Define two new "compatible" values for Ethernet
PHYs. "ethernet-phy-ieee802.3-c22" and "ethernet-phy-ieee802.3-c45"
are used to indicate a PHY uses the corresponding protocol.
If a PHY is "compatible" with "ethernet-phy-ieee802.3-c45", we
indicate this so that get_phy_device() can properly probe the device.
If get_phy_device() fails, it was probably due to failing the probe of
the PHY identifier registers. Since we have the device tree telling
us the PHY exists, go ahead and add it anyhow with a phy_id of zero.
There may be a driver match based on the "compatible" property.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS. Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag. Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.
get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false. The follow-on patch to of_mdio.c will pass true where
appropriate.
EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different boards may require different phy reset duration. Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using gpio_request_one will require the probe fail-out call gpio_free,
which is missing currently. Change to use devm_gpio_request_one to
fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bootloader or platform initialization code does not enable the
power supply to fec phy, we need to do it in fec driver before calling
fec_reset_phy to have the phy powered on.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that bootloader or platform initialization does not set up
fec pins, the fec_reset_phy will not be able to succeed, because
fec_reset_phy is currently called before devm_pinctrl_get_select_default.
Move fec_reset_phy call to the place between devm_pinctrl_get_select_default
and fec_enet_init to have above case be taken care.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
to indicate that the mising break statements are intended.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware returns error status, proceed to close the iSCSI connection.
Update version to 2.5.11.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This memory region is no longer used. Userspace gets the BAR address
directly from sysfs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so that it will work on any hypervisor.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We register with bnx2x before we allocate ctx_tbl structure, so it is
possible for bnx2x to call cnic_ctl before the structure is allocated.
This can sometimes cause NULL pointer dereference of cp->ctx_tbl. We
fix this by adding simple checking for valid state before proceeding.
The cnic_ctl call is RCU protected so we don't have to deal with race
conditions.
Because of the additional checking, we need to finish the shutdown
before clearing the CNIC_UP flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed spelling error in a comment as pointed out by DaveM.
Also refactored existing code a bit to provide placeholders for another ASIC
Bug workaround that will be checked-in soon after this.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports the ethtool's set_ringparam() and get_ringparam().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After freeing the buffer, the driver should change the value of
the pointer to NULL.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary members in sh_th_private.
This patch also removes unnecessary definitions in sh_eth.h
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_timer() called mod_timer() for itself. So, this patch
removes the function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the definition of bnx2x_tests_str_arr from char to static
char. This correction will also eliminate the sparse warning created in commit
cf2c1df62e.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. When FCoE offload driver is registered, copy its capabilities to the chip
scratchpad.
2. Copy FCoE/iSCSI MAC addresses in aligned manner to chip scratchpad.
3. Add FCoE/iSCSI statistics collection support
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLMSG_PUT() macro contains a hidden goto which makes the code hard
to audit and very error prone.
While been there also use the inline function nlmsg_data() instead of the
NLMSG_DATA() macro to do explicit type checking.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
team_adjust_ops should check for enabled ports, not all ports.
This may lead to division by zero. This patch fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.
This patch adds support for the Atmel RF230/231 radio transceivers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is easier to read if we specify which flags we want at the
condition instead of at the top of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_reset function resets chip, but this performs nothing when failed.
This changes sh_eth_reset return an error, when this failed in reset.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet IP of SH7734 and R8A7740 has selecting MII register.
The user needs to change a value according to MII to be used.
This adds the function to change the value of this register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of module parameters on caif hsi device, as
rtnl configuration parameters are already supported.
All caif hsi configuration data is put in cfhsi_config,
and default values in hsi_default_config.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of struct platform_device, and replace it with
struct cfhsi_ops. Updated variable names in the same
spirit:
cfhsi_get_dev to cfhsi_get_ops,
cfhsi->dev to cfhsi->ops and,
cfhsi->dev.drv to cfhsi->ops->cb_ops.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTNL support for managing the caif hsi interface.
The HSI HW interface is no longer registering as a device,
instead we use symbol_get to get hold of the HSI API.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove assignment at declaration when not needed.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericssion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_X with the corresponding netdev_X print
function when applicable.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericssion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregation_timeout is an unsigned long,
a test for less than zero can never become true,
compare with zero instead.
Signed-off-by: Kim Lilliestierna <kim.xx.lilliestierna@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify logic and remove dead code.
Signed-off-by: Kim Lilliestierna <kim.xx.lilliestierna@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix be_find_vfs() to check for matching bus number as well along with devfn
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are NETXEN_NIU_MAX_XG_PORTS ports.
Port indexing starts from zero.
Hence we should also return error for 'port == NETXEN_NIU_MAX_XG_PORTS'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
There are 'NETXEN_NIU_MAX_GBE_PORTS' GBE ports. Port indexing starts
from zero.
Hence we should also return error for "port == NETXEN_NIU_MAX_GBE_PORTS"
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
The following commit couldn't work if the RMCR is not set to 1.
"net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens"
commit id 79fba9f517
If RMCR is not set, the controller will clear the EDRRR after it received
a frame. In this case, the driver doesn't need to fix the value of
cur_rx/dirty_rx. The driver only needs it when the controll detects
receive descriptors are empty.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards
are very prone to NETDEV watchdog problems without this change. See
https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance.
I don't know why it *works*. It's depressingly effective though.
For the record:
- the problem may go along IOMMU (AMD-Vi) errors but it really looks
like a red herring.
- the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide,
the chipset now fetches several Rx descriptors at a time.
- long ago the driver ignored the RX_MULTI_EN bit.
e542a2269f changed the RxConfig
settings. Whatever the problem it's now labeled a regression.
- Realtek's own driver can identify two different 8168evl devices
(CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only
sees one. It sucks.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If usbnet is resumed by remote wakeup, generally there are
some packets comming to be handled, so allocate and submit
rx URBs in usbnet_resume to avoid delays introduced by tasklet.
Otherwise, usbnet may have been runtime suspended before the
usbnet_bh is executed to schedule Rx URBs.
Without the patch, usbnet can't recieve any packets from peer
in runtime suspend state if runtime PM is enabled and
autosuspend_delay is set as zero.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decreases dev->suspend_count in the -EBUSY failure path
of usbnet_suspend. Without the change, the later runtime suspend
will do nothing except for increasing dev->suspend_count.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ethtool functionality of accessing optic modules'
information and eeprom to the bnx2x driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically lower requested link speed to 1G in case 1G SFP+
module is detected.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a semantic change, cleaning some sections in which the bnx2x
handles the phy's registers.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several things:
1. Add static to function when possible.
2. Correct comments.
3. Change msleep(small) --> usleep_range(small, small*2).
Also correct existing calls to usleep_range.
4. Remove dead code.
5. Change 'if(rc != 0)' --> if(rc)
Most of these changes are purely semantic.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
