cause it to be sent to the driver,
and so after the skb is sent, it may be freed, and in some situations a
reference to it may still be in the child qdisc, because it was never
dequeued.
The crash log looks like this:
[ 19.937538] ==================================================================
[ 19.938300] BUG: KASAN: use-after-free in taprio_dequeue_soft+0x620/0x780
[ 19.938968] Read of size 4 at addr ffff8881128628cc by task swapper/1/0
[ 19.939612]
[ 19.939772] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.6.0-rc3+ #97
[ 19.940397] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qe4
[ 19.941523] Call Trace:
[ 19.941774] <IRQ>
[ 19.941985] dump_stack+0x97/0xe0
[ 19.942323] print_address_description.constprop.0+0x3b/0x60
[ 19.942884] ? taprio_dequeue_soft+0x620/0x780
[ 19.943325] ? taprio_dequeue_soft+0x620/0x780
[ 19.943767] __kasan_report.cold+0x1a/0x32
[ 19.944173] ? taprio_dequeue_soft+0x620/0x780
[ 19.944612] kasan_report+0xe/0x20
[ 19.944954] taprio_dequeue_soft+0x620/0x780
[ 19.945380] __qdisc_run+0x164/0x18d0
[ 19.945749] net_tx_action+0x2c4/0x730
[ 19.946124] __do_softirq+0x268/0x7bc
[ 19.946491] irq_exit+0x17d/0x1b0
[ 19.946824] smp_apic_timer_interrupt+0xeb/0x380
[ 19.947280] apic_timer_interrupt+0xf/0x20
[ 19.947687] </IRQ>
[ 19.947912] RIP: 0010:default_idle+0x2d/0x2d0
[ 19.948345] Code: 00 00 41 56 41 55 65 44 8b 2d 3f 8d 7c 7c 41 54 55 53 0f 1f 44 00 00 e8 b1 b2 c5 fd e9 07 00 3
[ 19.950166] RSP: 0018:ffff88811a3efda0 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff13
[ 19.950909] RAX: 0000000080000000 RBX: ffff88811a3a9600 RCX: ffffffff8385327e
[ 19.951608] RDX: 1ffff110234752c0 RSI: 0000000000000000 RDI: ffffffff8385262f
[ 19.952309] RBP: ffffed10234752c0 R08: 0000000000000001 R09: ffffed10234752c1
[ 19.953009] R10: ffffed10234752c0 R11: ffff88811a3a9607 R12: 0000000000000001
[ 19.953709] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000
[ 19.954408] ? default_idle_call+0x2e/0x70
[ 19.954816] ? default_idle+0x1f/0x2d0
[ 19.955192] default_idle_call+0x5e/0x70
[ 19.955584] do_idle+0x3d4/0x500
[ 19.955909] ? arch_cpu_idle_exit+0x40/0x40
[ 19.956325] ? _raw_spin_unlock_irqrestore+0x23/0x30
[ 19.956829] ? trace_hardirqs_on+0x30/0x160
[ 19.957242] cpu_startup_entry+0x19/0x20
[ 19.957633] start_secondary+0x2a6/0x380
[ 19.958026] ? set_cpu_sibling_map+0x18b0/0x18b0
[ 19.958486] secondary_startup_64+0xa4/0xb0
[ 19.958921]
[ 19.959078] Allocated by task 33:
[ 19.959412] save_stack+0x1b/0x80
[ 19.959747] __kasan_kmalloc.constprop.0+0xc2/0xd0
[ 19.960222] kmem_cache_alloc+0xe4/0x230
[ 19.960617] __alloc_skb+0x91/0x510
[ 19.960967] ndisc_alloc_skb+0x133/0x330
[ 19.961358] ndisc_send_ns+0x134/0x810
[ 19.961735] addrconf_dad_work+0xad5/0xf80
[ 19.962144] process_one_work+0x78e/0x13a0
[ 19.962551] worker_thread+0x8f/0xfa0
[ 19.962919] kthread+0x2ba/0x3b0
[ 19.963242] ret_from_fork+0x3a/0x50
[ 19.963596]
[ 19.963753] Freed by task 33:
[ 19.964055] save_stack+0x1b/0x80
[ 19.964386] __kasan_slab_free+0x12f/0x180
[ 19.964830] kmem_cache_free+0x80/0x290
[ 19.965231] ip6_mc_input+0x38a/0x4d0
[ 19.965617] ipv6_rcv+0x1a4/0x1d0
[ 19.965948] __netif_receive_skb_one_core+0xf2/0x180
[ 19.966437] netif_receive_skb+0x8c/0x3c0
[ 19.966846] br_handle_frame_finish+0x779/0x1310
[ 19.967302] br_handle_frame+0x42a/0x830
[ 19.967694] __netif_receive_skb_core+0xf0e/0x2a90
[ 19.968167] __netif_receive_skb_one_core+0x96/0x180
[ 19.968658] process_backlog+0x198/0x650
[ 19.969047] net_rx_action+0x2fa/0xaa0
[ 19.969420] __do_softirq+0x268/0x7bc
[ 19.969785]
[ 19.969940] The buggy address belongs to the object at ffff888112862840
[ 19.969940] which belongs to the cache skbuff_head_cache of size 224
[ 19.971202] The buggy address is located 140 bytes inside of
[ 19.971202] 224-byte region [ffff888112862840, ffff888112862920)
[ 19.972344] The buggy address belongs to the page:
[ 19.972820] page:ffffea00044a1800 refcount:1 mapcount:0 mapping:ffff88811a2bd1c0 index:0xffff8881128625c0 compo0
[ 19.973930] flags: 0x8000000000010200(slab|head)
[ 19.974388] raw: 8000000000010200 ffff88811a2ed650 ffff88811a2ed650 ffff88811a2bd1c0
[ 19.975151] raw: ffff8881128625c0 0000000000190013 00000001ffffffff 0000000000000000
[ 19.975915] page dumped because: kasan: bad access detected
[ 19.976461] page_owner tracks the page as allocated
[ 19.976946] page last allocated via order 2, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NO)
[ 19.978332] prep_new_page+0x24b/0x330
[ 19.978707] get_page_from_freelist+0x2057/0x2c90
[ 19.979170] __alloc_pages_nodemask+0x218/0x590
[ 19.979619] new_slab+0x9d/0x300
[ 19.979948] ___slab_alloc.constprop.0+0x2f9/0x6f0
[ 19.980421] __slab_alloc.constprop.0+0x30/0x60
[ 19.980870] kmem_cache_alloc+0x201/0x230
[ 19.981269] __alloc_skb+0x91/0x510
[ 19.981620] alloc_skb_with_frags+0x78/0x4a0
[ 19.982043] sock_alloc_send_pskb+0x5eb/0x750
[ 19.982476] unix_stream_sendmsg+0x399/0x7f0
[ 19.982904] sock_sendmsg+0xe2/0x110
[ 19.983262] ____sys_sendmsg+0x4de/0x6d0
[ 19.983660] ___sys_sendmsg+0xe4/0x160
[ 19.984032] __sys_sendmsg+0xab/0x130
[ 19.984396] do_syscall_64+0xe7/0xae0
[ 19.984761] page last free stack trace:
[ 19.985142] __free_pages_ok+0x432/0xbc0
[ 19.985533] qlist_free_all+0x56/0xc0
[ 19.985907] quarantine_reduce+0x149/0x170
[ 19.986315] __kasan_kmalloc.constprop.0+0x9e/0xd0
[ 19.986791] kmem_cache_alloc+0xe4/0x230
[ 19.987182] prepare_creds+0x24/0x440
[ 19.987548] do_faccessat+0x80/0x590
[ 19.987906] do_syscall_64+0xe7/0xae0
[ 19.988276] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 19.988775]
[ 19.988930] Memory state around the buggy address:
[ 19.989402] ffff888112862780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 19.990111] ffff888112862800: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
[ 19.990822] >ffff888112862880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 19.991529] ^
[ 19.992081] ffff888112862900: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
[ 19.992796] ffff888112862980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Reported-by: Michael Schmidt <michael.schmidt@eti.uni-siegen.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA drivers should configure CPU and DSA ports to their
maximum speed. In many configurations this is sufficient to make the
link work.
In some cases it is necessary to configure the link to run slower,
e.g. because of limitations of the SoC it is connected to. Or back to
back PHYs are used and the PHY needs to be driven in order to
establish link. In this case, phylink is used.
Only instantiate phylink if it is required. If there is no PHY, or no
fixed link properties, phylink can upset a link which works in the
default configuration.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one error case, tpacket_rcv drops packets after incrementing the
ring producer index.
If this happens, it does not update tp_status to TP_STATUS_USER and
thus the reader is stalled for an iteration of the ring, causing out
of order arrival.
The only such error path is when virtio_net_hdr_from_skb fails due
to encountering an unknown GSO type.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
caifdevs->list is traversed using list_for_each_entry_rcu()
outside an RCU read-side critical section but under the
protection of rtnl_mutex. Hence, add the corresponding lockdep
expression to silence the following false-positive warning:
[ 10.868467] =============================
[ 10.869082] WARNING: suspicious RCU usage
[ 10.869817] 5.6.0-rc1-00177-g06ec0a154aae4 #1 Not tainted
[ 10.870804] -----------------------------
[ 10.871557] net/caif/caif_dev.c:115 RCU-list traversed in non-reader section!!
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bucket->lock is not needed in the sock_hash_free and sock_map_free
calls, in fact it is causing a splat due to being inside rcu block.
| BUG: sleeping function called from invalid context at net/core/sock.c:2935
| in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 62, name: kworker/0:1
| 3 locks held by kworker/0:1/62:
| #0: ffff88813b019748 ((wq_completion)events){+.+.}, at: process_one_work+0x1d7/0x5e0
| #1: ffffc900000abe50 ((work_completion)(&map->work)){+.+.}, at: process_one_work+0x1d7/0x5e0
| #2: ffff8881381f6df8 (&stab->lock){+...}, at: sock_map_free+0x26/0x180
| CPU: 0 PID: 62 Comm: kworker/0:1 Not tainted 5.5.0-04008-g7b083332376e #454
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20190727_073836-buildvm-ppc64le-16.ppc.fedoraproject.org-3.fc31 04/01/2014
| Workqueue: events bpf_map_free_deferred
| Call Trace:
| dump_stack+0x71/0xa0
| ___might_sleep.cold+0xa6/0xb6
| lock_sock_nested+0x28/0x90
| sock_map_free+0x5f/0x180
| bpf_map_free_deferred+0x58/0x80
| process_one_work+0x260/0x5e0
| worker_thread+0x4d/0x3e0
| kthread+0x108/0x140
| ? process_one_work+0x5e0/0x5e0
| ? kthread_park+0x90/0x90
| ret_from_fork+0x3a/0x50
The reason we have stab->lock and bucket->locks in sockmap code is to
handle checking EEXIST in update/delete cases. We need to be careful during
an update operation that we check for EEXIST and we need to ensure that the
psock object is not in some partial state of removal/insertion while we do
this. So both map_update_common and sock_map_delete need to guard from being
run together potentially deleting an entry we are checking, etc. But by the
time we get to the tear-down code in sock_{ma[|hash}_free we have already
disconnected the map and we just did synchronize_rcu() in the line above so
no updates/deletes should be in flight. Because of this we can drop the
bucket locks from the map free'ing code, noting no update/deletes can be
in-flight.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: Jakub Sitnicki <jakub@cloudflare.com>
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/158385850787.30597.8346421465837046618.stgit@john-Precision-5820-Tower
When trying to transmit to an unknown destination, the mesh code would
unconditionally transmit a HWMP PREQ even if HWMP is not the current
path selection algorithm.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20200305140409.12204-1-cavallar@lri.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
