pata_at91 driver is broken since faee0cc:
"make smc register base soc independent"
Fix it with newly introduced SMC accessors.
The overall action of removal of at91_sys_read/write will allow
to use the pata_at91 on a single zImage kernel.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-ide@vger.kernel.org
BF54x on-chip ATAPI controller allows maximum 0x1fffe bytes to be transfered
in one ATAPI transfer. So, set the max sg_tablesize to 4.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: Yutaka Ando <r46913@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
ahci: support the STA2X11 I/O Hub
pata_bf54x: fix BMIDE status register emulation
ata: add ata port hibernate callbacks
ata: update ata port's runtime status during system resume
[SCSI] runtime resume parent for child's system-resume
ahci: platform support for suspend/resume
libata-core: kill duplicate statement in ata_do_set_mode()
pata_of_platform: remove direct dependency on OF_IRQ
SATA/PATA: convert drivers/ata/* to use module_platform_driver()
pata_cs5536: forward port changes from cs5536
libata-sff: use ATAPI_{COD|IO}
ata: add ata port runtime PM callbacks
ata: add ata port system PM callbacks
[SCSI] sd: check runtime PM status in sd_shutdown
[SCSI] check runtime PM status in system PM
[SCSI] add flag to skip the runtime PM calls on the host
ata: make ata port as parent device of scsi host
ahci: start engine only during soft/hard resets
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
The AHCI controller found in the STA2X11 chip uses BAR number 0
instead of 5. Also, the chip's fixup code sets a special DMA mask
for all of its PCI functions, and the mask must be preserved here.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The author of this driver clearly wasn't familiar with the BMIDE specification
(also known as SFF-8038i) when he implemented the bmdma_status() method: first,
the interrupt bit of the BMIDE status register corresponds to nothing else but
INTRQ signal (ATAPI_DEV_INT here); second, the error bit is only set if the
controller encounters issue doing the bus master transfers, not on the IDE DMA
burst termination interrupts like here (moreover, setting the error bit doesn't
cause an interrupt). We now need to disable all those unused interrupts...
(The only thing I couldn't figure out is how to flush the FIFO to memory once
the interrupt happens as required by the mentioned spec.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.
This also fixes below warning during system suspend/resume.
WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()
4034 WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add platform hooks for custom suspend() and resume() functions. The
generic suspend/resume code in drivers/ata/ahci_platform.c is adapted
from the PCI version in drivers/ata/ahci.c.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit b3a706014e (libata: Add a
drivers/ide style DMA disable) neglected to remove the line in
ata_do_set_mode() it has obviously made useless/duplicated. Do this
now, and make a line added back then wrapped properly...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CONFIG_OF_IRQ is not available on some platforms and using of_irq_*
breaks the build. Since resources are already populated in the platform
device, get the irq from there instead.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts the drivers in drivers/ata/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Munaut <tnt@246tNt.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Mark Miesfeld <mmiesfeld@amcc.com>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Fix cable detection to also account for the slave device cable bit.
* Disable UDMA when programming MWDMA in cs5536_set_dmamode().
* Don't change UDMA settings in cs5536_set_piomode().
* Add cs5536_program_dtc() helper.
* Cleanup and uninline cs5536_[read,write]() methods.
Cc: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
atapi_pio_bytes() uses bare numbers for the ATAPI interrupt reason bits despite
these are #define'd in <linux/ata.h>.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change ata_host_request_pm to ata_port_request_pm which performs
port suspend/resume.
Add ata port type driver which implements port PM callbacks.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, the device tree of ata port and scsi host looks as below,
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
This patch makes ata port as parent device of scsi host, then it becomes
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is another attempt at fixing the same problem that 270dac35c2
(libata: ahci_start_engine compliant to AHCI spec) tried to solve.
Unfortunately, 270dac35c2 created regressions for a lot more common
controllers and got reverted.
This specific AHCI IP block becomes a brick if the DMA engine is
started while DRQ is set. It is not possible to avoid the condition
completely but the most common occurrence is caused by spurious use of
ahci_start_engine() from ahci_start_port() during init sequence.
DMA engine is started after both soft and hard resets and
ahci_start_port() is always followed by resets, so there is no reason
to start DMA engine from ahci_start_port().
This patch removes ahci_start_engine() invocation from
ahci_start_port(). This change makes failure path of
ahci_port_suspend() leave engine stopped without following resets.
This is resolved by replacing ahci_start_port() call with
ata_port_freeze() which forces resets afterwards, which is the better
behavior anyway.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
fix these errors:
drivers/ata/libata-sff.c:2538:3: error: implicit declaration of function
'ata_pci_bmdma_prepare_host'
drivers/ata/libata-sff.c:2549:40: error: 'ata_bmdma_interrupt'
undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The change in commit 904c04feaf "ahci_platform: Add the board_ids..."
doesn't work for the DT probing case as platform_get_device_id returns
NULL. Pick the default ahci_port_info in this case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Richard Zhu <richard.zhu@linaro.org>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Drivers should not use NO_IRQ; moreover, some architectures don't
have it nowadays. '0' is the 'no irq' case.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reenable sending SRST to devices connected behind a Sil3726 PMP.
This allow staggered spinups and handles drives that spins up slowly.
While the drives spin up, the PMP will not accept SRST.
Most controller reissues the reset until the drive is ready, while
some [Sil3124] returns an error.
In ata_eh_error, wait 10s before reset the ATA port and try again.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use dev_get_platdata() to retrieve the struct ahci_platform_data data
from the platform.
Signed-off-by: JiSheng Zhang <jszhang3@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add the documentation of parameters of ata_change_queue_depth to silence the warning of make xmldocs
Signed-off-by: Marcos paulo de Souza <marcos.mage@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in the ide dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include export.h explicitly now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Rename 'idetm_port' and 'idetm_data' variables to 'master_port'
and 'master_data' respectively to match register naming used in
efar_set_dmamode() and in ata_piix.c.
Fix efar_set_piomode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Besides making things noticably simpler it results in ~2% decrease in
the driver LOC count and also ~2% decrease in the driver binary size
(as measured on x86-32).
Fix piix_set_piomode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set SITRE (separate slave timing register) bit also in master-only
configurations to match other PIIX-alike drivers and make further
changes easier.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Always use ata_sff_data_xfer32() in ata_sff_data_xfer_noirq()
so the latter can be also used for host controllers supporting
32-bit PIO operations.
It is a completely safe thing to do because if 32-bit PIO is
not supported or enabled ata_sff_data_xfer32() will fallback
to a standard method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (aec62xx) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (sl82c105) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes IDE -> libata regression.
There shouldn't be any problems with it as corresponding IDE's host
driver (pdc202xx_new) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
