A V4L2 driver for Renesas R-Car VIN driver that do not depend on
soc_camera. The driver is heavily based on its predecessor and aims to
replace it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:492:28: error: implicit
declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_TI_CAL also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Fixes: 343e89a792 ("[media] media: ti-vpe: Add CAL v4l2 camera capture driver")
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Timberdale FPGA video driver has not seen any real development
since 2011 (and very little before that).
One of the problems with the timblogiw driver is that it uses videobuf
instead of the newer vb2 framework. The long term goal is to either
convert or remove any driver still using videobuf. Since none of the
core v4l developers has the hardware, we cannot convert it ourselves.
As far as I can tell it was only used in an Intel demo board in 2009
using Meego:
http://www.chinait.com/intelcontent/intelprc/admin/PDFFile/20106411545.pdf
which has since been superseded.
Moving this driver to staging is the first step towards removal. After 2 or
3 kernel cycles it will be removed altogether unless someone steps up to
clean up this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Richard Röjfors <richard@puffinpack.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWt9V+AAoJEHm+PkMAQRiGvqUH/iKVFxRB+MpfwRteRv22gfxJ
8Y5jDuCt2qkePHieN5JoY4FqWIA+hR+UnctHBvOCLC7DNbY79yaYuWeuShfnRVw2
91Kspk2tgnWkjlZDZ273VNKAEveFYUdhHvHFUlItWubVIlzrKRGKdAcUpecQ33YD
IERr4VFxdQDgksGPzH2FLJwcAKilWWygQ9ATTsY0xJepTC6PwxAFxrNx5qPiqOoI
aHJBzczk50y9hHEPkYeeWloyzIZUmf81BCi/VwOsbB30q4ENwkS2MMnebhOmBjLp
g9Bml8m/Fk4N+h2vbcLj6Bu+rE+bYDZDZ2Fmbupy4NbEkng3x3iaTPkG+R2hErQ=
=IdcS
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rc3' into patchwork
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
The Camera Adaptation Layer (CAL) is a block which consists of a dual
port CSI2/MIPI camera capture engine.
Port #0 can handle CSI2 camera connected to up to 4 data lanes.
Port #1 can handle CSI2 camera connected to up to 2 data lanes.
The driver implements the required API/ioctls to be V4L2 compliant.
Driver supports the following:
- V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api
- Asynchronous sensor sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:484:2:
error: implicit declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_STI_BDISP also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sh-vou driver has been converted from videobuf to videobuf2, but
the Kconfig file still lists VIDEOBUF_DMA_CONTIG as a dependency.
Consequently we can build the driver without VIDEOBUF2_DMA_CONTIG
and get a link error:
drivers/built-in.o: In function `sh_vou_probe':
vf610-ocotp.c:(.text+0x2dbf5c): undefined reference to `vb2_dma_contig_init_ctx'
vf610-ocotp.c:(.text+0x2dc0b4): undefined reference to `vb2_dma_contig_cleanup_ctx'
vf610-ocotp.c:(.text+0x2dc144): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `sh_vou_remove':
vf610-ocotp.c:(.text+0x2dc190): undefined reference to `vb2_dma_contig_cleanup_ctx'
This changes the dependency to VIDEOBUF2_DMA_CONTIG instead.
Fixes: 57af3ad59d ("[media] sh-vou: convert to vb2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_STI_BDISP && VIDEO_RENESAS_JPU && VIDEO_DM365_VPFE && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’
VIDEO_RENESAS_JPU selects VIDEOBUF2_DMA_CONTIG, which bypasses its
dependency on HAS_DMA. Make VIDEO_RENESAS_JPU depend on HAS_DMA to fix
this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platforms using the OMAP3 ISP have all switched to DT, drop platform
data support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While this is the first DVB platform drivers, let's keep the
Kconfig options well organized, adding it on its own DVB menu.
Of course, it should depend on MEDIA_DIGITAL_TV_SUPPORT, as
this enables all DVB-related menus.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Here's the driver for the Renesas R-Car JPEG processing unit.
The driver is implemented within the V4L2 framework as a memory-to-memory
device. It presents two video nodes to userspace, one for the encoding part,
and one for the decoding part.
It was found that the only working mode for encoding is no markers output, so we
generate markers with software. In the current version of driver we also use
software JPEG header parsing because with hardware parsing performance is lower
than desired.
>From a userspace point of view the process is typical (S_FMT, REQBUF,
optionally QUERYBUF, QBUF, STREAMON, DQBUF) for both the source and destination
queues. STREAMON can return -EINVAL in case of mismatch of output and capture
queues format. Also during decoding driver can return buffers if queued
buffer with JPEG image contains image with inappropriate subsampling (e.g.
4:2:0 in JPEG and 4:2:2 in capture). If JPEG image and queue format dimensions
differ driver will return buffer on QBUF with VB2_BUF_STATE_ERROR flag.
During encoding the available formats are: V4L2_PIX_FMT_NV12M,
V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16, V4L2_PIX_FMT_NV16M for source and
V4L2_PIX_FMT_JPEG for destination.
During decoding the available formats are: V4L2_PIX_FMT_JPEG for source and
V4L2_PIX_FMT_NV12M, V4L2_PIX_FMT_NV16M, V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16
for destination.
Performance of current version:
1280x800 NV12 image encoding/decoding
decoding ~122 FPS
encoding ~191 FPS
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
This driver requires support for DMA attrs function, and not
just DMA. Change the options accordingly to remove those errors:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_free_nodes’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:132:3: error: implicit declaration of function ‘dma_free_attrs’ [-Werror=implicit-function-declaration]
dma_free_attrs(ctx->bdisp_dev->dev,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_alloc_nodes’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:157:9: error: implicit declaration of function ‘dma_alloc_attrs’ [-Werror=implicit-function-declaration]
base = dma_alloc_attrs(dev, node_size * MAX_NB_NODE, &paddr,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:157:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = dma_alloc_attrs(dev, node_size * MAX_NB_NODE, &paddr,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_alloc_filters’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:219:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = dma_alloc_attrs(dev, size, &paddr, GFP_KERNEL | GFP_DMA, &attrs);
Also, get rid of bogus, unused and duplicated symbol declaration
for the config option done at bdisp/Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This v4l2 mem2mem driver is a 2D blitter for STMicroelectronics SoC.
It uses the v4l2 mem2mem framework.
The following features are supported and tested:
- Color format conversion (RGB32, RGB24, RGB16, NV12, YUV420P)
- Copy
- Scale
- Flip
- Deinterlace
- Wide (4K) picture support
- Crop
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added missing slab.h include to bdisp-v4l2.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After adding virtio-gpu I get this funky kconfig dependency loop.
scripts/kconfig/conf --oldconfig Kconfig
drivers/video/fbdev/Kconfig:5:error: recursive dependency detected!
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:34: symbol DRM_KMS_FB_HELPER is selected by DRM_VIRTIO_GPU
drivers/gpu/drm/virtio/Kconfig:1: symbol DRM_VIRTIO_GPU depends on VIRTIO
drivers/virtio/Kconfig:1: symbol VIRTIO is selected by REMOTEPROC
drivers/remoteproc/Kconfig:4: symbol REMOTEPROC is selected by OMAP_REMOTEPROC
drivers/remoteproc/Kconfig:12: symbol OMAP_REMOTEPROC depends on OMAP_IOMMU
drivers/iommu/Kconfig:141: symbol OMAP_IOMMU is selected by VIDEO_OMAP3
drivers/media/platform/Kconfig:96: symbol VIDEO_OMAP3 depends on VIDEO_V4L2
drivers/media/v4l2-core/Kconfig:6: symbol VIDEO_V4L2 depends on I2C
drivers/i2c/Kconfig:7: symbol I2C is selected by FB_DDC
drivers/video/fbdev/Kconfig:59: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/fbdev/Kconfig:374: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/fbdev/Kconfig:362: symbol FB_CYBER2000 depends on FB
Making VIDEO_OMAP3 depend on OMAP_IOMMU instead of selecting it breaks the
loop, which looks like the best way to handle it to me. Updated OMAP_IOMMU
help text accordingly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Xilinx platforms have no hardwired video capture or video processing
interface. Users create capture and memory to memory processing
pipelines in the FPGA fabric to suit their particular needs, by
instantiating video IP cores from a large library.
The Xilinx Video IP core is a framework that models a video pipeline
described in the device tree and expose the pipeline to userspace
through the media controller and V4L2 APIs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The syscon register isn't part of the ISP, use it through the syscom driver
regmap instead. The syscom block is considered to be from 343x on ISP
revision 2.0 whereas 15.0 is assumed to have 3630 syscon.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_OMAP2_VOUT && VIDEO_VIU && VIDEO_TIMBERDALE) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `__videobuf_dc_free':
videobuf-dma-contig.c:(.text+0x6f4d32): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x6f4fe6): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x6f518e): undefined reference to `dma_free_coherent'
Commit 244829226f ("[media] timberdale: do not select TIMB_DMA")
dropped the dependency of VIDEO_TIMBERDALE on DMADEVICES, and thus the
implicit dependency on HAS_DMA. VIDEO_TIMBERDALE selects
VIDEOBUF_DMA_CONTIG, which bypasses its dependency on HAS_DMA. Make
VIDEO_TIMBERDALE depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.
As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.
Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.
Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The timberdale media driver requires the use of the respective
dma engine driver, but that may not be enabled, causing a
Kconfig warning:
warning: (VIDEO_TIMBERDALE) selects TIMB_DMA which has unmet direct dependencies (DMADEVICES && MFD_TIMBERDALE)
This fixes the dependency by removing the inappropriate 'select'
statement and replacing it with a direct dependency on the
drivers that provide the services this needs.
Fixes: 7155043c2d ("[media] enable COMPILE_TEST for media drivers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since we have to copy from input buffers into the bitstream ringbuffer
with the CPU, there is no need for contiguous DMA buffers on the decoder
input side.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds Video Processing Front End (VPFE) driver for
AM437X family of devices
Driver supports the following:
- V4L2 API using MMAP buffer access based on videobuf2 api
- Asynchronous sensor/decoder sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[hans.verkuil@cisco.com: swapped two lines to fix vpfe_release() & add pinctrl include]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that all platforms instantiate the VSP1 through DT, platform data
support isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
This is 1) *much* easier to type, and 2) is consistent with vivid
('vi' for virtual). More of such virtual drivers are planned, so keeping
the naming consistent makes sense.
Note that the old module name is retained as a module alias.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). However, there
are still some references to that symbol left, fix that by
substituting them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: <stable@vger.kernel.org> # for 3.17
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Renesas VSP1 Video Processing Engine support should be available
only on Renesas ARM SoCs.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vivid driver is a vastly superior test driver, so just drop the old
vivi driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Update the Kconfig and Makefile files so this driver can be compiled.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several arch-specific media drivers that don't
require asm-specific includes and can be successfully
compiled on x86. Add COMPILE_TEST dependency for them, in
order to allow a broader test on those drivers.
That helps static analysis tools like Coverity to discover
eventual troubles there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Allowing COMPILE_TEST here is trivial, but there's one missing
header to be added:
drivers/media/platform/ti-vpe/vpe.c: In function ‘vpe_probe’:
drivers/media/platform/ti-vpe/vpe.c:2266:56: error: ‘SZ_32K’ undeclared (first use in this function)
dev->base = devm_ioremap(&pdev->dev, dev->res->start, SZ_32K);
^
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
By allowing compilation on all archs, we can use static
analysis tools to test this driver.
In order to do that, replace asm/sizes.h by its generic
name (linux/sizes.h), with should keep doing the right
thing.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for jpeg codec on Exynos3250 SoC to
the s5p-jpeg driver. Supported raw formats are: YUYV, YVYU, UYVY,
VYUY, RGB565, RGB565X, RGB32, NV12, NV21. The support includes
also scaling and cropping features.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver uses the genalloc API, which doesn't have stubs in
case GENERIC_ALLOCATOR is disabled.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/built-in.o: In function `isp_video_open':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1253: undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `omap3isp_video_init':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1344: undefined reference to `vb2_dma_contig_init_ctx'
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1350: undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `omap3isp_video_cleanup':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1381: undefined reference to `vb2_dma_contig_cleanup_ctx'
make: *** [vmlinux] Error 1
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Attach an ARM DMA I/O virtual address space to the ISP device. This
switches to the IOMMU-aware ARM DMA backend, we can thus remove the
explicit calls to the OMAP IOMMU map and unmap functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDEO_TIMBERDALE selects TIMB_DMA which itself depends on
MFD_TIMBERDALE, so VIDEO_TIMBERDALE should either select or depend on
MFD_TIMBERDALE as well. I chose to make it depend on it because I
think it makes more sense and it is consistent with what other options
are doing.
Adding a "|| HAS_IOMEM" to the TIMB_DMA dependencies silenced the
kconfig warning about unmet direct dependencies but it was wrong:
without MFD_TIMBERDALE, TIMB_DMA is useless as the driver has no
device to bind to.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If NO_DMA=y:
warning: (VIDEO_DM6446_CCDC && VIDEO_DM355_CCDC && VIDEO_DM365_ISIF && VIDEO_OMAP2_VOUT && VIDEO_SH_VOU && VIDEO_VIU && VIDEO_TIMBERDALE && VIDEO_MX1 && VIDEO_OMAP1) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `videobuf_vm_close':
videobuf-dma-contig.c:(.text+0x407aa0): undefined reference to `videobuf_queue_cancel'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x407ba2): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x407d44): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `free_buffer':
sh_vou.c:(.text+0x41f73a): undefined reference to `videobuf_waiton'
drivers/built-in.o: In function `sh_vou_poll':
sh_vou.c:(.text+0x41f884): undefined reference to `videobuf_poll_stream'
drivers/built-in.o: In function `sh_vou_buf_prepare':
sh_vou.c:(.text+0x41fdf6): undefined reference to `videobuf_iolock'
drivers/built-in.o: In function `sh_vou_reqbufs':
sh_vou.c:(.text+0x4203b0): undefined reference to `videobuf_reqbufs'
drivers/built-in.o: In function `sh_vou_querybuf':
sh_vou.c:(.text+0x42040a): undefined reference to `videobuf_querybuf'
drivers/built-in.o: In function `sh_vou_qbuf':
sh_vou.c:(.text+0x42045e): undefined reference to `videobuf_qbuf'
drivers/built-in.o: In function `sh_vou_dqbuf':
sh_vou.c:(.text+0x4204c2): undefined reference to `videobuf_dqbuf'
drivers/built-in.o: In function `sh_vou_streamon':
sh_vou.c:(.text+0x420572): undefined reference to `videobuf_streamon'
drivers/built-in.o: In function `sh_vou_streamoff':
sh_vou.c:(.text+0x4205d2): undefined reference to `videobuf_streamoff'
drivers/built-in.o: In function `sh_vou_mmap':
sh_vou.c:(.text+0x420c46): undefined reference to `videobuf_mmap_mapper'
VIDEO_SH_VOU selects VIDEOBUF_DMA_CONTIG, which bypasses its dependency on
HAS_DMA. Make VIDEO_SH_VOU depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Running the coda driver without CONFIG_SRAM selected leads to the following
probe error:
coda 63ff4000.vpu: iram pool not available
coda: probe of 63ff4000.vpu failed with error -12
In order to avoid it, select CONFIG_SRAM inside VIDEO_CODA.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE is a block which consists of a single memory to memory path which
can perform chrominance up/down sampling, de-interlacing, scaling, and
color space conversion of raster or tiled YUV420 coplanar, YUV422
coplanar or YUV422 interleaved video formats.
We create a mem2mem driver based primarily on the mem2mem-testdev
example. The de-interlacer, scaler and color space converter are all
bypassed for now to keep the driver simple. Chroma up/down sampler
blocks are implemented, so conversion beteen different YUV formats is
possible.
Each mem2mem context allocates a buffer for VPE MMR values which it will
use when it gets access to the VPE HW via the mem2mem queue, it also
allocates a VPDMA descriptor list to which configuration and data
descriptors are added.
Based on the information received via v4l2 ioctls for the source and
destination queues, the driver configures the values for the MMRs, and
stores them in the buffer. There are also some VPDMA parameters like
frame start and line mode which needs to be configured, these are
configured by direct register writes via the VPDMA helper functions.
The driver's device_run() mem2mem op will add each descriptor based on
how the source and destination queues are set up for the given ctx, once
the list is prepared, it's submitted to VPDMA, these descriptors when
parsed by VPDMA will upload MMR registers, start DMA of video buffers on
the various input and output clients/ports.
When the list is parsed completely(and the DMAs on all the output ports
done), an interrupt is generated which we use to notify that the source
and destination buffers are done. The rest of the driver is quite
similar to other mem2mem drivers, we use the multiplane v4l2 ioctls as
the HW support coplanar formats.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
