This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: Sylwester Nawrocki <snjw23@gmail.com>
CC: Piotr Chmura <chmooreck@poczta.onet.pl>
CC: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The as102 driver can be converted to use module_usb_driver() which saves
a lot of code, and gets rid of an unwanted err() call at the same time.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Sylwester Nawrocki <snjw23@gmail.com>
Cc: Piotr Chmura <chmooreck@poczta.onet.pl>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead
Cc: Jarod Wilson <jarod@wilsonet.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead
Cc: Jarod Wilson <jarod@wilsonet.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Andrew Miller <amiller@amilx.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Cc: Jarod Wilson <jarod@wilsonet.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If, in drivers/staging/media/as102/as102_fw.c::as102_fw_upload(), the call
cmd_buf = kzalloc(MAX_FW_PKT_SIZE, GFP_KERNEL);
should fail and return NULL so that we jump to the 'error:' label,
then we'll end up calling 'release_firmware(firmware);' with
'firmware' still uninitialized - not good.
The easy fix is to just initialize 'firmware' to NULL when we declare
it, since release_firmware() deals gracefully with being passed NULL
pointers.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- V4L2 API additions to better support JPEG compression control
- media API additions to properly support MPEG decoders
- V4L2 API additions for image crop/scaling
- a few other V4L2 API DocBook fixes/improvements
- two new DVB frontend drivers: m88rs2000 and rtl2830
- two new DVB drivers: az6007 and rtl28xxu
- a framework for ISA drivers, that removed lots of common code found
at the ISA radio drivers
- a new FM transmitter driver (radio-keene)
- a GPIO-based IR receiver driver
- a new sensor driver: mt9m032
- some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
vs6624
- several new board additions, driver fixes, improvements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
[media] update CARDLIST.em28xx
[media] partially reverts changeset fa5527c
[media] stb0899: fix the limits for signal strength values
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
[media] -EINVAL -> -ENOTTY
[media] gspca - sn9c20x: Cleanup source
[media] gspca - sn9c20x: Simplify register write for capture start/stop
[media] gspca - sn9c20x: Add automatic JPEG compression mechanism
[media] gspca - sn9c20x: Greater delay in case of sensor no response
[media] gspca - sn9c20x: Optimize the code of write sequences
[media] gspca - sn9c20x: Add the JPEG compression quality control
[media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
[media] gspca - sn9c20x: Propagate USB errors to higher level
[media] gspca - sn9c20x: Use the new video control mechanism
[media] gspca - sn9c20x: Fix loss of frame start
[media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
[media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
...
linux-next:
I like to spend some time reading code, in doing so I have found some
typos in some of the comments.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ryley and me tested several eLNA configuration values with both a rooftop
and a portable antenna.
Ryley fuond out that the best value for his Elgato stick is indeed the current
default value 0xC0.
Instead, my stick is not capable of tuning VHF channels with 0xC0. With 0x80,
VHF works but the tuner sensitivity with the portable antenna is poor.
Instead, the value 0xA0 works with VHF and also gives good performance with
both the rooftop and the portable antenna.
So we concluded that devices built on the reference design work best with 0xA0,
while custom designs (Elgato, PCTV) seem to require 0xC0.
I also removed the unused parameter "minor" in struct as102_dev_t.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Ryley Angus <rangus@student.unimelb.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a regression in kernel 3.3 due to this patch:
http://patchwork.linuxtv.org/patch/8332/
That patch changes "#pragma pack(1)" with "__packed" attributes, but it is not
complete. In fact, in the as102 driver there are a lot of structs/unions
defined inside other structs/unions.
When the "__packed" attribute is applied only on the external struct, it will
not affect the internal struct definitions.
So the regression is fixed by specifiying the "__packed" attribute also on the
internal structs.
This patch should go into 3.3, as it fixes a regression introduced in the new
kernel version.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Ryley Angus <rangus@student.unimelb.edu.au>
Cc: stable@kernel.org # for v3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
Some of these comments may still need to be reviewed.
This patch only cleans the comment style.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On a set-top-box based on the Broadcom 7405 SoC (MIPS), the Abilis as102 driver
causes a kernel oops while trying to map the URB stream buffers DMA addresses:
CPU 0 Unable to handle kernel paging request at virtual address 007b9900,
epc == 80010cc4, ra == 8039d108
Call Trace:
[<80010cc4>] mips_dma_map_page+0x14/0x108
[<8039d108>] usb_hcd_map_urb_for_dma+0x338/0x4a8
[<8039d540>] usb_hcd_submit_urb+0x2c8/0x8cc
[<e13655d8>] as102_submit_urb_stream+0x64/0xc8 [dvb_as102]
[<e1365680>] as102_usb_start_stream+0x44/0x80 [dvb_as102]
[<e1363628>] as102_dvb_dmx_start_feed+0xb4/0x17c [dvb_as102]
[<803e20f4>] dmx_ts_feed_start_filtering+0x5c/0x134
[<803de454>] dvb_dmxdev_start_feed+0xd4/0x158
[<803dff28>] dvb_dmxdev_filter_start+0x2b8/0x448
[<803e07ac>] dvb_demux_do_ioctl+0x2a0/0x654
[<803ddc8c>] dvb_usercopy+0x124/0x204
[<800d5284>] do_vfs_ioctl+0xa0/0x6c0
[<800d58e8>] sys_ioctl+0x44/0xa8
[<8000ecfc>] stack_done+0x20/0x40
On other boxes based on older SoCs (7401) this doesn't happen, so it looks like
a bug in the kernel specific to MIPS SMP. This issue has been reproduced on
several kernel versions from 2.6.18 to 3.1.0.
Since the base DMA address and the offsets are known, it is possible to map
the DMA addresses of the URB buffers directly in the driver. This workaround
fixes the problem and has been tested on both MIPS and x86 CPUs with success.
By the way, with this fix the driver works perfectly fine on the set-top-box:
both UHF and VHF frequencies are tuned without problems, and zapping is quite
fast. SNR and signal strength reports seems to work fine, too.
The only remaining problem (on both the PC and the set-top-box) is that after
a soft reboot the device is not recognized again by the kernel. It requires
a power cycle (or a manual unplug/replug) to be recognized again. So probably
the device state is not reset properly at shut-down.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If go7007_usb_vendor_request() fails in write_reg_fp()
or in read_reg_fp(), the usb->i2c_lock mutex left locked.
The patch moves mutex_unlock(&usb->i2c_lock) before check
for go7007_usb_vendor_request() returned value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was done to resolve some merge issues with the following files that
had changed in both branches:
drivers/staging/rtl8712/rtl871x_sta_mgt.c
drivers/staging/tidspbridge/rmgr/drv_interface.c
drivers/staging/zcache/zcache-main.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If allocating 'pdata_urb' fails, the function will return -ENOMEM
without freeing the memory allocated, just a few lines above, for
'purb' and will leak that memory when 'purb' goes out of scope.
This patch resolves the leak by freeing the allocated storage with
usb_free_urb() before the return.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If allocating 'pdata_urb' fails, the function will return -ENOMEM
without freeing the memory allocated, just a few lines above, for
'purb' and will leak that memory when 'purb' goes out of scope.
This patch resolves the leak by freeing the allocated storage with
usb_free_urb() before the return.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add MODULE_LICENSE() as per the license in the comment at the top of the
file for this source module to fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (655 commits)
[media] revert patch: HDIC HD29L2 DMB-TH USB2.0 reference design driver
mb86a20s: Add a few more register settings at the init seq
mb86a20s: Group registers into the same line
[media] [PATCH] don't reset the delivery system on DTV_CLEAR
[media] [BUG] it913x-fe fix typo error making SNR levels unstable
[media] cx23885: Query the CX25840 during enum_input for status
[media] cx25840: Add support for g_input_status
[media] rc-videomate-m1f.c Rename to match remote controler name
[media] drivers: media: au0828: Fix dependency for VIDEO_AU0828
[media] convert drivers/media/* to use module_platform_driver()
[media] drivers: video: cx231xx: Fix dependency for VIDEO_CX231XX_DVB
[media] Exynos4 JPEG codec v4l2 driver
[media] doc: v4l: selection: choose pixels as units for selection rectangles
[media] v4l: s5p-tv: mixer: fix setup of VP scaling
[media] v4l: s5p-tv: mixer: add support for selection API
[media] v4l: emulate old crop API using extended crop/compose API
[media] doc: v4l: add documentation for selection API
[media] doc: v4l: add binary images for selection API
[media] v4l: add support for selection api
[media] hd29l2: fix review findings
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The conditional after the kzalloc says that the tested expression should
never be true, but if it were, the allocated data would have to be freed.
This change just moves the allocation below the test, to avoid any
possibility of the problem.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were some curly braces missing so the probe() function always
failed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I changed the function definitions for dt3155_queue_setup() to match the
newer API. The dt3155_start_streaming() function didn't do anything so
I just removed it.
This silences the following gcc warnings:
drivers/staging/media/dt3155v4l/dt3155v4l.c:307:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/staging/media/dt3155v4l/dt3155v4l.c:307:2: warning: (near initialization for ‘q_ops.queue_setup’) [enabled by default]
drivers/staging/media/dt3155v4l/dt3155v4l.c:311:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/staging/media/dt3155v4l/dt3155v4l.c:311:2: warning: (near initialization for ‘q_ops.start_streaming’) [enabled by default]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ops->info.type is handled inside the dvb_frontend
core, only for DVBv3 calls, and according with the
delivery system. So, drivers should not care or use it,
otherwise, it may have issues with DVBv5 calls.
The drivers that were still using it were detected via
this small temporary hack:
--- a/include/linux/dvb/frontend.h
+++ b/include/linux/dvb/frontend.h
@@ -29,13 +29,16 @@
#include <linux/types.h>
typedef enum fe_type {
+#if defined(__DVB_CORE__) || !defined (__KERNEL__)
FE_QPSK,
FE_QAM,
FE_OFDM,
FE_ATSC
+#else
+FE_FOOO
+#endif
} fe_type_t;
-
typedef enum fe_caps {
FE_IS_STUPID = 0,
FE_CAN_INVERSION_AUTO = 0x1,
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using dvb_frontend_parameters struct, that were
designed for a subset of the supported standards, use the DVBv5
cache information.
Also, fill the supported delivery systems at dvb_frontend_ops
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Creates a DVBv5 get_frontend call, renaming the DVBv3 one to
get_frontend_legacy(), while not all frontends are converted.
After the conversion for all drivers, get_frontend_legacy()
will be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Passing DVBv3 parameters to set_frontend is not fun, as the
core doesn't have any way to know if the driver is using the
v3 or v5 parameters. So, rename the callback and add a new
one to allow distinguish between a mixed v3/v5 paramenter call
from a pure v5 call.
After having all frontends to use the new way, the legacy
call can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linux 3.2-rc7
* tag 'v3.2-rc7': (1304 commits)
Linux 3.2-rc7
netfilter: xt_connbytes: handle negation correctly
Btrfs: call d_instantiate after all ops are setup
Btrfs: fix worker lock misuse in find_worker
net: relax rcvbuf limits
rps: fix insufficient bounds checking in store_rps_dev_flow_table_cnt()
net: introduce DST_NOPEER dst flag
mqprio: Avoid panic if no options are provided
bridge: provide a mtu() method for fake_dst_ops
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
sparc64: Fix MSIQ HV call ordering in pci_sun4v_msiq_build_irq().
pata_of_platform: Add missing CONFIG_OF_IRQ dependency.
ipv4: using prefetch requires including prefetch.h
VFS: Fix race between CPU hotplug and lglocks
vfs: __read_cache_page should use gfp argument rather than GFP_KERNEL
USB: Fix usb/isp1760 build on sparc
net: Add a flow_cache_flush_deferred function
...
Conflicts:
drivers/media/common/tuners/tda18218.c
drivers/media/video/omap3isp/ispccdc.c
drivers/staging/media/as102/as102_drv.h
commit a846d8fce9e8be30046be3c512982bd0345e7015
The 2250 board uses bulk endpoint for interrupt handling,
and should use a bulk urb instead of an int urb.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the Sky Italia Digital Key, an USB dongle offered
by Sky Italia to its customers for use with their satellite set-top-boxes.
This is the "green led" model based on the Abilis as102 chip, while the
so called "blue led" model is based on the Avermedia A867 design.
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com>
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop usb_class_driver and collaterals as it is not used
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add easycap prefix to global function to reduce
possibility of name collision.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. kill_video_usb can be used in all places where video urbs are killed
and reduce code repetition
2. remove unnecessary check for easycap == NULL in the function
as it is always checked by the calling function
3. rename the function to easycap_video_kill_urb to reduce
possibility of name conflict
4. implement also easycap_audio_kill_urb
5. simplify freeing urbs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
peasycap was allocated using kzalloc so drop all
to zero initializations
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
change statements of types
if (err)
return err
else
do something
and
if (ok)
do something
else
return err
into
if (err)
return err
do something
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. saa and stk initialization tables are less then
256 entries
2. stk table can fit into u16 and saa into u8
size before
text data bss dec hex filename
105687 1072 1134800 1241559 12f1d7 easycap.ko
size after
text data bss dec hex filename
97919 1072 1134800 1233791 12d37f easycap.ko
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
