If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.
Cc: stable@vger.kernel.org
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__ieee80211_scan_completed is called from a worker. This
means that the following flow is possible.
* driver calls ieee80211_scan_completed
* mac80211 cancels the scan (that is already complete)
* __ieee80211_scan_completed runs
When scan_work will finally run, it will see that the scan
hasn't been aborted and might even trigger another scan on
another band. This leads to a situation where cfg80211's
scan is not done and no further scan can be issued.
Fix this by setting a new flag when a HW scan is being
cancelled so that no other scan will be triggered.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 scan processing could get stuck if roc work for pending, but
not started when a scan request was deferred due to such roc item.
Normally the deferred scan would be started from
ieee80211_start_next_roc(), but ieee80211_sw_roc_work() calls that only
if the finished ROC was started. Fix this by calling
ieee80211_run_deferred_scan() in the case the last ROC was not actually
started.
This issue was hit relatively easily in P2P find operations where Listen
state (remain-on-channel) and Search state (scan) are repeated in a
loop.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When clients are idle for too long, hostapd sends nullfunc frames for
probing. When those are acked by the client, the idle time needs to be
updated.
To make this work (and to avoid unnecessary probing), update sta->last_rx
whenever an ACK was received for a tx packet. Only do this if the flag
IEEE80211_HW_REPORTS_TX_ACK_STATUS is set.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "mac80211: select and adjust bitrates according to
channel mode" causes regression and breaks the extended supported rate
IE setting. Since "i" is starting with 8, so this is not necessary
to introduce "skip" here.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Reviewed-by: Jason Abele <jason@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an Ad-Hoc node receives packets with the Cell ID or its own MAC
address as source address, it hits a WARN_ON in sta_info_insert_check()
With many packets, this can massively spam the logs. One way that this
can easily happen is through having Cisco APs in the area with rouge AP
detection and countermeasures enabled.
Such Cisco APs will regularly send fake beacons, disassoc and deauth
packets that trigger these warnings.
To fix this issue, drop such spoofed packets early in the rx path.
Cc: stable@vger.kernel.org
Reported-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reported that with mac80211_hwsim, multicast TX was causing
crashes due to invalid vif->cab_queue assignment. It turns out that
this is caused by change_interface() getting invoked and not having
the vif->type/vif->p2p assigned correctly before calling the queue
check (ieee80211_check_queues). Fix this by passing the 'external'
interface type to the function and adjusting it accordingly.
While at it, also fix the error path in change_interface, it wasn't
correctly resetting to the external type but using the internal one
instead.
Fortunately this affects on hwsim because all other drivers set the
vif->type/vif->p2p variables when changing iftype. This shouldn't
be needed, but almost all implementations actually do it for their
own internal handling.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seth reports that some APs, notably the Netgear WNDAP360, send
invalid ECSA IEs in probe response frames with the operating
class and channel number both set to zero, even when no channel
switch is being done. As a result, any scan while connected to
such an AP results in the connection being dropped.
Fix this by ignoring any channel switch announcment in probe
response frames entirely, since we're connected to the AP we
will be receiving a beacon (and maybe even an action frame) if
a channel switch is done, which is sufficient.
Cc: stable@vger.kernel.org # 3.10
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 9.3.2.10, paragraph 4, QoS
data frames with a group address in the Address 1 field
have sequence numbers allocated from the same counter
as non-QoS data and management frames. Without this
flag, some drivers may not assign sequence numbers, and
in rare cases frames might get dropped. Set the control
flag accordingly.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the mesh STA responds to probe request from legacy STA
but now it will only respond to legacy STA if the legacy STA does include
the specific mesh ID or wildcard mesh ID in the probe request.
The iw patch "iw: scan using meshid" can be used either by legacy STA
or by mesh STA to do active scanning by inserting the mesh ID in the
probe request frame.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.
Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.
This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith reports that my commit af61a16518
("mac80211: add control port protocol TX control flag") broke ath9k
(aggregation). The reason is that I made minstrel_ht use the flag in
the TX status path, where it can have been overwritten by the driver.
Since we have no more space in info->flags, revert that part of the
change for now, until we can reshuffle the flags or so.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
my earlier patch "mac80211: change IBSS channel state to chandef"
created a regression by ignoring the channel parameter in
__ieee80211_sta_join_ibss, which breaks IBSS channel selection. This
patch fixes this situation by using the right channel and adopting the
selected bandwidth mode.
Cc: stable@vger.kernel.org
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.
This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"
Cc: stable@vger.kernel.org # 3.10
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IBSS needs to release the channel context when leaving
but I evidently missed that. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to (securely) keep connections alive after
the system was suspended for WoWLAN, we need some additional
APIs. We already have API (ieee80211_gtk_rekey_notify) to tell
wpa_supplicant about the new replay counter if GTK rekeying
was done by the device while the host was asleep, but that's
not sufficient.
If GTK rekeying wasn't done, we need to tell the host about
sequence counters for the GTK (and PTK regardless of rekeying)
that was used while asleep, add ieee80211_set_key_rx_seq() for
that.
If GTK rekeying was done, then we need to be able to disable
the old keys (with ieee80211_remove_key()) and allocate the
new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()).
If protocol offload (e.g. ARP) is implemented, then also the
TX sequence counter for the PTK must be updated, using the new
ieee80211_set_key_tx_seq() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel Switch will later require to generate beacons without setting
them immediately. Therefore split the presp generation in an own
function. Splitting the original very long function might be a good idea
anyway.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch decouples the power save processing from the frame decryption
by running the decrypt rx handler after sta_process. In the case where
the decryption failed for some reason, the stack used to not process
the PM and MOREDATA bits for that frame. The stack now always performs
power save processing regardless of the decryption result. That means that
encrypted data frames and NULLFUNC frames are now handled in the same way
regarding power save processing, making the stack more robust.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases mac80211 will scan before creating an IBSS
even if bssid and frequency have been forced by the user.
This is not needed and leads only to a delay in the IBSS
establishment phase.
Immediately create the cell if both bssid and frequency
(and fixed_freq is set) have been specified.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow lowest basic rate to be used for unicast management frame in
mesh. Otherwise, the lowest supported rate is used for unicast
management frame, such as 1Mbps for 2.4GHz and 6Mbps for 5GHz. Rename
the rc_send_low_broadcast to re_send_low_basicrate since now it is
also applied to unicast management frame in mesh.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places in the code (mac80211 and iwlmvm) use the same
TU_TO_JIFFIES() macro and could use TU_TO_EXP_TIME() that
mac80211 has. Make these available to everyone and use them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a per-station debugfs file indicating the TIDs (as
a bitmap) that the driver has data buffered on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap VHT info is 12 bytes (required to be aligned on 2) :
u16 known - IEEE80211_RADIOTAP_VHT_KNOWN_*
u8 flags - IEEE80211_RADIOTAP_VHT_FLAG_*
u8 bandwidth
u8 mcs_nss[4]
u8 coding
u8 group_id
u16 partial_aid
ATM mac80211 can handle IEEE80211_RADIOTAP_VHT_KNOWN_{GI,BANDWIDTH} and
mcs_nss[0] (i.e single user) in simple cases.
This is more a placeholder to let sniffers give more clues for VHT,
since we don't have yet the proper infrastructure/conventions
in mac80211 for complete feedback (e.g consider dynamic BW).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A station which is not authorized has to be purged earlier
to give it a chance to re-try to establish an IBSS/RSN
session soon. Set the timeout to 10 seconds.
Some refactoring has also been done to allow the IBSS
submodule to have its own expiring function.
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change mac80211 LED trigger code to use the generic
led_trigger_blink_oneshot() API for transmit and receive activity
indication.
This gives a better feedback to the user, as with the new API each
activity event results in a visible blink, while a constant traffic
results in a continuous blink at constant rate.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
[fix LED disabled build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.
Cc: stable@vger.kernel.org
Reported-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.
Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.
Work around this by ignoring the HT primary channel information in
beacons if we're already connected.
Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.
Cc: stable@vger.kernel.org [3.10]
Acked-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX status notification can get lost, or the frames could
get stuck on the queue, so don't wait for the callback
from the driver forever and instead time out after half
a second.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "3d9646d mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop. When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely. Replace goto with
break and carry on. This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking. Thanks to Derek Atkins
as an extra pair of debugging eyes.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit:
commit 12e7f51702
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Feb 28 10:55:26 2013 +0100
mac80211: cleanup generic suspend/resume procedures
removed check for deleting MONITOR and AP_VLAN when suspend. That can
cause a crash (i.e. in iwlagn_mac_remove_interface()) since we remove
interface in the driver that we did not add before.
Reference:
http://marc.info/?l=linux-kernel&m=137391815113860&w=2
Bisected-by: Ortwin Glück <odi@odi.ch>
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch is intended to avoid the buffering to non-assoc mesh STA
and also to avoid the triggering of frame to non-assoc mesh STA which
could cause kernel panic in specific hw.
One of the examples, is kernel panic happens to ath9k if user space
inserts the mesh STA and not proceed with the SAE and AMPE, and later
the same mesh STA is detected again. The sta_state of the mesh STA remains
at IEEE80211_STA_NONE and if the ieee80211_sta_ps_deliver_wakeup is called
and subsequently the ath_tx_aggr_wakeup, the kernel panic due to
ath_tx_node_init is not called before to initialize the require data
structures.
This issue is reported by Cedric Voncken before.
http://www.spinics.net/lists/linux-wireless/msg106342.html
[<831ea6b4>] ath_tx_aggr_wakeup+0x44/0xcc [ath9k]
[<83084214>] ieee80211_sta_ps_deliver_wakeup+0xb8/0x208 [mac80211]
[<830b9824>] ieee80211_mps_sta_status_update+0x94/0x108 [mac80211]
[<83099398>] ieee80211_sta_ps_transition+0xc94/0x34d8 [mac80211]
[<8022399c>] nf_iterate+0x98/0x104
[<8309bb60>] ieee80211_sta_ps_transition+0x345c/0x34d8 [mac80211]
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a driver (like hwsim) uses HW queue control an
active monitor vif needs to be used for the queues,
make the code do that. Otherwise we'd bail out and
drop the frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the Forwarding bit in Mesh Capability Info according
to dot11MeshForwarding as defined in IEEE 802.11-2012
section 8.4.2.100.8.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is an off-by-one error in the beacon generation for the ibss mode,
falsely a rate the extended supported rates which was already added to
supported rates, messing up the beacon. This was introduced by commit
"mac80211: select and adjust bitrates according to channel mode".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There appear to be two regressions in ibss.c when calling
ieee80211_sta_def_wmm_params():
* the second argument should be a rate length, not a rate array. This
was introduced by my commit "mac80211: select and adjust bitrates
according to channel mode"
* the third argument is not initialized (anymore), making further
checks within this function useless.
Since ieee80211_sta_def_wmm_params() is only used by ibss anyway,
remove the function entirely and handle the operating mode decision
immediately.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
