This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran says:
====================
Add support for Broadcom's iProc MDIO and Cygnus Ethernet PHY
This patchset adds support for the iProc MDIO interface and the
Broadcom Cygnus SoC's internal Ethernet PHY.
The internal Ethernet PHY(s) in the Cygnus SoC's are accessed
via the MDIO interface found in most of the iProc based chips.
The patch also consolidates the common API's used by the
Broadcom phys to a common library. Existing Broadcom phy
drivers have been modified to use the common library API's.
This patch series is based on Linux v4.3-rc1 and is avaliable in:
https://github.com/Broadcom/cygnus-linux/tree/cygnus-net-phy-mdio-v3
The Ethernet driver for the iProc family will be submitted soon,
as will the device tree configurations for the different iProc
family SoCs.
Changes from v2:
- Modified drivers/net/phy/Kconfig to modify the BCM_CYGNUS_PHY
driver to 'depends on MDIO_BCM_IPROC' instead of 'select'.
- Added github branch to the cover letter
Changes from v1:
- Updated device tree documentation for the iProc MDIO driver
based on Florian's feedback.
- Moved the core register defines from the Cygnus PHY driver to
'include/linux/brcmphy.h' based on Florian's feedback.
- Created a new patch/commit to modify the bcm7xxx phy driver
to use the new core register defines.
- Modified the Kconfig entry for the Broadcom PHY library to
'tristate' instead of 'bool'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified the bcm7xxx phy driver to remove local core register
defines and use the common ones from "include/linux/brcmphy.h"
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).
This driver supports the following Broadcom Cygnus SoCs:
- BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
- BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)
The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom iProc MDIO bus interface.
The MDIO interface can be found in the Broadcom iProc family Soc's.
The MDIO bus is accessed using a combination of command and data
registers. This MDIO driver provides access to the Etherent GPHY's
connected to the MDIO bus.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for the Broadcom iProc MDIO
bus driver.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Shilimkar says:
====================
RDS: connection scalability and performance improvements
[v4]
Re-sending the same patches from v3 again since my repost of
patch 05/14 from v3 was whitespace damaged.
[v3]
Updated patch "[PATCH v2 05/14] RDS: defer the over_batch work to
send worker" as per David Miller's comment [4] to avoid the magic
value usage. Patch now makes use of already available but unused
send_batch_count module parameter. Rest of the patches are same as
earlier version v2 [3]
[v2]:
Dropped "[PATCH 05/15] RDS: increase size of hash-table to 8K" from
earlier version [1]. I plan to address the hash table scalability using
re-sizable hash tables as suggested by David Laight and David Miller [2]
This series addresses RDS connection bottlenecks on massive workloads and
improve the RDMA performance almost by 3X. RDS TCP also gets a small gain
of about 12%.
RDS is being used in massive systems with high scalability where several
hundred thousand end points and tens of thousands of local processes
are operating in tens of thousand sockets. Being RC(reliable connection),
socket bind and release happens very often and any inefficiencies in
bind hash look ups hurts the overall system performance. RDS bin hash-table
uses global spin-lock which is the biggest bottleneck. To make matter worst,
it uses rcu inside global lock for hash buckets.
This is being addressed by simply using per bucket rw lock which makes the
locking simple and very efficient. The hash table size is still an issue and
I plan to address it by using re-sizable hash tables as suggested on the list.
For RDS RDMA improvement, the completion handling is revamped so that we
can do batch completions. Both send and receive completion handlers are
split logically to achieve the same. RDS 8K messages being one of the
key usecase, mr pool is adapted to have the 8K mrs along with default 1M
mrs. And while doing this, few fixes and couple of bottlenecks seen with
rds_sendmsg() are addressed.
Series applies against 4.3-rc1 as well net-next. Its tested on Oracle
hardware with IB fabric for both bcopy as well as RDMA mode. RDS TCP is
tested with iXGB NIC. Like last time, iWARP transport is untested with
these changes. The patchset is also available at below git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux.git net/rds/4.3-v3
As a side note, the IB HCA driver I used for testing misses at least 3
important patches in upstream to see the full blown IB performance and
am hoping to get that in mainline with help of them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman says:
====================
net: Pass net through the output path v2
This is the next installment of my work to pass struct net through the
output path so the code does not need to guess how to figure out which
network namespace it is in, and ultimately routes can have output
devices in another network namespace.
The first patch in this series is a fix for a bug that came in when sk
was passed through the functions in the output path, and as such is
probably a candidate for net. At the same time my later patches depend
on it so sending the fix separately would be confusing.
The second patch in this series is another fix that for an issue that
came in when sk was passed through the output path. I don't think it
needs a backport as I don't think anyone uses the path where the code
was incorrect.
The rest of the patchset focuses on the path from xxx_local_out to
dst_output and in the end succeeds in passing sock_net(sk) from the
socket a packet locally originates on to the dst->output function.
Given the size reduction in the code I think this counts as a cleanup as
much as feature work.
There remain a number of helper functions (like ip option processing) to
take care of before the network stack can support destination devices in
other network namespaces but with this set of changes the backbone of
the work is done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute net once in ipvlan_process_v4_outbound and
ipvlan_process_v6_outbound and store it in a variable so that net does
not need to be recomputed next time it is used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute net and store it in a variable in pptp_xmit, so that the value
can be reused the next time it is needed.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute net and store it in a variable in the functions
ip_build_and_send_pkt and ip_queue_xmit so that it does not need to be
recomputed next time it is needed.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store net in a variable in ip_tunnel_xmit so it does not need
to be recomputed when it is used again.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop hidding the sk parameter with an inline helper function and make
all of the callers pass it, so that it is clear what the function is
doing.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only __ip6_local_out_sk has callers so rename __ip6_local_out_sk
__ip6_local_out and remove the previous __ip6_local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is confusing and silly hiding a parameter so modify all of
the callers to pass in the appropriate socket or skb->sk if
no socket is known.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with the other similar methods in the kernel pass a
struct sock into the dst_ops .local_out method.
Simplifying the socket passing case is needed a prequel to passing a
struct net reference into .local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dst_output_okfn with dst_output
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a packet has been encapsulated by a tunnel we should use the
tunnel sockets local multicast loopback flag to control if the
encapsulated packet should be locally loopback back.
Pass sk into ip_local_out_sk so that in the rare case we are dealing
with a tunneled packet whose tunnel destination address is a multicast
address the kernel properly decides to loopback this packet.
In practice I don't think this matters as ip_queue_xmit is used by
tcp, l2tp and sctp none of which I am aware of uses ip level
multicasting as they are all point to point communications protocols.
Let's fix this before someone uses ip_queue_xmit for a tunnel protocol
that does use multicast.
Fixes: aad88724c9 ("ipv4: add a sock pointer to dst->output() path.")
Fixes: b0270e9101 ("ipv4: add a sock pointer to ip_queue_xmit()")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the rare case where sk != skb->sk ip_local_out_sk arranges
to call dst->output differently if the skb is queued or not.
This is a bug.
Fix this bug by passing the sk parameter of ip_local_out_sk through
from ip_local_out_sk to __ip_local_out_sk (skipping __ip_local_out).
Fixes: 7026b1ddb6 ("netfilter: Pass socket pointer down through okfn().")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-07
This series contains updates to i40e and i40evf only.
Paul updates i40e to simply increase the amount of time we wait for a
reset to complete since we have seen in some rare occasions the reset
can take longer to complete.
Shannon updates the driver to turn on Wake-on-LAN by default if it is
enabled in the hardware config to begin with, rather than always disable
it and wait for the user to expressly turn it on. Added new device id's
and support for future devices. Fixed a possible type compare problem
between a size and possible negative number. Also fixed a shift value
that was wrong, which ended up with a bad bitmask. Did general house
cleaning of the driver to cleanup several low lying fruit in the
driver. Fixed an issue where new unicast address's would be added to
the VSI list and then immediately removed and would never actually
make it down to the hardware. Resolved the issue by removing the
separation from unicast and multicast in the search for filters to be
deleted.
Mitch fixes an issue where the hardware would continue to access the
memory formerly used by the rings for a VF which have been removed,
causing memory corruption or DMAR errors. To relieve this condition,
explicitly stop all rings associated with each VF before releasing its
resources. Also fixed a panic if the driver is unable to enable MSI-X
or its unable to acquire enough vectors, so propagate interrupt
allocation failure information to the calling function. Cleaned up
opcode that is not required.
Carolyn extends the size of the test available for the interrupt names
so that all the descriptive data available for the Flow Director
interrupts is not truncated.
Catherine fixes an issue where there was a possibility of speed getting
set to 0 if advertised is set to 0 (which is the case when autoneg is
disabled).
Jesse fixes the checksum on big endian machines, so added code to swap
it correctly. Also fixed a bug in the return from get_link_status()
where only true or false was being returned, but false could mean
multiple things. So allow the caller to get all the return values
in the call chain bubbled back to the source so that the reason for
the failure does not get lost.
Anjali adds statistics to keep track of how many times we ask the stack
to linearize the SKB because the hardware cannot handle SKBs with more
than 8 frags per segment/single packet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWE+cLAAoJECTWi3JdVIfQaCcH/3m85peX2dlE7KhI6gL9N76h
v4w7phygbkQqdD3v9bbbiRavkOMrrBCVNZ28uXIO/52LulrK9pzxRVTuhqdyVasO
CIWfAYinlxWJA0BnJ1E2toqXkym9PEILCixfPyYEI5iZTX3w3rosSdup9MzYTxZZ
N3Vux2bjgCiXp9hYbajITFQ9QRNXzn3hlI/Jl0/x9SkodkzCLJurMq5JAaFE+mhO
1W2S+ERvb0M5bHuyr1Bhf3Bzb8uMFTl1QK3vxRkSI9UVe3MSpQP9SZeN+ye7p7U0
hDlike9FxyLTMMnIe9XnsNEtBZmxNuAb7meF50Bi7xzItRGOIlDxB/Ak55uD4I8=
=hCDC
-----END PGP SIGNATURE-----
Merge tag 'regmap-offload-update-bits' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
regmap: Allow buses to provide a custom update_bits() operation
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
The chan_get() function just adds unnecessary indirection to calling
the chan_create() call. The only added value it gives is the chan->ops
assignment, but that can equally well be done in the calling code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The typical convention when having both a child and a parent channel
variable is to call the former 'chan' and the latter 'pchan'. When
there's only one variable it's called chan. Rename the 'pchan'
variables in the 6lowpan code to follow this convention.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All the chan_open() function now does is to call chan_create() so it
doesn't really add any value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP core code makes sure of setting the channel state to
BT_CONNECTED, so there's no need for the implementation code (6lowpan
in this case) to do it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP core code already sets the local MPS to a sane value. The
remote MPS value otoh comes from the remote side so there's no point
in trying to hard-code it to any value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The omtu value is determined by the remote peer so there's no point in
trying to hard-code it to any value. The IPSP specification otoh gives
a more reasonable value for the imtu, i.e. 1280.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When calling the hci_recv_frame driver function check for valid packet
types that the core should process. This should catch issues with
drivers trying to feed vendor packet types through this interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The manually coded frame reassembly is actually broken. The h4_recv_buf
helper from the UART driver is a perfect fit for frame reassembly for
this driver. So just export that function and use it here as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BPA-10x devices support tracing operation. Use the set_diag driver
callback to allow enabling and disabling that functionality.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller requires the HCI Reset command to be send when
closing the transport, the HCI_AUTO_OFF needs to be accounted for. The
current code tries to actually do that, but the flag gets cleared to
early. So store its value and use it that stored value instead of
checking for a flag that is always cleared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The set_diag driver callback allows enabling and disabling the vendor
specific diagnostic information. Since Broadcom chips have support for
a dedicated LM_DIAG channel, hook it up accordingly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a new debugfs entry for enabling and disabling the vendor
diagnostic mode. It is only exposed for drivers that provide the
set_diag driver callback and actually have an option for vendor
specific diagnostic information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Broadcom UART based controllers can send LM_DIAG messages with the
identifier 0x07 inside the HCI stream. These messages are 63 octets in
size and have no variable payload or length indicator.
This patch adds correct parsing information for the h4_recv_buf handler
and in case these packets are received, they are forwarded to the
Bluetooth core via hci_recv_diag interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introduce hci_recv_diag function for HCI drivers to allow sending vendor
specific diagnostic messages into the Bluetooth core stack. The messages
are not processed, but they are forwarded to the monitor channel and can
be retrieved by user space diagnostic tools.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth public device address might change during controller setup
and it makes it a lot simpler for monitoring tools if they just get told
what the new address is. In addition include the manufacturer / company
information of the controller. That allows for easy vendor specific HCI
command and event handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This opcode is not required. VFs that program RSS through the firmware
do it by interacting directly with the firmware, and do not need to use
the virtual channel for this functionality.
Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lower level functions are properly reporting errors, and higher-level
functions are correctly responding to errors, but the errors aren't
actually getting through. Typically, the middle-manager function seems
to want to shield its boss from any bad news.
This change fixes a panic if the driver is unable to enable MSI-X or is
unable to acquire enough vectors.
Change-ID: Ifd5787ce92519a5d97e4b465902db930d97b71a1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware has added additional status information to allow software
to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in
CEE DCBX mode.
This patch adds to support those additional checks and will only add
applications to the software table that have oper and sync bits set
without any error.
Change-ID: I0a76c52427dadf97d4dba4538a3068d05e4eb56b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the driver could call this function and have only true/false
returned, but false could mean multiple things like failure to read
or link was down. This change allows the caller to get all return values
in the call chain bubbled back to the source, which keeps information about
failures from being lost.
Also, in some unlikely scenarios, the firmware can become slow to respond
to admin queue (AQ) queries for link state. Should the AQ time out,
the driver can detect the state and avoid a link change when there
may have been none.
Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
