debugfs_remove has taken the IS_ERR into account. Just
remove the unnecessary condition.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.
Fixes: a2965f12fd ("r8169: remove rtl8169_set_speed_xmii")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Neil MacLeod <neil@nmacleod.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.
However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.
So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.
The issue has existed since route exceptions introduction.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Reported-by: ian.periam@dialogic.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic netlink family is only initialized during module init,
so it should be __ro_after_init like all other generic netlink
families.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was introduced to mlxsw in commit 7b81953066 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd36 ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed: Fix series for multi-function mode implementation.
The patch series addresses few issues in the switch dependent multi-function modes.
Please consider applying it to 'net' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to configure the DORQ to use vlan-id/priority for
roce EDPM.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:
mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000001165b000] [size=4096 bytes]
[mapped as page] [unmapped as single]
This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Avoid ELP information leak, by Sven Eckelmann
- Fix sysfs segfault issues, by Sven Eckelmann (2 patches)
- Fix locking when adding entries in various lists,
by Sven Eckelmann (5 patches)
- Fix refcount if queue_work() fails, by Marek Lindner (2 patches)
- Fixup forgotten version bump, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=B1qZ
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20180919' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
pull request for net: batman-adv 2018-09-19
here are some bugfixes which we would like to see integrated into net.
We forgot to bump the version number in the last round for net-next, so
the belated patch to do that is included - we hope you can adopt it.
This will most likely create a merge conflict later when merging into
net-next with this rounds net-next patchset, but net-next should keep
the 2018.4 version[1].
[1] resolution:
--- a/net/batman-adv/main.h
+++ b/net/batman-adv/main.h
@@ -25,11 +25,7 @@
#define BATADV_DRIVER_DEVICE "batman-adv"
#ifndef BATADV_SOURCE_VERSION
-<<<<<<<
-#define BATADV_SOURCE_VERSION "2018.3"
-=======
#define BATADV_SOURCE_VERSION "2018.4"
->>>>>>>
#endif
/* B.A.T.M.A.N. parameters */
Please pull or let me know of any problem!
Here are some batman-adv bugfixes:
- Avoid ELP information leak, by Sven Eckelmann
- Fix sysfs segfault issues, by Sven Eckelmann (2 patches)
- Fix locking when adding entries in various lists,
by Sven Eckelmann (5 patches)
- Fix refcount if queue_work() fails, by Marek Lindner (2 patches)
- Fixup forgotten version bump, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang says:
====================
ipv6: fix issues on accessing fib6_metrics
The latest fix on the memory leak of fib6_metrics still causes
use-after-free.
This patch series first revert the previous fix and propose a new fix
that is more inline with ipv4 logic and is tested to fix the
use-after-free issue reported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When dst->_metrics and f6i->fib6_metrics share the same memory, both
take reference count on the dst_metrics structure. However, when dst is
destroyed, ip6_dst_destroy() only invokes dst_destroy_metrics_generic()
which does not take care of READONLY metrics and does not release refcnt.
This causes memory leak.
Similar to ipv4 logic, the fix is to properly release refcnt and free
the memory space pointed by dst->_metrics if refcnt becomes 0.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a network interface is created prior to the SFP socket being
available, ethtool can request module information. This unfortunately
leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc
Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: fixes 2018-09-18
here are some fixes in different areas of the smc code for the net
tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. kernel_sendmsg can return a negative
error code.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't check a listen socket for pending urgent data in smc_poll().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a linkgroup is terminated abnormally already due to failing
LLC CONFIRM LINK or LLC ADD LINK, fallback to TCP is still possible.
In this case do not switch to state SMC_PEERABORTWAIT and do not set
sk_err.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a failing smc_listen_rdma_finish() smc_listen_decline() is
called. If fallback is possible, the new socket is already enqueued
to be accepted in smc_listen_decline(). Avoid enqueuing a second time
afterwards in this case, otherwise the smc_create_lgr_pending lock
is released twice:
[ 373.463976] WARNING: bad unlock balance detected!
[ 373.463978] 4.18.0-rc7+ #123 Tainted: G O
[ 373.463979] -------------------------------------
[ 373.463980] kworker/1:1/30 is trying to release lock (smc_create_lgr_pending) at:
[ 373.463990] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc]
[ 373.463991] but there are no more locks to release!
[ 373.463991]
other info that might help us debug this:
[ 373.463993] 2 locks held by kworker/1:1/30:
[ 373.463994] #0: 00000000772cbaed ((wq_completion)"events"){+.+.}, at: process_one_work+0x1ec/0x6b0
[ 373.464000] #1: 000000003ad0894a ((work_completion)(&new_smc->smc_listen_work)){+.+.}, at: process_one_work+0x1ec/0x6b0
[ 373.464003]
stack backtrace:
[ 373.464005] CPU: 1 PID: 30 Comm: kworker/1:1 Kdump: loaded Tainted: G O 4.18.0-rc7uschi+ #123
[ 373.464007] Hardware name: IBM 2827 H43 738 (LPAR)
[ 373.464010] Workqueue: events smc_listen_work [smc]
[ 373.464011] Call Trace:
[ 373.464015] ([<0000000000114100>] show_stack+0x60/0xd8)
[ 373.464019] [<0000000000a8c9bc>] dump_stack+0x9c/0xd8
[ 373.464021] [<00000000001dcaf8>] print_unlock_imbalance_bug+0xf8/0x108
[ 373.464022] [<00000000001e045c>] lock_release+0x114/0x4f8
[ 373.464025] [<0000000000aa87fa>] __mutex_unlock_slowpath+0x4a/0x300
[ 373.464027] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc]
[ 373.464029] [<0000000000197a68>] process_one_work+0x2a8/0x6b0
[ 373.464030] [<0000000000197ec2>] worker_thread+0x52/0x410
[ 373.464033] [<000000000019fd0e>] kthread+0x15e/0x178
[ 373.464035] [<0000000000aaf58a>] kernel_thread_starter+0x6/0xc
[ 373.464052] [<0000000000aaf584>] kernel_thread_starter+0x0/0xc
[ 373.464054] INFO: lockdep is turned off.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In state SMC_INIT smc_poll() delegates polling to the internal
CLC socket. This means, once the connect worker has finished
its kernel_connect() step, the poll wake-up may occur. This is not
intended. The wake-up should occur from the wake up call in
smc_connect_work() after __smc_connect() has finished.
Thus in state SMC_INIT this patch now calls sock_poll_wait() on the
main SMC socket.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: nvm_param.dir_type may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJboCdPAAoJEEg/ir3gV/o+OqQH/2U2kCMUHRuG6WGEbm+bTz7m
fF2L1iRMeXvpmD0FrWs1XiBEg1/6Gf6GfNLmuwRqhHJMi/ok1310V5UbQ3dcXEQ5
7rIzBUbd2jyrI5wln9ISgmvgi/r7Cdzf9xNM3MHmPCouNWxbX85VLTGdTXcsUknd
Z7lZHbPjB8aeZEBmeQdNbGvwZOe9IIgTlfEN4gwrYvUtJD82HrGgGpdLvnSWgy4X
RhKdjvhkYx5ba3AH9CbY88oR5LRjhk3dGhngpMDvQZBmqE0W0j8tXkR8bj36zJN6
m2YJadeGlds7fubFORYaaDGuPBtCT5SnrJqboEMZ8fzuJMqdyvBNI/LtTRTIGAc=
=FOdR
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-09-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-09-17
Sorry about the previous submission of this series which was mistakenly
marked for net-next, here I am resending with 'net' mark.
This series provides three fixes to mlx5 core and mlx5e netdevice
driver.
Please pull and let me know if there's any problem.
For -stable v4.16:
('net/mlx5: Check for SQ and not RQ state when modifying hairpin SQ')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to ETSI TS 102 622 specification chapter 4.4 pipe identifier
is 7 bits long which allows for 128 unique pipe IDs. Because
NFC_HCI_MAX_PIPES is used as the number of pipes supported and not
as the max pipe ID, its value should be 128 instead of 127.
nfc_hci_recv_from_llc extracts pipe ID from packet header using
NFC_HCI_FRAGMENT(0x7F) mask which allows for pipe ID value of 127.
Same happens when NCI_HCP_MSG_GET_PIPE() is being used. With
pipes array having only 127 elements and pipe ID of 127 the OOB memory
access will result.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Allen Pais <allen.pais@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling SHDLC I-Frame commands "pipe" field used for indexing
into an array should be checked before usage. If left unchecked it
might access memory outside of the array of size NFC_HCI_MAX_PIPES(127).
Malformed NFC HCI frames could be injected by a malicious NFC device
communicating with the device being attacked (remote attack vector),
or even by an attacker with physical access to the I2C bus such that
they could influence the data transfers on that bus (local attack vector).
skb->data is controlled by the attacker and has only been sanitized in
the most trivial ways (CRC check), therefore we can consider the
create_info struct and all of its members to tainted. 'create_info->pipe'
with max value of 255 (uint8) is used to take an offset of the
hdev->pipes array of 127 elements which can lead to OOB write.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Allen Pais <allen.pais@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Kevin Deus <kdeus@google.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup function uses "$CMD 2 > /dev/null", which doesn't actually
send stderr to /dev/null, so when the netns doesn't exist, the error
message is shown. Use "2> /dev/null" instead, so that those messages
disappear, as was intended.
Fixes: d1f1b9cbf3 ("selftests: net: Introduce first PMTU test")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Coalesce and tail addr fixes
The fix for coalesce timer and a fix in tail address setting that impacts
XGMAC2 operation.
The series is:
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
on a113 s400 board (single queue)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: f748be531d ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave writes:
"Various fixes, all over the place:
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
DST_NOCOUNT in dst_entry::flags tracks whether the entry counts
toward route cache size (net->ipv6.sysctl.ip6_rt_max_size).
If the flag is NOT set, dst_ops::pcpuc_entries counter is incremented
in dist_init() and decremented in dst_destroy().
This flag is tied to allocation/deallocation of dst_entry and
should not be copied from another dst/route. Otherwise it can happen
that dst_ops::pcpuc_entries counter grows until no new routes can
be allocated because the counter reached ip6_rt_max_size due to
DST_NOCOUNT not set and thus no counter decrements on gc-ed routes.
Fixes: 3b6761d18b ("net/ipv6: Move dst flags to booleans in fib entries")
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede says:
====================
r8169 (x86) clk fixes to fix S0ix not being reached
This series adds code to the r8169 ethernet driver to get and enable an
external clock if present, avoiding the need for a hack in the
clk-pmc-atom driver where that clock was left on continuesly causing x86
some devices to not reach deep power saving states (S0ix) when suspended
causing to them to quickly drain their battery while suspended.
The 3 commits in this series need to be merged in order to avoid
regressions while bisecting. The clk-pmc-atom driver does not see much
changes (it was last touched over a year ago). So the clk maintainers
have agreed with merging all 3 patches through the net tree.
All 3 patches have Stephen Boyd's Acked-by for this purpose.
This v2 of the series only had some minor tweaks done to the commit
messages and is ready for merging through the net tree now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d31fd43c0f ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.
This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).
This is related to commit d31fd43c0f ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.
This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d31fd43c0f ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.
This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel SoC was prevented from entering lower idle state because
of RTL8106E's ASPM was not enabled.
So enable ASPM on RTL8106E (chip version 39).
Now the Intel SoC can enter lower idle state, power consumption and
temperature are much lower.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a small delay after setting ASPM in vendor drivers, r8101 and
r8168.
In addition, those drivers enable ASPM before ClkReq, also change that
to align with vendor driver.
I haven't seen anything bad becasue of this, but I think it's better to
keep in sync with vendor driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes kcm users know they need to look for the
strparser offset within their bpf program, which is not documented
anywhere and examples laying around do not do.
The actual recv function does handle the offset well, so we can create a
temporary clone of the skb and pull that one up as required for parsing.
The pull itself has a cost if we are pulling beyond the head data,
measured to 2-3% latency in a noisy VM with a local client stressing
that path. The clone's impact seemed too small to measure.
This bug can be exhibited easily by implementing a "trivial" kcm parser
taking the first bytes as size, and on the client sending at least two
such packets in a single write().
Note that bpf sockmap has the same problem, both for parse and for recv,
so it would pulling twice or a real pull within the strparser logic if
anyone cares about that.
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When modifying hairpin SQ, instead of checking if the next state equals
to MLX5_SQC_STATE_RDY, we compare it against the MLX5_RQC_STATE_RDY enum
value.
The code worked since both of MLX5_RQC_STATE_RDY and MLX5_SQC_STATE_RDY
have the same value today.
This patch fixes this issue.
Fixes: 18e568c390 ("net/mlx5: Hairpin pair core object setup")
Change-Id: I6758aa7b4bd137966ae28206b70648c5bc223b46
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use accessor function READ_ONCE to read from coherent memory modified
by the device and read by the driver. This becomes most important in
preemptive kernels where cond_resched implementation does not have the
side effect which guaranteed the updated value.
Fixes: 269d26f47f ("net/mlx5: Reduce command polling interval")
Change-Id: Ie6deeb565ffaf76777b07448c7fbcce3510bbb8a
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
