The driver "dwc-xlgmac" is dual-licensed.
Declare the dual license with MODULE_LICENSE().
Signed-off-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver "dwc-xlgmac" is dual-licensed. This patch adds
declaration of dual license in file headers.
Signed-off-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the driver feature distribution with the flow utilized
by the management firmware - first reserve L2 queues for
VFs and use all the remaining for the PF.
The current distribution might lead to PFs with an enormous
amount of queues, but at the same time leave us with insufficient
resources for starting all VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RoCE is enabled on a given L2 interface, the interrupt lines
are divided equally between L2 and RoCE -
But in case number of lines needed for RoCE is limited by number
of available CNQs, we can utilize the additional lines for L2.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware and driver are meant to be both backward and forward
compatibile with each other.
If a new mangement firmware would work with an older driver,
it's possible that driver would receive indications which are meaningless
to it. That's perfectly acceptible from the firmware part - so no need to
log such messages at default verbosity; That would only serve to confuse
users.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware is running on a Big Endian processor,
and when running on LE platform HW is configured to swap access
to memory shared between management firmware and driver on
32-bit granulariy.
As a result, for matters of simplicity most of the APIs between
driver and management firmware are based on 32-bit variables.
MAC settings are one exception, as driver needs to fill a byte
array when indicating to management firmware that primary MAC
has changed.
Due to the swap, driver must make sure that the mac that was
provided in byte-order would be translated into native order,
otherwise after the swap the management firmware would read
it swapped.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver interaction with management firmware involves a union
of all the data-members relating to the commands the driver prepares.
Current interface assumes the caller always passes such a union -
but thats cumbersome as well as risky [chancing a stack corruption
in case caller accidentally passes a smaller member instead of union].
Change implementation so that caller could pass a pointer to any
of the members instead of the union.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interaction of driver -> management firmware is based
on a one-pending mailbox [per interface], and various
mailbox commands need to be synchronized.
Current scheme is messy, and there's a difficulty extending
it as it deals differently with various commands as well as
making assumption on the required behavior for load/unload
requests.
Drop the current scheme into a completion-list-based approach;
Each flow would try sending the command when possible,
allowing one flow to complete another flow's completion and
relieve the mailbox before sending its own command.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning from unused set_complete variable. And rearrange code
to eliminate unnecessary goto's.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there already is a special case goto for control messages (skb == NULL)
in netvsc_send, there is no need for later checks in same code path.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channel inbound lock was not being used at all by the netvsc
device, but the spin_lock was helpful by providing necessary
barrier before waiting.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than a lock and variable, use a refcount_t to keep track
of the number of sub channels. Don't need to wait for subchannels
on device removal since wait was already done in device_add.
Also fix the error handling; don't wait forever in case of
an error on request to create sub channels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is cleaner to use RCU protected pointer (nvdev_ctx->nvdev)
to indicate device is in removed state, rather than having a separate
boolean flag. By using the pointer the context can be checked
by static checkers and dynamic lockdep.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc driver has an internal structure (netvsc_device) which
is created when device is opened and released when device is closed.
And also opened/released when MTU or number of channels change.
Since this is referenced in the receive and transmit path, it is
safer to use RCU to protect/prevent use after free problems.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default number of maximum channels should be limited to the
number of cpus available on the numa node of the primary channel.
This also makes sure maximum channels <= num_online_cpus
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device is not up, then changing MTU (or number of channels)
should not re-enable the device.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using NAPI, the single stream performance declined signifcantly
because the poll routine was updating host after every burst
of packets. This excess signalling caused host throttling.
This fix restores the old behavior. Host is only signalled
after the ring has been emptied.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are no egress packets pending, then don't look for tx completions
in napi poll. Also, fix broken tx queue wakeup logic.
Signed-off-by: VSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workqueue that is periodically run to try to allocate RX buffers in OOM
conditions in PF and VF.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed review comments from the previous patch-set.
- changed return value check of platform_get_irq() to < 0
- replaced devm_request(free)_irq() calls by request(free)_irq() since
they are called from open() and close()
- changed sizeof(struct mystruct) to sizeof(*mystruct)
- reduced indentation on tx_timeout()
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed port reset sequence by adding ECC init.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added phy management support by using phy abstraction layer APIs.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma operation mode configuration routine was wrongly moved to a
function (stmmac_mtl_configuration) that is only executed if the
core version is >= 4.00.
Fixes: 6deee2221e ("net: stmmac: prepare dma op mode config for multiple queues")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer need to keep the FW enabled for .ndo_close()
to work we can always stop FW after reconfiguration failure.
This seems to make most FWs more resilient to faults (at least
in error injection scenarios).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device open and close handlers check if the device is already
in the desired state. Thanks to our reconfig infrastructure
this should not be necessary, there doesn't seem to be any
code in the driver which depends on it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of ring full or DMA mapping error remember to flush xmit_more
delayed kicks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP6000 doesn't use queue pointers/doorbells for RX, it uses
'done' bit in descriptors. Remove the pointers from data structures.
Since we are saving space in rx_ring structure make fields we
previously compressed to 16bits word size again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning which was using netdev_warn() instead of dev_warn()
to early.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When acquiring an area fails we can't call function doing both
release and free.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core should detect when someone is trying to request an access
window which is too large for a given type of access. Otherwise
the requester will be put on a wait queue for ever without any
error message.
Add const qualifiers to clarify that we are only looking at read-
-only members in relevant functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When signal interrupts waiting for an area to become available
we assume success. Pay attention to the return code. Unpack
the code a little bit to make it more readable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
msleep_interruptible() returns time left to wait, not error
code. Return ERESTARTSYS when interrupted.
While at it correct a comment and make the polling a bit
more aggressive.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't access area_cache_list without its lock even
to check if it's empty.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document which fields of nfp_cpp are protected by which locks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After mutex cache removal we can put the mutex code in a separate
source file. This makes it clear it doesn't play with internals
of struct nfp_cpp any more.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPP mutex cache was introduced to work around the fact that the
same host could successfully acquire a lock multiple times. It
used to collapse multiple users to the same struct nfp_cpp_mutex
and track use count. Unfortunately it's racy. Since we now force
all nfp_mutex_lock() callers within the host to actually succeed
at acquiring the lock we no longer need the cache, let's remove it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global device lock is acquired to search the resource table.
The lock is actually itself part of the table (entry 0).
Therefore if someone asks for resource 0 we would deadlock since
double locking is no longer allowed.
Currently the driver doesn't try to lock that resource so let's
simply make sure we fail graciously and not add special handling
of this case until really need. Hide the relevant defines in
the source file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP can be connected to multiple machines via PCI or other buses.
Access to hardware resources is arbitrated using locks residing
in device memory. Currently nfpcore only respects the mutexes
when it comes to inter-host locking, but if we try to acquire
the same lock again, on one host - it will simply return success
because owner of the lock is already set to that host.
This makes the locks useless for arbitration within one host
and unfair because whichever host grabbed the lock will have
a chance to reacquire it without others getting a shot.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a610 ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_mapping_error() returns true if there is an error but we want
to return -ENOMEM and not 1.
Fixes: 65e0ace2c5 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mmd_phy_indirect() use the same terminology as the rest of the
code, making clear what each address is - phy address, devad, and
register number.
While here, remove the "inline" from this static function, leaving
it to the compiler to decide whether to inline this function, and
get rid of unnecessary parens.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert micrel to the new read_mmd/write_mmd driver methods. This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
