This gets rid of all OVS specific VXLAN code in the receive and
transmit path by using a VXLAN net_device to represent the vport.
Only a small shim layer remains which takes care of handling the
VXLAN specific OVS Netlink configuration.
Unexports vxlan_sock_add(), vxlan_sock_release(), vxlan_xmit_skb()
since they are no longer needed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This factors out the device configuration out of the RTNL newlink
API which allows for in-kernel creation of VXLAN net_devices.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows putting a VXLAN device into a new flow-based mode in which
skbs with a ip_tunnel_info dst metadata attached will be encapsulated
according to the instructions stored in there with the VXLAN device
defaults taken into consideration.
Similar on the receive side, if the VXLAN_F_COLLECT_METADATA flag is
set, the packet processing will populate a ip_tunnel_info struct for
each packet received and attach it to the skb using the new metadata
dst. The metadata structure will contain the outer header and tunnel
header fields which have been stripped off. Layers further up in the
stack such as routing, tc or netfitler can later match on these fields
and perform forwarding. It is the responsibility of upper layers to
ensure that the flag is set if the metadata is needed. The flag limits
the additional cost of metadata collecting based on demand.
This prepares the VXLAN device to be steered by the routing and other
subsystems which allows to support encapsulation for a large number
of tunnel endpoints and tunnel ids through a single net_device which
improves the scalability.
It also allows for OVS to leverage this mode which in turn allows for
the removal of the OVS specific VXLAN code.
Because the skb is currently scrubed in vxlan_rcv(), the attachment of
the new dst metadata is postponed until after scrubing which requires
the temporary addition of a new member to vxlan_metadata. This member
is removed again in a later commit after the indirect VXLAN receive API
has been removed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit dfd8645ea1 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flags are used in the return path rather than the return patch.
Fixes: af33c1adae ("vxlan: Eliminate dependency on UDP socket in transmit path")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change remote checksum handling to set checksum partial as default
behavior. Added an iflink parameter to configure not using
checksum partial (calling csum_partial to update checksum).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vxlan transmit path there is no need to reference the socket
for a tunnel which is needed for the receive side. We do, however,
need the vxlan_dev flags. This patch eliminate references
to the socket in the transmit path, and changes VXLAN_F_UNSHAREABLE
to be VXLAN_F_RCV_FLAGS. This mask is used to store the flags
applicable to receive (GBP, CSUM6_RX, and REMCSUM_RX) in the
vxlan_sock flags.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VXLAN net_device looking for an appropriate socket may only consider
a socket which has a matching set of flags/extensions enabled. If
incompatible flags are enabled, return a conflict to have the caller
create a distinct socket with distinct port.
The OVS VXLAN port is kept unaware of extensions at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.
The group membership is defined by the lower 16 bits of skb->mark, the
upper 16 bits are used for flags.
SELinux allows to manage label to secure local resources. However,
distributed applications require ACLs to implemented across hosts. This
is typically achieved by matching on L2-L4 fields to identify the
original sending host and process on the receiver. On top of that,
netlabel and specifically CIPSO [1] allow to map security contexts to
universal labels. However, netlabel and CIPSO are relatively complex.
This patch provides a lightweight alternative for overlay network
environments with a trusted underlay. No additional control protocol
is required.
Host 1: Host 2:
Group A Group B Group B Group A
+-----+ +-------------+ +-------+ +-----+
| lxc | | SELinux CTX | | httpd | | VM |
+--+--+ +--+----------+ +---+---+ +--+--+
\---+---/ \----+---/
| |
+---+---+ +---+---+
| vxlan | | vxlan |
+---+---+ +---+---+
+------------------------------+
Backwards compatibility:
A VXLAN-GBP socket can receive standard VXLAN frames and will assign
the default group 0x0000 to such frames. A Linux VXLAN socket will
drop VXLAN-GBP frames. The extension is therefore disabled by default
and needs to be specifically enabled:
ip link add [...] type vxlan [...] gbp
In a mixed environment with VXLAN and VXLAN-GBP sockets, the GBP socket
must run on a separate port number.
Examples:
iptables:
host1# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
host2# iptables -I INPUT -m mark --mark 0x200 -j DROP
OVS:
# ovs-ofctl add-flow br0 'in_port=1,actions=load:0x200->NXM_NX_TUN_GBP_ID[],NORMAL'
# ovs-ofctl add-flow br0 'in_port=2,tun_gbp_id=0x200,actions=drop'
[0] https://tools.ietf.org/html/draft-smith-vxlan-group-policy
[1] http://lwn.net/Articles/204905/
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for remote checksum offload in VXLAN. This uses a
reserved bit to indicate that RCO is being done, and uses the low order
reserved eight bits of the VNI to hold the start and offset values in a
compressed manner.
Start is encoded in the low order seven bits of VNI. This is start >> 1
so that the checksum start offset is 0-254 using even values only.
Checksum offset (transport checksum field) is indicated in the high
order bit in the low order byte of the VNI. If the bit is set, the
checksum field is for UDP (so offset = start + 6), else checksum
field is for TCP (so offset = start + 16). Only TCP and UDP are
supported in this implementation.
Remote checksum offload for VXLAN is described in:
https://tools.ietf.org/html/draft-herbert-vxlan-rco-00
Tested by running 200 TCP_STREAM connections with VXLAN (over IPv4).
With UDP checksums and Remote Checksum Offload
IPv4
Client
11.84% CPU utilization
Server
12.96% CPU utilization
9197 Mbps
IPv6
Client
12.46% CPU utilization
Server
14.48% CPU utilization
8963 Mbps
With UDP checksums, no remote checksum offload
IPv4
Client
15.67% CPU utilization
Server
14.83% CPU utilization
9094 Mbps
IPv6
Client
16.21% CPU utilization
Server
14.32% CPU utilization
9058 Mbps
No UDP checksums
IPv4
Client
15.03% CPU utilization
Server
23.09% CPU utilization
9089 Mbps
IPv6
Client
16.18% CPU utilization
Server
26.57% CPU utilization
8954 Mbps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the header flags of VXLAN in anticipation of
defining some new ones:
- Move header related definitions from vxlan.c to vxlan.h
- Change VXLAN_FLAGS to be VXLAN_HF_VNI (only currently defined flag)
- Move check for unknown flags to after we find vxlan_sock, this
assumes that some flags may be processed based on tunnel
configuration
- Add a comment about why the stack treating unknown set flags as an
error instead of ignoring them
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not
other UDP-based encapsulation protocols where the format and size of the
header differs. This patch implements a generic ndo_gso_check() for
VXLAN which will only advertise GSO support when the skb looks like it
contains VXLAN (or no UDP tunnelling at all).
Implementation shamelessly stolen from Tom Herbert:
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added VXLAN link configuration for sending UDP checksums, and allowing
TX and RX of UDP6 checksums.
Also, call common iptunnel_handle_offloads and added GSO support for
checksums.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated.
The vxlan socket is openned into the i/o netns, ie into the netns where
encapsulated packets are received. The socket lookup is done into this netns to
find the corresponding vxlan tunnel. After decapsulation, the packet is
injecting into the corresponding interface which may stand to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Configuration example:
ip netns add netns1
ip netns exec netns1 ip link set lo up
ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
ip link set vxlan10 netns netns1
ip netns exec netns1 ip addr add 192.168.0.249/24 broadcast 192.168.0.255 dev vxlan10
ip netns exec netns1 ip link set vxlan10 up
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the burden from the NIC drivers to check if the
vxlan driver is enabled in the kernel and also makes available
the vxlan headrooms to them.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds two more ndo ops: ndo_add_rx_vxlan_port() and
ndo_del_rx_vxlan_port().
Drivers can get notifications through the above functions about changes
of the UDP listening port of VXLAN. Also, when physical ports come up,
now they can call vxlan_get_rx_port() in order to obtain the port number(s)
of the existing VXLAN interface in case they already up before them.
This information about the listening UDP port would be used for VXLAN
related offloads.
A big thank you to John Fastabend (john.r.fastabend@intel.com) for his
input and his suggestions on this patch set.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv6 support to vxlan device, as the new version
RFC already mentions it:
http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows more code sharing between vxlan and ovs-vxlan.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds data field to vxlan socket and export
vxlan handler api.
vh->data is required to store private data per vxlan handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
