This patch fixes an issue where we check for irq's disabled then exit after
explicitly disabling them with spin_lock_irqsave.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can enable the use of build_skb for cases
where jumbo frames are disabled. The advantage to this is that we do not
have to perform a memcpy to populate the header and as a result we see a
significant performance improvement.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTM_GETLINK dump the vlan filter list of a given
bridge port. The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe set gso_size but not gso_type. This leads to
crashes in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects the fact that we were using 1522 to test for the
max frame size in ixgbe_change_mtu and 1518 in ixgbe_set_vf_lpe. The
difference was the addition of VLAN_HLEN which we only need to add in the case
of computing a buffer size, but not a filter size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the rval variable returns from function and replaces
them with direct returns in ixgbe_dcbnl_getnumtcs. It also changes how
ixgbe_gstrings_test is copied into data with memcpy in ixgbe_get_strings
because "*ixgbe_gstrings_test too small (32 vs 160)".
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a default case which goes to the next loop iteration
in the case where p is not set, preventing p from being dereferenced.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.
Based on original patch from Aurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines, function prototypes and data types which are applicable to
all/most devices supported by the driver but are specific to the
manageability component of each device to the new manage.h header file.
These #defines, function prototypes and data types can be used by other
files in the driver and moving them to the manageability-specific file
makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the NVM component of
each device to the new nvm.h header file. These #defines and function
prototypes can be used by other files in the driver and moving them to the
NVM-specific file makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the PHY component of
each device to the new phy.h header file. These function prototypes can be
used by other files in the driver and moving them to the PHY-specific file
makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move prototypes for functions which are applicable to all/most devices
supported by the driver and are specific to the MAC component of each
device to the new mac.h header file. These function prototypes can be used
by other files in the driver and moving them to the MAC-specific file makes
it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names). These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines specific to the ESB2/82563 family of devices to the new
80003es2lan.h header file. These defines can be used by other files in the
driver and moving them to the 80003es2lan-family-specific file makes it
clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names). These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions. Use those instead of redundant local
defines.
Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).
Some whitespace issues in the surrounding context of the above changes are
also cleaned up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the unused parameter when possible, otherwise use __always_unused
attribute.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For clarity, wrap OR'ed bit settings with parentheses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant defines which are defined elsewhere.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the autoneg parameter from the setup_link functions.
Adds local variable autoneg to setup_link functions to be passed
to get_link_capabilities functions if needed.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Removes the autoneg parameter from the setup_link_speed functions. These
functions do nothing with this parameter.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device lookup neglected to do a pci_dev_put() to decrement the
device reference count.
Reported-by: Elena Gurevich <elena.gurevich@toganetworks.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for up2tc change and call ixgbe_dcbnl_devreset() if the mapping has
changed but the number of TC's in use has not changed.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tighten up some of the code surrounding MAC addresses. Since the PF is
now giving all zeros instead of a random address, check for this case
and generate a random address. This ensures that we always know when we
have a random address and udev won't get upset about it.
Additionally, tighten up some of the log messages and clean up the
formatting.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change makes it necessary to set get_link_status to ensure that
the driver fetches the correct, refreshed value for link status and speed
when it has changed in the physical function device.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was removed but the applicable comments were not.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary #include, forward prototype of struct e1000_adapter and
an empty comment; fix a comment which mentions "static data for the MAC"
which is not applicable to the following struct; and cleanup some
whitespace issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All references to E1000_ERT_2048 have been removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this. To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call. The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used. A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...and cleanup some whitespace in other prototypes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver has been converted to use extended descriptors instead of
the older legacy descriptor type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults. This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the i217 and i218 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register. Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 can link at 100Mbps - fix the link speed indicator message to
show that value.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63. Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for enable/disable of SR-IOV via the PCI sysfs interface
move some core SR-IOV enablement code that would be common to module
parameter usage or callback from the PCI bus driver to a separate
function so that it can be used by either method.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally. Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to inline the Rx PTP descriptor handling. The main
motivation is to avoid unnecessary jumps into function calls that we then
immediately exit because we are not performing timestamps.
The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU
utilization in my performance runs to 0%, and the only value tested is the Rx
descriptor which should already be warm in the cache if not stored in a
register.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.
This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.
To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.
If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the comment on ptp_overflow_check to match up with what is
currently used as the parameters. Also change the jiffies check to use
time_is_after_jiffies macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the filters for ethtool's get_ts_info to return support for
all filters which can be supported by upscaling to ptp_v2_event. The intent
behind this change is due to reasoning that we do in fact support the
filters. (hwtstamp_ioctl returns success after setting the filter to the
upscaled version). In this way we can remain consistent over which filters are
supported via the get_ts_info ioctl and which filters are in practice actually
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the ethtool diagnostics test by ensuring that the tests
work properly regardless of what state the adapter was in. The SRIOV VF check is
done at the beginning, forgoing the link test. The if_running -> dev_close is
moved before the link test, as well as a call to enable the Tx laser. This
ensures that the link test will return valid results even when adapter was
previously down. Also, a call to disable the Tx laser is added if the device
was down before the start. This ensures consistent behavior of the Tx laser
before and after the diagnostic checks. The end result is consistent behavior
regardless of device state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates Copyright year to 2013
v2: Changed Copyright year on Makefile
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the physical function (PF) is reset for any reason the statistics
collection in ixgbevf_update_stats needs to wait to update until after
the reset synchronization ensures that the PF driver is up and running
and is finished with its own reset. Go ahead and clear the link flag to
indicate this when the control message from the PF is received. The
reset synchronization and recovery in the watchdog task will eventually
set the link flag up when the PF has resumed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dev_info to log link up/down messages.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts. The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map. To do this I have expanded the work done in the main loop by
pushing first into tx_buffer. This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor. The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo. By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.
To do this I also needed to change the logic and/or drop some flags. I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do. Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb. Instead we can just check the bitflag in the skb.
In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway. Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads. Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.
With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than use an extra #define for something that already exists, use the
kernel #define for the PTP port.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent a race condition where an skb has been saved to return the Tx
timestamp later and the driver is removed, add a check to determine if we
have an skb stored and, if so, free it.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check against possible Rx timestamp freezing in the hardware via
watchdog mechanism. This situation can occur when an Rx timestamp has been
latched, but the packet has been dropped because the Rx ring is full.
Whenever a packet comes in that should be timestamped, the Rx timestamp
gets latched into the hardware registers and we will store the jiffy value
in the rx_ring. The watchdog will keep track of his own jiffy timer
whenever there is no valid timestamp in the registers.
If the watchdog detects a valid timestamp in the registers, meaning that no
Rx packet has consumed it yet, it will check which time is most recent: the
last time in the watchdog or any time in the rx_rings. If the most recent
"event" was more than 5 seconds ago, it will flush the Rx timestamp and
print a warning message to the syslog.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When transmitting a packet that must return a Tx timestamp, a work item
gets scheduled to poll for the Tx timestamp being completed in hardware.
Add a timeout on this work item of 15 seconds from when the driver gets the
skb, after which it will stop polling. Report via stats and system log if
this occurs.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable SW timestamping for situations where the user may prefer it over HW
timestamping or there may not be HW timestamping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have internal sensors that report thermal data. This
patch enables reporting of that data via sysfs.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our devices have internal sensors for reporting thermal data.
This patch creates the interface to the sensors for exporting via sysfs.
Subsequent patch will actually export the data.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have sensors on them accessible via i2c and a private
interface. This patch implements the kernel interface for i2c to those sensors.
Subsequent patches will provide functions to export that data.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set. Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the standard #defines for PCIe Capability ASPM fields.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
