This is needed so that the IPU framebuffer scanout cannot be
starved by VPU or GPU activity.
Some boards like the SabreLite and SabreSD seem to set this in
the DCD already, but the documented register reset values do not
contain the necessary settings.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The fuse map of speed_grading[1:0] defines the max speed
of ARM, see below the definition:
2b'11: 1200000000Hz;
2b'10: 996000000Hz;
2b'01: 852000000Hz; -- i.MX6Q Only, exclusive with 996MHz.
2b'00: 792000000Hz;
Need to remove all illegal setpoints according to fuse
map.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx6qdl, the ENET RMII and PTP clock can come from either internal
ANATOP/CCM or external clock source through pad GPIO_16. But in case
of the external clock source, bit IOMUXC_GPR1[21] needs to be cleared.
The patch adds the support for systems that use an external clock source
and distinguishes above two cases by checking if the PTP clock specified
in device tree is the one coming from the internal ANATOP/CCM.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
When system enter suspend, we can set the DDR IO to
high-Z state to save DDR IOs' power consumption, this
operation can save many power(from ~26mA@1.5V to ~15mA@1.5V,
measured on i.MX6Q SabreSD board, R25) of DDR IOs. To
achieve that, we need to copy the suspend code to ocram
and run the low level hardware related code(set DDR IOs
to high-Z state) in ocram.
If there is no ocram space available, then system will
still do suspend in external DDR, hence no DDR IOs will
be set to high-Z.
The OCRAM usage layout is as below,
ocram suspend region(4K currently):
======================== high address ======================
.
.
.
^
^
^
imx6_suspend code
PM_INFO structure(imx6_cpu_pm_info)
======================== low address =======================
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the SolidRun HummingBoard. This commit adds support for
the following interfaces on this board:
- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0-DAY kernel build testing backend reports the following.
scripts/checkpatch.pl 0001-ARM-imx-add-support-code-for-IMX50-based-machines.patch
# many are suggestions rather than must-fix
ERROR: Use of const init definition must use __initconst
#80: arch/arm/mach-imx/mach-imx50.c:26:
+static const char *imx50_dt_board_compat[] __initdata = {
While at it, fix the error globally for IMX platform.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PEX860X has GPIO's which are used for PCI Reset lines on the
Gateworks Ventana boards. The GPIO's need to be set as output
level high so as to allow the PCIe devices to come out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The imx6q_restart() works fine with normal reboot but will run into
problem with emergency reboot like sysrq-b. In that case, of_iomap()
gets called from interrupt context and hence triggers the BUG_ON in
__get_vm_area_node().
Actually, since commit c1e31d1 (ARM: imx: create
mxc_arch_reset_init_dt() for DT boot), imx6q/dl should try to use
mxc_restart() by calling mxc_arch_reset_init_dt() beforehand, where
things like of_iomap() can be done.
The patch updates mxc_restart() a little bit to get it work for imx6q/dl
and kill imx6q_restart() completely.
Reported-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch enables soc bus infrastructure and adds a function
imx_soc_device_init() to report soc info via soc device interface for
imx6qdl and imx6sl. With the support, user space can get soc related
info by looking at sysfs like below.
$ cat /sys/devices/soc0/machine
Freescale i.MX6 Quad SABRE Smart Device Board
$ cat /sys/devices/soc0/family
Freescale i.MX
$ cat /sys/devices/soc0/soc_id
i.MX6Q
$ cat /sys/devices/soc0/revision
1.2
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch creates a common function imx_init_revision_from_anatop() by
merging imx6q_init_revision() and imx_anatop_get_digprog(), so that any
SoC that encodes revision info in anatop can use it to initialize
revision.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It calls imx_set_soc_revision() to set up soc revision in
imx6q_init_revision(), and replaces all the occurrences of
imx6q_revision() with common helper imx_get_soc_revision().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Commit cdc58d602d "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
The CLKO is widely used by imx6q board designs to clock audio codec.
Since most codecs accept 24 MHz frequency, let's initially set up CLKO
with OSC24M (cko <-- cko2 <-- osc). Then those board specific CLKO
setup for audio codec can be removed.
The board dts files also need an update on cko reference in codec node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.
Also add support for the KSZ9021RLRN PHY.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move anatop related (For USB) from board file to anatop driver
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that the cpu device registration initialises the of_node(if available)
appropriately for all the cpus, parsing here is redundant.
This patch removes all DT parsing and uses cpu->of_node instead.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The KSZ9031 is used on the i.MX6 based Data Modul eDM-QMX6
board. It needs the same fixup to the rx/tx delays as other
i.MX6 boards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The AR8031 is used on the i.MX6 based sabreSD, sabreauto and wandboard.
All need the same fixup, so add it for all i.MX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In current U-Boot the sabrelite, nitrogen6x and titanium all need
the same fixup for the ksz9021 phy. Instead of limiting the fixup
to a single board apply them for all.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WM8962 needs 24MHz clock for its MCLK, so choose PLL4 as the parent of clko1.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
To improve the performance and power consumption add an i.MX6
specific L2 cache initialization.
This configuration is taken from Freescale's kernel patch
"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]
with two additional improvements:
a) The L2X0_POWER_CTRL has only the two bits we set. So no need
to read the register before. Remove the register read done
in Freescale's patch.
b) In the L2X0_PREFETCH_CTRL register, besides the double linefill (bit[30]),
additionally enable the instruction and data prefetch (bit[29-28]).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
* Enable anatop, well bisa and RBC for suspend to optimize the power
consumption a little bit
* Clock changes for TVE, LDB, PATA, SRTC support
* Add System Reset Controller (SRC) support for imx5 and imx6
* Add initial imx6dl support based on imx6q code
* Kconfig for cpufreq-cpu0, defconfig updates and few other changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRZ/viAAoJEFBXWFqHsHzOyqUH/2t7CCwlfTVUJYDCeo6PaE9x
41cV5zG6RvX1OfkRUmJ2N2klGn4zhwg6GHsCDQmvs+IODs4E7JeB9M92FAaPng71
NnuuwCQ01iIoaTtkz8z/n3tSet3fYB+xfNCMJoWIyS0edFFkCjOgnqRsA0pHRIOp
G6ey1kU80D0f4+DjAUg1mkIvJrZxbRKDwmwqfDGJzQ4VU7cv70n027YuMKbeMyCC
zdeKmpKSEl9AY+O/zeMrf03zEW+kdZ4eB6cTUFlpzYwPYY9o+XHx0U0535F7/x4+
KObUZ9Qg7liP5WO3ZzkVff5HJqPs6s/q99eOsU4/okF1x0fpq2mSgIHlSw4HpK8=
=TuTx
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc2
From Shawn Guo:
The imx soc changes for 3.10:
* Enable anatop, well bisa and RBC for suspend to optimize the power
consumption a little bit
* Clock changes for TVE, LDB, PATA, SRTC support
* Add System Reset Controller (SRC) support for imx5 and imx6
* Add initial imx6dl support based on imx6q code
* Kconfig for cpufreq-cpu0, defconfig updates and few other changes
* tag 'imx-soc-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6: (275 commits)
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
ARM: i.MX53 Add the cko1, cko2 clock outputs.
staging: drm/imx: Use SRC to reset IPU
ARM i.MX6q: Add GPU, VPU, IPU, and OpenVG resets to System Reset Controller (SRC)
ARM: imx: do not use regmap_read for ANADIG_DIGPROG
ARM i.MX6q: set the LDB serial clock parent to the video PLL
ARM i.MX6q: Add audio/video PLL post dividers for i.MX6q rev 1.1
ARM i.MX6q: fix ldb di divider and selector clocks
ARM i.MX53: fix ldb di divider and selector clocks
ARM i.MX: Add imx_clk_divider_flags and imx_clk_mux_flags
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Trivial change/change conflict in arch/arm/mach-imx/mach-imx6q.c resolved.
The i.MX6 DualLite/Solo is another i.MX6 family SoC, which is highly
compatible with i.MX6 Quad/Dual. And that's why we choose to support
it using imx6q code with cpu_is_imx6dl() check when necessary.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Function imx_anatop_get_digprog() that reads register ANADIG_DIGPROG is
called to identify silicon version. Users might query silicon version
earlier than regmap subsystem is ready. For example, imx6q clock driver
query revision in mx6q_clocks_init(), where regmap is not initialized
yet.
Change imx_anatop_get_digprog() to map anatop block and read
ANADIG_DIGPROG in the native way, so that the function can work at very
early stage.
While at it, let's move imx_print_silicon_rev() back to
imx6q_timer_init() to have the message show up a little earlier.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
So it can be used in clk-imx6q.c for revision dependent clock tree setup.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.
As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix the following sparse warnings:
arch/arm/mach-imx/mach-imx6q.c:60:6: warning: symbol 'imx6q_restart' was not declared. Should it be static?
arch/arm/mach-imx/mach-imx6q.c:223:24: warning: symbol 'imx6q_cpufreq_pdev' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that we have OF based init with CLKSRC_OF, convert smp_twd init
function to use it and covert all callers of
twd_local_timer_of_register.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-omap@vger.kernel.org
Cc: spear-devel@list.st.com
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRL81iAAoJEIwa5zzehBx38egP/jkD5elNVtJ9Pu2AzwOnfYNG
oNfoVRr189VcCxQ8sq9xocnZDPyJEZzR/wnrs0wiFcFaMU1qQJpR4EgG8zhifM8D
plIFnf9H3z1/p+XKk7NwPII2RcSEQQ7jfK3UaPg0tQVOgGJiOh/czoYTRNHCaoQY
RF0W1K01uR15Pee95USIBvllyveJrss54dFB9ON1xGgf3aAHtyoPy/7Robm1FZAd
14msm3cN2v1lWXrTYvL8d+8sK6cIm1lOGOpc/VBSX5sjEBMiuGwnIDvajEvXIXMB
DNvkK6WpWSQsVv0oDLgWSBcgqpEElHmbzOo0WTMdec4hjaoLHRbeLdoaA7On/kpj
XofbXoXtsM2O5VSumhSfOWFtu22W3E4ng69UE5UkKknq8n+CKA5J0NmMW3PmCWws
xk9bk9I1feqy4uVkgaihCV5o+gtawaG6vOBEClLoVF+D6INMGts1FBN/MNZCBLck
hZjgr1/tcPlK5VMrxnlQBGRKcaXV1uGU+RWcV4jA1xR5GM3fQWMXe4aQohcYqglO
lpHeZCfy5JDexY30jfA+ldcG27PxUIYqhapanYTmcXMCSO4XZ4o1gy8oxDLrUoXe
/Whi3csxcGhitkUBWvxAeoOTeWRJonwyqEPJ/LpdNgnPmj8tnZKo3tc5wEKEywMA
qVDu5M4yi3FfkDK+0vp9
=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
This resolves one non-obvious merge conflict between the imx cpuidle
patches and the imx DT changes for 3.9.
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update operating-points per hardware document and add support for
1 GHz and 1.2 GHz frequencies.
400 MHz, 800 MHz and 1 GHz should be supported by all i.MX6Q chips,
while 1.2 GHz support needs to know from OTP fuse bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- It's based on imx-cleanup-3.9 to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCRzjAAoJEFBXWFqHsHzOOTYH/2YiAhCXDoovJ++leTTBKoFO
kRx2gvV0oxQYAjvRX4IiiwcuWjbCQI8ugiKxeH9Vn+jwHD8jKqzTINEUVQfKUud6
s8AI1/EqKwKnEFYFs/Fg6WxZHuHpoL/clpRB/5wZw1KoChmte2OnVU7d9vOt67iN
l0P4nPR18iwU5LFoDCnqMX50Dp9C56KEF2JhzBCQKW9TtRclwpcBNy6AsHb/TNOe
/nHN+Ku6/3xQEz2MPQ9QdmgFxnp9Pr8R6leJNg1Vg6UGRYrKxy0zVo+oFEXAZuUw
v6gnhdlvO6Ki/IKHcWkw7Q7pUDTuB6SttirQE9mBlPdc0V3kTU82SVtX9WAQhSs=
=rVol
-----END PGP SIGNATURE-----
Merge tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx6q cpuidle support for 3.9
- It's based on imx-cleanup-3.9 to avoid conflicts.
* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: support WAIT mode using cpuidle
ARM: imx: move imx6q_cpuidle_driver into a separate file
ARM: imx: mask gpc interrupts initially
ARM: imx: return zero in case next event gets a large increment
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Still, two delete/change conflicts caused by imx/cleanup:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
Add WAIT mode (ARM core clock gating) support to imx6q cpuidle driver.
As WAIT mode is broken on imx6q TO 1.0 and 1.1, it only enables the
support for revision 1.2 with chicken bit set.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move imx6q_cpuidle_driver into a separate file as more codes will
be added when WAIT mode gets implemented as cpuidle.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use debug_ll_io_init() to map low level debug port for imx6q, so that
arch/arm/mach-imx/lluart.c can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q_clock_map_io() becomes an empty function since imx6q clock driver
is moved to common clock framework. It's used nowhere now. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
