The warning shown up when ran with randconfig,
warning: (USB_DWC3) selects USB_XHCI_PLATFORM which has unmet direct dependencies (USB_SUPPORT && USB_XHCI_HCD)
Signed-off-by: joseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qgf/
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
to avoid sprinkling magic constants on the driver
we define a constant to be used when allocating
setup_buffer and ep0_bounce buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Issue an Update Transfer command after queuing a request to an isoc
EP with an active transfer. This is required according to the dwc3
databook. Pratyush Anand reports that this fixes a problem he was
having with Isoc IN transfers.
Tested-by: Pratyush Anand<pratyush.anand@st.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want to re-use that buffer for other USB
requests, so let's increase it to biggest
wMaxPacketSize for ep0 so it works for everything
we have in mind.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We separate between dwc3-omap helper functions to dwc3-core helper
functions. This will allow us to change the helper functions
implementation according to each module need.
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All revisions prior to 2.20a have a known issue which
causes metastability state on Run/Stop bit if we
configure the core to work on any of the USB2-only
speeds.
The suggested workaround is just to never configure the
core to anything other than SuperSpeed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have other revisions already released, let's
define revision macros for those so we can do
runtime detection of known erratas.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Array should be freed together with event buffers, since it was
allocated dynamically.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.
Cc: stable@vger.kernel.org
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.
On such case we were not increment r->actual as we should.
This patch fixes that mistake.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.
Cc: stable@vger.kernel.org
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
When applying commit 7d26b58 (fix failure path in
dwc3_pci_probe()), I mistakenly left out one of the
possible failures where we would return success even
on the error case.
This patch fixes that mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
Transfer resource index is cleared in hardware when XFERCOMPLETE
event is generated, so clear the driver's res_trans_idx variable
immediately after that event is received. The upcoming hibernation
patches depend on this change.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep_set_wedge() and dwc3_gadget_set_selfpowered() were
modifying dwc->flags/dwc->is_selfpowered without taking the lock.
Since those modifications are non-atomic, that could cause other
flags to be corrupted. Fix them both to take the lock.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The loop in dwc3_gadget_set_link_state() was using a udelay(500),
which is a long time to delay in interrupt context. Change it to
udelay(5) and increase the loop count to match.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_pci_probe() would return success even if the calls to
dwc3_get_device_id() or platform_device_alloc() fail, fix that.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Zero is a valid value for a microframe number. So remove the bogus
test for non-zero in dwc3_gadget_start_isoc().
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's wrong to use the size of array as an argument for strncat.
Memory corruption is possible. strlcat is exactly what we need here.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have a non-ISOC endpoint, we will not have a Link TRB
pointing to the beginning of the TRB pool. On such endpoints,
we don't want to let the driver wrap around the TRB pool
otherwise controller will hang waiting for a valid TRB.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We always return zero instead of the id we found.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/dwc3/core.c and drivers/usb/dwc3/dwc3-omap.c
included 'linux/module.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch enables to use devm_xxx functions during probing driver.
The devm_xxx series functions are able to release resource when the
driver is detatched. We can remove several codes to release resources
in the probe function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds Exynos Specific Glue layer to support USB peripherals
on Samsung Exynos5 chips.
[ balbi@ti.com : prevent compilation of Exynos glue layer
on platforms which don't provide clk API implementation ]
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RR+f
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: Gadget: changes for 3.4
This merge is rather big. Here's what it contains:
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
Conflicts:
drivers/usb/dwc3/gadget.c
those routines have everything we need to map/unmap
USB requests and it's better to use them.
In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fix a bug in f_serial, which expect the ep->desc to be NULL after
disabling an endpoint.
Cc: stable@vger.kernel.org
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.
Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.
Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.
In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When implementing the USB2 testmode support via debugfs,
Felipe has committed a mistake when counting the number
of letters of some of the strings, resulting on an off
by one error which prevented some of the Test modes to
be entered properly.
This patch, fixes that mistake.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This cuts down on the boilerplate code.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those transfer types are generally high bandwidth, so we
want to optimize transfers with those endpoints.
For that, databook suggests allocating 3 * wMaxPacketSize
of FIFO. Let's do that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
debugfs APIs will return NULL if it fails
to create the file/directory we ask it to
create.
Instead of checking for IS_ERR(ptr) we must
check for !ptr.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert our platform_data usage to OF property,
keep the legacy pdata for a while until the complete
conversion is done.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we set Run/Stop bit, we also move the
core to Rx.Detect state so that USB3 handshake
can start from a known location.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to dynamically re-size TxFifos for the
cases where default values will not do.
While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.
This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass Storage gadget will take some time to handle
the SetConfiguration request, but even on those
cases we should move to CONFIGURED state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
