Add pernet support to xt_LOG by means of the new nf_log_set
function added in (30e0c6a netfilter: nf_log: prepare net
namespace support for loggers).
Since syslog ns has yet not been implemented, we don't want
the containers to DDOS host's syslogd. So only enable ebt_log
only from init_net and wait for syslog ns support
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add pernet support to ebt_log by means of the new nf_log_set
function added in (30e0c6a netfilter: nf_log: prepare net
namespace support for loggers).
Since syslog ns has yet not been implemented, we don't want
the containers to DDOS host's syslogd. So only enable ebt_log
only from init_net and wait for syslog ns support.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds netns support to nf_log and it prepares netns
support for existing loggers. It is composed of four major
changes.
1) nf_log_register has been split to two functions: nf_log_register
and nf_log_set. The new nf_log_register is used to globally
register the nf_logger and nf_log_set is used for enabling
pernet support from nf_loggers.
Per netns is not yet complete after this patch, it comes in
separate follow up patches.
2) Add net as a parameter of nf_log_bind_pf. Per netns is not
yet complete after this patch, it only allows to bind the
nf_logger to the protocol family from init_net and it skips
other cases.
3) Adapt all nf_log_packet callers to pass netns as parameter.
After this patch, this function only works for init_net.
4) Make the sysctl net/netfilter/nf_log pernet.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch makes this proc dentry pernet. So far only init_net
had a /proc/net/netfilter directory.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Because rev1 and rev3 of the target share the same hashing
generalize it by introduing nfqueue_hash().
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Current NFQUEUE target uses a hash, computed over source and
destination address (and other parameters), for steering the packet
to the actual NFQUEUE. This, however forgets about the fact that the
packet eventually is handled by a particular CPU on user request.
If E. g.
1) IRQ affinity is used to handle packets on a particular CPU already
(both single-queue or multi-queue case)
and/or
2) RPS is used to steer packets to a specific softirq
the target easily chooses an NFQUEUE which is not handled by a process
pinned to the same CPU.
The idea is therefore to use the CPU index for determining the
NFQUEUE handling the packet.
E. g. when having a system with 4 CPUs, 4 MQ queues and 4 NFQUEUEs it
looks like this:
+-----+ +-----+ +-----+ +-----+
|NFQ#0| |NFQ#1| |NFQ#2| |NFQ#3|
+-----+ +-----+ +-----+ +-----+
^ ^ ^ ^
| |NFQUEUE | |
+ + + +
+-----+ +-----+ +-----+ +-----+
|rx-0 | |rx-1 | |rx-2 | |rx-3 |
+-----+ +-----+ +-----+ +-----+
The NFQUEUEs not necessarily have to start with number 0, setups with
less NFQUEUEs than packet-handling CPUs are not a problem as well.
This patch extends the NFQUEUE target to accept a new
NFQ_FLAG_CPU_FANOUT flag. If this is specified the target uses the
CPU index for determining the NFQUEUE being used. I have to introduce
rev3 for this. The 'flags' are folded into _v2 'bypass'.
By changing the way which queue is assigned, I'm able to improve the
performance if the processes reading on the NFQUEUs are pinned
correctly.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We used a global BH disable in LOCAL_OUT hook.
Add _bh suffix to all places that need it and remove
the disabling from LOCAL_OUT and sync code.
Functions like ip_defrag need protection from
BH, so add it. As for nf_nat_mangle_tcp_packet, it needs
RCU lock.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is the final step in RCU conversion.
Things that are removed:
- svc->usecnt: now svc is accessed under RCU read lock
- svc->inc: and some unused code
- ip_vs_bind_pe and ip_vs_unbind_pe: no ability to replace PE
- __ip_vs_svc_lock: replaced with RCU
- IP_VS_WAIT_WHILE: now readers lookup svcs and dests under
RCU and work in parallel with configuration
Other changes:
- before now, a RCU read-side critical section included the
calling of the schedule method, now it is extended to include
service lookup
- ip_vs_svc_table and ip_vs_svc_fwm_table are now using hlist
- svc->pe and svc->scheduler remain to the end (of grace period),
the schedulers are prepared for such RCU readers
even after done_service is called but they need
to use synchronize_rcu because last ip_vs_scheduler_put
can happen while RCU read-side critical sections
use an outdated svc->scheduler pointer
- as planned, update_service is removed
- empty services can be freed immediately after grace period.
If dests were present, the services are freed from
the dest trash code
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
In previous commits the schedulers started to access
svc->destinations with _rcu list traversal primitives
because the IP_VS_WAIT_WHILE macro still plays the role of
grace period. Now it is time to finish the updating part,
i.e. adding and deleting of dests with _rcu suffix before
removing the IP_VS_WAIT_WHILE in next commit.
We use the same rule for conns as for the
schedulers: dests can be searched in RCU read-side critical
section where ip_vs_dest_hold can be called by ip_vs_bind_dest.
Some things are not perfect, for example, calling
functions like ip_vs_lookup_dest from updating code under
RCU, just because we use some function both from reader
and from updater.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This method releases the scheduler state,
it can not fail. Such change will help to properly
replace the scheduler in following patch.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
All dests will go to trash, no exceptions.
But we have to use new list node t_list for this, due
to RCU changes in following patches. Dests will wait there
initial grace period and later all conns and schedulers to
put their reference. The dests don't get reference for
staying in dest trash as before.
As result, we do not load ip_vs_dest_put with
extra checks for last refcnt and the schedulers do not
need to play games with atomic_inc_not_zero while
selecting best destination.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. As the weight for some
dest can be reduced during dest selection, change the
algorithm to check weights by using minimum weights in the
1 .. max_weight-(di-1) range, with the same step (di). By this
way we ensure that there will be always a weight >= 1 check
before claiming that all destinations are overloaded.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. As the previous entry
could be unlinked, limit the list traversals to 2 when
lookup started from previous entry.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. The read_lock for sched_lock is
removed. The set.lock is removed because now it is used in
rare cases, mostly under sched_lock.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. The read_lock for sched_lock is
removed. Use a dead flag to prevent new entries to be created
while scheduler is reclaimed. Use hlist for the hash table.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Use the new add_dest and del_dest methods
to reassign dests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs_dest_hold will be used under RCU lock
while ip_vs_dest_put can be called even after dest
is removed from service, as it happens for conns and
some schedulers.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Allow schedulers to use rcu_dereference when
returning destination on lookup. The RCU read-side critical
section will allow ip_vs_bind_dest to get dest refcnt as
preparation for the step where destinations will be
deleted without an IP_VS_WAIT_WHILE guard that holds the
packet processing during update.
Add new optional scheduler methods add_dest,
del_dest and upd_dest. For now the methods are called
together with update_service but update_service will be
removed in a following change.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The global list with schedulers ip_vs_schedulers
is accessed only from user context - configuration and
scheduler module [un]registration. Use ip_vs_sched_mutex
instead.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
We have many fields to set and few to reset,
use kmem_cache_alloc instead to save some cycles.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
__ip_vs_conn_in_get and ip_vs_conn_out_get are
hot places. Optimize them, so that ports are matched first.
By moving net and fwmark below, on 32-bit arch we can fit
caddr in 32-byte cache line and all addresses in 64-byte
cache line.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Convert __ip_vs_conntbl_lock_array as follows:
- readers that do not modify conn lists will use RCU lock
- updaters that modify lists will use spinlock_t
Now for conn lookups we will use RCU read-side
critical section. Without using __ip_vs_conn_get such
places have access to connection fields and can
dereference some pointers like pe and pe_data plus
the ability to update timer expiration. If full access
is required we contend for reference.
We add barrier in __ip_vs_conn_put, so that
other CPUs see the refcnt operation after other writes.
With the introduction of ip_vs_conn_unlink()
we try to reorganize ip_vs_conn_expire(), so that
unhashing of connections that should stay more time is
avoided, even if it is for very short time.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Allow the readers to use RCU lock and for
PE module registrations use global mutex instead of
spinlock. All PE modules need to use synchronize_rcu
in their module exit handler.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
rs_lock was used to protect rs_table (hash table)
from updaters (under global mutex) and readers (packet handlers).
We can remove rs_lock by using RCU lock for readers. Reclaiming
dest only with kfree_rcu is enough because the readers access
only fields from the ip_vs_dest structure.
Use hlist for rs_table.
As we are now using hlist_del_rcu, introduce in_rs_table
flag as replacement for the list_empty checks which do not
work with RCU. It is needed because only NAT dests are in
the rs_table.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
We use locks like tcp_app_lock, udp_app_lock,
sctp_app_lock to protect access to the protocol hash tables
from readers in packet context while the application
instances (inc) are [un]registered under global mutex.
As the hash tables are mostly read when conns are
created and bound to app, use RCU for readers and reclaim
app instance after grace period.
Simplify ip_vs_app_inc_get because we use usecnt
only for statistics and rely on module refcounting.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Currently when forwarding requests to real servers
we use dst_lock and atomic operations when cloning the
dst_cache value. As the dst_cache value does not change
most of the time it is better to use RCU and to lock
dst_lock only when we need to replace the obsoleted dst.
For this to work we keep dst_cache in new structure protected
by RCU. For packets to remote real servers we will use noref
version of dst_cache, it will be valid while we are in RCU
read-side critical section because now dst_release for replaced
dsts will be invoked after the grace period. Packets to
local real servers that are passed to local stack with
NF_ACCEPT need a dst clone.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Consolidate the PMTU checks, ICMP sending and
skb_dst modification in __ip_vs_get_out_rt and
__ip_vs_get_out_rt_v6. Now skb_dst is changed early
to simplify the transmitters.
Make sure update_pmtu is called only for local clients.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
We run in contexts like ip_rcv, ipv6_rcv, br_handle_frame,
do not expect shared skbs.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
After commit 70e7341673 (ipv4: Show that ip_send_reply()
is purely unicast routine.) we do not need to reroute DNAT-ed
traffic over loopback because reply uses iph daddr and not
rt_spec_dst.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Move and give better names to two functions:
- ip_vs_dst_reset to __ip_vs_dst_cache_reset
- __ip_vs_dev_reset to ip_vs_forget_dev
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
It was a bad idea to hide return statements in macros.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
The real server becomes unreachable on down event,
no need to wait device unregistration. Should help in
releasing dsts early before dst->dev is replaced with lo.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid replacing the cached route for real server
on every packet with different TOS. I doubt that routing
by TOS for real server is used at all, so we should be
better with such optimization.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Rename skb_dst_set_noref to __skb_dst_set_noref and
add force flag as suggested by David Miller. The new wrapper
skb_dst_set_noref_force will force dst entries that are not
cached to be attached as skb dst without taking reference
as long as provided dst is reclaimed after RCU grace period.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mutex initialization by allocation of the mailbox it protects.
introduced in commit 1d6f3cd89 'bnx2x: Prevent VF race'
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tokenring support was deleted in v3.5. One last holdout of the macro
CONFIG_TR escaped that fate. Until now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 40893fd(net: switch to use skb_probe_transport_header())
involes a new error accidently. When NET_SKBUFF_DATA_USES_OFFSE is
not enabled, below compile error happens:
CC net/packet/af_packet.o
net/packet/af_packet.c: In function ‘packet_sendmsg_spkt’:
net/packet/af_packet.c:1516:2: error: implicit declaration of function ‘skb_probe_transport_header’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [net/packet/af_packet.o] Error 1
make[1]: *** [net/packet] Error 2
make: *** [net] Error 2
As it seems skb_probe_transport_header() is not related to
NET_SKBUFF_DATA_USES_OFFSE, we should move the definition of
skb_probe_transport_header() out of scope of
NET_SKBUFF_DATA_USES_OFFSE macro.
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
yam_open has a redundant null check on null, it will
never be called with dev == NULL. Remove this redundant check.
This also cleans up a smatch warning:
drivers/net/hamradio/yam.c:869 yam_open() warn: variable
dereferenced before check 'dev' (see line 867)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
===================
this is a pull-request for net-next/master. It consists of three
patches by Lars-Peter Clausen to clean up the mcp251x spi-can driver,
two patches from Ludovic Desroches to bring device tree support to the
at91_can driver and a patch by me to fix a sparse warning in the
blackfin driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed
100 duplex full) with an ethernet cable plugged off, the mentioned algorithm
slows down a NIC speed, so further cable hook-up leads to nonoperable link state.
Signed-off-by: Kirill Kapranov <kapranoff@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
