Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending out multicast messages, the source address in inet->mc_addr is
ignored and rewritten by an autoselected one. This is caused by a typo in
commit 813b3b5db8 ("ipv4: Use caller's on-stack flowi as-is in output
route lookups").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the unreg_list and the close_list in dev_close_many preventing
dev_close_many from permuting the unreg_list. The permutations of the
unreg_list have resulted in cases where the loopback device is accessed
it has been freed in code such as dst_ifdown. Resulting in subtle memory
corruption.
This is the second bug from sharing the storage between the close_list
and the unreg_list. The issues that crop up with sharing are
apparently too subtle to show up in normal testing or usage, so let's
forget about being clever and use two separate lists.
v2: Make all callers pass in a close_list to dev_close_many
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation searches the whole DT for nodes named
"slave".
This patch changes it to search only child nodes for slaves.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we do not yet enable multiple PFs per port, it is possible
that a board will be reconfigured to enable them while the driver has
not yet been updated to fully support this.
The most obvious problem is that multiple functions may try to set
conflicting link settings. But we will also run into trouble if the
firmware doesn't consider us fully trusted. So, abort probing unless
both the LinkCtrl and Trusted flags are set for this function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The (inner) MTU of a ipip6 (IPv4-in-IPv6) tunnel cannot be set below 1280, which is the minimum MTU in IPv6.
However, there should be no IPv6 on the tunnel interface at all, so the IPv6 rules should not apply.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=15530
This patch allows to check the minimum MTU for ipv6 tunnel according to these rules:
-In case the tunnel is configured with ipip6 mode the minimum MTU is 68.
-In case the tunnel is configured with ip6ip6 or any mode the minimum MTU is 1280.
Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio wants to pass in cpumask_of(cpu), make parameter
const to avoid build warnings.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recognise the new Packet Memory and RX Data Path counters.
The following counters are added:
rx_pm_{trunc,discard}_bb_overflow - burst buffer overflowed. This should not
occur if BB correctly configured.
rx_pm_{trunc,discard}_vfifo_full - not enough space in packet memory. May
indicate RX performance problems.
rx_pm_{trunc,discard}_qbb - dropped by 802.1Qbb early discard mechanism.
Since Qbb is not supported at present, this should not occur.
rx_pm_discard_mapping - 802.1p priority configured to be dropped. This should
not occur in normal operation.
rx_dp_q_disabled_packets - packet was to be delivered to a queue but queue is
disabled. May indicate misconfiguration by the driver.
rx_dp_di_dropped_packets - parser-dispatcher indicated that a packet should be
dropped.
rx_dp_streaming_packets - packet was sent to the RXDP streaming bus, ie. a
filter directed the packet to the MCPU.
rx_dp_emerg_{fetch,wait} - RX datapath had to wait for descriptors to be
loaded. Indicates performance problems but not drops.
These are only provided if the MC firmware has the
PM_AND_RXDP_COUNTERS capability. Otherwise, mask them out.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Previously, efx_ef10_stat_mask returned a static const unsigned long[], which
meant that each possible mask had to be declared statically with
STAT_MASK_BITMAP. Since adding a condition would double the size of the
decision tree, we now create the bitmask dynamically.
To do this, we have two functions efx_ef10_raw_stat_mask, which returns a u64,
and efx_ef10_get_stat_mask, which fills in an unsigned long * argument.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The indices in nic_data->stats need to match the EF10_STAT_whatever
enum values. In efx_nic_update_stats, only mask; gaps are removed in
efx_ef10_update_stats.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Yuchung found following problem :
There are bugs in the SACK processing code, merging part in
tcp_shift_skb_data(), that incorrectly resets or ignores the sacked
skbs FIN flag. When a receiver first SACK the FIN sequence, and later
throw away ofo queue (e.g., sack-reneging), the sender will stop
retransmitting the FIN flag, and hangs forever.
Following packetdrill test can be used to reproduce the bug.
$ cat sack-merge-bug.pkt
`sysctl -q net.ipv4.tcp_fack=0`
// Establish a connection and send 10 MSS.
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+.000 bind(3, ..., ...) = 0
+.000 listen(3, 1) = 0
+.050 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+.000 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.001 < . 1:1(0) ack 1 win 1024
+.000 accept(3, ..., ...) = 4
+.100 write(4, ..., 12000) = 12000
+.000 shutdown(4, SHUT_WR) = 0
+.000 > . 1:10001(10000) ack 1
+.050 < . 1:1(0) ack 2001 win 257
+.000 > FP. 10001:12001(2000) ack 1
+.050 < . 1:1(0) ack 2001 win 257 <sack 10001:11001,nop,nop>
+.050 < . 1:1(0) ack 2001 win 257 <sack 10001:12002,nop,nop>
// SACK reneg
+.050 < . 1:1(0) ack 12001 win 257
+0 %{ print "unacked: ",tcpi_unacked }%
+5 %{ print "" }%
First, a typo inverted left/right of one OR operation, then
code forgot to advance end_seq if the merged skb carried FIN.
Bug was added in 2.6.29 by commit 832d11c5cd
("tcp: Try to restore large SKBs while SACK processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter updates for your net-next tree,
mostly ipset improvements and enhancements features, they are:
* Don't call ip_nest_end needlessly in the error path from me, suggested
by Pablo Neira Ayuso, from Jozsef Kadlecsik.
* Fixed sparse warnings about shadowed variable and missing rcu annotation
and fix of "may be used uninitialized" warnings, also from Jozsef.
* Renamed simple macro names to avoid namespace issues, reported by David
Laight, again from Jozsef.
* Use fix sized type for timeout in the extension part, and cosmetic
ordering of matches and targets separatedly in xt_set.c, from Jozsef.
* Support package fragments for IPv4 protos without ports from Anders K.
Pedersen. For example this allows a hash:ip,port ipset containing the
entry 192.168.0.1,gre:0 to match all package fragments for PPTP VPN
tunnels to/from the host. Without this patch only the first package
fragment (with fragment offset 0) was matched.
* Introduced a new operation to get both setname and family, from Jozsef.
ip[6]tables set match and SET target need to know the family of the set
in order to reject adding rules which refer to a set with a non-mathcing
family. Currently such rules are silently accepted and then ignored
instead of generating an error message to the user.
* Reworked extensions support in ipset types from Jozsef. The approach of
defining structures with all variations is not manageable as the
number of extensions grows. Therefore a blob for the extensions is
introduced, somewhat similar to conntrack. The support of extensions
which need a per data destroy function is added as well.
* When an element timed out in a list:set type of set, the garbage
collector skipped the checking of the next element. So the purging
was delayed to the next run of the gc, fixed by Jozsef.
* A small Kconfig fix: NETFILTER_NETLINK cannot be selected and
ipset requires it.
* hash:net,net type from Oliver Smith. The type provides the ability to
store pairs of subnets in a set.
* Comment for ipset entries from Oliver Smith. This makes possible to
annotate entries in a set with comments, for example:
ipset n foo hash:net,net comment
ipset a foo 10.0.0.0/21,192.168.1.0/24 comment "office nets A and B"
* Fix of hash types resizing with comment extension from Jozsef.
* Fix of new extensions for list:set type when an element is added
into a slot from where another element was pushed away from Jozsef.
* Introduction of a common function for the listing of the element
extensions from Jozsef.
* Net namespace support for ipset from Vitaly Lavrov.
* hash:net,port,net type from Oliver Smith, which makes possible
to store the triples of two subnets and a protocol, port pair in
a set.
* Get xt_TCPMSS working with net namespace, by Gao feng.
* Use the proper net netnamespace to allocate skbs, also by Gao feng.
* A couple of cleanups for the conntrack SIP helper, by Holger
Eitzenberger.
* Extend cttimeout to allow setting default conntrack timeouts via
nfnetlink, so we can get rid of all our sysctl/proc interfaces in
the future for timeout tuning, from me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on tcp listener refactoring, I found that it
would really make things easier if sock_common could include
the IPv6 addresses needed in the lookups, instead of doing
very complex games to get their values (depending on sock
being SYN_RECV, ESTABLISHED, TIME_WAIT)
For this to happen, I need to be sure that tcp6_timewait_sock
and tcp_timewait_sock consume same number of cache lines.
This is possible if we only use 32bits for tw_ttd, as we remove
one 32bit hole in inet_timewait_sock
inet_tw_time_stamp() is defined and used, even if its current
implementation looks like tcp_time_stamp : We might need finer
resolution for tcp_time_stamp in the future.
Before patch : sizeof(struct tcp6_timewait_sock) = 0xc8
After patch : sizeof(struct tcp6_timewait_sock) = 0xc0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows (optionally, via ethtool) the atl1e NIC to:
- Receive bad frames (runt, bad-fcs, etc..)
- Receive full frames without stripping the FCS.
This has been tested on my board by injecting runt and bad-fcs
frames with a FPGA-based device.
The particular scenario of receiving very short frames (<4 bytes)
without passing FCS to the upper layer has been also tested:
This could be potentially dangerous because the driver performs a
4 byte subtraction on the frame length, but I finally have NOT
added anything to avoid this because it seems the NIC always
discards frames so much short..
If someone still have some reason to worry about this, please
tell me.. I will add an explicit SW check..
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
0411,0241 RT5572 BUFFALO WI-U2-300D Wireless LAN Adapter
0789,0170 RT3572 Logitec LAN-W300AN/U2
0846,9013 RT3573 NETGEAR Adaptador USB Inalambrico Movistar
0df6,006e RT3573 Sitecom WiFi USB adapter N900
2001,3c1f RT3573 D-Link DWA-162 Wireless N900 Dual Band Adapter
2001,3c20 RT5372 D-Link DWA-140 Wireless N USB Adapter(rev.D)
2001,3c21 RT5572 D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.C)
2001,3c22 RT5372 D-Link DWA-132 Wireless N USB Adapter(rev.B)
2001,3c23 RT5372 D-Link GO-USB-N300 Wireless N Easy USB Adapter
2019,ab29 ? Planex GW-USMirco300
20f4,724a RT5572 TRENDnet N600 Wireless Dual Band USB Adapter
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rtl_phy_scan_operation_backup() exists, convert rtl8188ee to use it.
Routine rtl88e_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rtl_phy_scan_operation_backup() exists, convert rtl8723ae to use it.
Routine rtl8723ae_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rtl_phy_scan_operation_backup() exists, convert rtl8192de to use it.
Routine rtl92d_phy_scan_operation_backup() is no longer used and is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers rtl8192ce and rtl8192cu no longer rely on this routine. It is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rtl_phy_scan_operation_backup() exists, convert rtl8192ce to use it.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
Here is another batch of fixes intended for the 3.12 stream...
For the mac80211 bits, Johannes says:
"This time I have two fixes for IBSS (including one for wext, hah), a fix
for extended rates IEs, an active monitor checking fix and a sysfs
registration race fix."
On top of those...
Amitkumar Karwar brings an mwifiex fix for an interrupt loss issue
w/ SDIO devices. The problem was due to a command timeout issue
introduced by an earlier patch.
Felix Fietkau a stall in the ath9k driver. This patch fixes the
regression introduced in the commit "ath9k: use software queues for
un-aggregated data packets".
Stanislaw Gruszka reverts an rt2x00 patch that was found to cause
connection problems with some devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the routine exists in driver rtlwifi, convert rtl8192cu to use it.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several of the drivers supported by rtlwifi individually implement the same
routine that supports scans. As a first step, create this routine in
driver rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This completes removal of all places that reference variable 'noise'
in the rtl_stats struct. The definition of the struct is unchanged.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch lists the following:
CHECK drivers/net/wireless/rtlwifi/rtl8188ee/hw.c
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.
This info message is the result of a real error due to a missing break statement
in a "while (1)" loop.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch displays the following:
CHECK drivers/net/wireless/rtlwifi/usb.c
drivers/net/wireless/rtlwifi/usb.c:458 _rtl_usb_rx_process_agg() warn: assigning (-98) to unsigned variable 'stats.noise'
drivers/net/wireless/rtlwifi/usb.c:503 _rtl_usb_rx_process_noagg() warn: assigning (-98) to unsigned variable 'stats.noise'
drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/usb.c:596 _rtl_rx_get_padding() info: ignoring unreachable code.
The variable 'stats.noise' is not used, thus the initializers are removed.
The unreachable code info is fixed by including the appropriate section inside
#ifdef .. #endif constructions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch reports the following:
CHECK drivers/net/wireless/rtlwifi/pci.c
drivers/net/wireless/rtlwifi/pci.c:739 _rtl_pci_rx_interrupt() warn: assigning (-98) to unsigned variable 'stats.noise'
The variable 'stats.noise' is not used. That initializer is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch lists the following:
CHECK drivers/net/wireless/rtlwifi/rtl8192cu/trx.c
drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:367 _rtl_rx_process() warn: assigning (-98) to unsigned variable 'stats.noise'
This variable is unused, thus the initializer is removed, as well as a
comment referring to that variable.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch lists the following:
CHECK drivers/net/wireless/rtlwifi/rtl8192de/hw.c
drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8192de/hw.c:1200 rtl92de_set_qos() info: ignoring unreachable code.
The dead code is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for new RF chip ID: 3070. It seems to be the same as 5370,
maybe vendor just put wrong value on the eeprom, but add this id anyway
since devices with it showed on the marked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmfmac has common and bus specific part. The rx function api
was using sk_buff_head. Changed to sk_buff instead.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO firmware download routines uses one name for firmware file
and nvram file for all sdio devices. This is not user friendly.
Use fw filename and nvram filename based upon chip id and revision.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The definition of BRCMF_EVENTING_MASK_LEN results in a sparse
error message
.../fweh.c:331:22: error: bad constant expression
.../fweh.c:388:22: error: bad constant expression
.../dhd_common.c:256:22: error: bad constant expression
This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN
and it is used to allocate an array variable on the stack. Better
use DIV_ROUND_UP() macro.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bus layer need to share sk_buff::cb with firmware signal feature. Reserve
necessary memory so they won't overwrite each other.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Perform a valid check for core index to avoid illegal address access.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4339 is an a/b/g/n/ac 1x1 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update event list to keep sync with firmware development. Use calculated event
mask length instead of hard-coded value.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to cap ->msg_namelen or it leads to a buffer overflow when we
to the memcpy() in __audit_sockaddr(). It requires CAP_AUDIT_CONTROL to
exploit this bug.
The call tree is:
___sys_recvmsg()
move_addr_to_user()
audit_sockaddr()
__audit_sockaddr()
Reported-by: Jüri Aedla <juri.aedla@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix multi soft-interfaces setups with Network Coding enabled by
registering the CODED packet type once only (instead of once per soft-if)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=pqD/
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included change:
- fix multi soft-interfaces setups with Network Coding enabled by
registering the CODED packet type once only (instead of once per soft-if)
Signed-off-by: David S. Miller <davem@davemloft.net>
The Vortex driver works with PCI and Cardbus devices, not PCMCIA.
There never was an EISA 3c515 card, only ISA, so remove that option.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
