Current SRC (= Sampling Rate Converter) is supporting
SYNC mode and ASYNC mode. Current src.c cares SRC if FIN != FOUT.
Here, SYNC mode will be used for tweak, so it will be used
even FIN = FOUT. This patch enables SRC sync in such situation
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Yuichi Takagi <yuichi.takagi.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound SSIU has SSI_SYS_STATUS register whick will
be changed if over/under run was occurred.
Current rsnd driver is handling over/under run error on SSI/SRC,
but doesn't on SSIU.
HW guys can't guarantee correct behavior if it already had error bit
on status register when it start.
Thus, it should be cleared every start timing. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SCU_SYS_STATUSx is the register that writing 1 initializes the bit,
and writing 0 is ignored. So, it should use rsnd_mod_write()
instead of rsnd_mod_bset(), otherwise all bit will be cleared.
Thanks Shimoda-san
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen1 didn't have SSIU IP, and it was part of SRU.
In Gen2, SSIU was created and it has original register.
Let's cleanup rsnd_reg for SSIU, because this driver
doesn't support Gen1 SRU any more.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen1 support had been removed. "Gen2 only" comment is
no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is completely depends on CONFIG_OF
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
To fixup this issue, it should request/release DMA channel on each
playback/recorde timing.
But, DMA channel request/release function uses mutex lock inside.
This means it will breaks current spinlock's interrupt protect.
To solve this issue, DMA channel request/release function needs to
be called from non-spinlock area. This patch adds its callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmaen_start() is calling of_node_put() for np,
but it is not needed if it goes through this loop.
This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA mod is now connected to stream via rsnd_dai_connect().
This means DMA mod can use .remove for its clearance.
rsnd_dma_detach() is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will use DMA mode, and migh be fallback to PIO mode.
Using devm_request_irq() makes its operation more complex when
it fallbacks to PIO mode.
Let's use manual request_irq()/free_irq()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver is based on DeviceTree, and no one is
using this driver from non DT. Non-DT support is no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have for_each_rsnd_mod(), let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
rsnd_dai_call() is especially defined as very complex macro.
It is easier to read just a little bit by using for_each_rsnd_mod_xxx()
and new rsnd_status_update()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
In order to simplify this issue, this patch adds new rsnd_mod_next()
which is non-macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1a5658c213 ("ASoC: rsnd: count .probe/.remove for
rsnd_mod_call()") solved multi-resource-free issue, by putting
.probe/.remove under count control. But,it breaks sound mixing case
(if it was used under DPCM). In such case, it uses MIXn/DVCn/SSIn,
and these should be always probed.
This patch reverted above patch, and solved the same issue by
modifing _rsnd_kctrl_remove() function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX7pEPExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9Du
Fgf+MAOLDX8z7TbxAM4TnpPO7pRYF+wR+AWamVoUnHrq+gdsUkcKbnTlE8PP05Sp
VDf/ugCMcAQoYrrXPPiZLLB6YsJf2eXjlrTeF5eG/oHRC0mBeM/U6nHblNltFPKl
clV5jTm8Rq/I0AHAiYeTDetQsypK3eVjJ0PZLdenVWF+kL/+aTJ4GXIGgH27aSQC
7lwQZBRWfvGyE/IRu2NNXTPMNSaos/JtLh2/Y2qkWVEQ8YYwFxgRkfCRDHbFk2fK
8/mdWWlaBrApZN8t/RlJxo6rxuQGUn01HFvLpRK1N0EMuLWaTUFHQZtUV/KF/JSz
6Gj4tPLvDke0f4N2tIwoF9quXA==
=qgCG
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.9
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
The recent series of changes to the caching in the SSI driver have
caused a number of problems to appear in some test systems. These are
still not fully understood but we're coming up to the merge window so
for now let's revert commit 7de2763d9b (ASoC: fsl_ssi: Remove
.num_reg_defaults_raw from regmap_config) as backing that out seems to
resolve the problem on affected systems.
Reported-by: Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This hardware supports only 2-channel DAI, even mono ADC digital output
has two channels with the same data.
Having min_channels=1 results in broken playback of mono files in setups
where CPU DAI supports mono.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of STAC9766/9767, this driver includes wrong
usage of DECLARE_TLV_DB_LINEAR().
In "8.1.2. Master Volume Registers", attenuation of lineout volumes is
represented in 5 bits by -1.5 dB/step from 0 to -46.5 dB. Thus,
'master_tlv' should be dB step representation.
In "8.1.14. Record Gain", gain of volumes is represented in 4 bits by
1.5 dB/step from 0 to 22.5 dB. Thus, 'record_tlv' should be dB step
representation.
In "8.1.5. PC BEEP Volume", attenuation of volume is represented in 4 bits
by -3 dB/step from 0 to 45 dB. Thus, 'beep_tlv' should be dB step
representation.
In "8.1.7. Stereo or Mic Volume" and so on, gain of volumes is represented
in 5 bits by -1.5 dB from 12 to -34.5 dB. Thus, 'mix_tlv' should be dB
step representation.
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with
SNDRV_CTL_TLVD_DECLARE_DB_SCALE(), to give proper information to
applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
