There is no technical reason that the kgdb core requires frame
pointers. It is up to the end user of KGDB to decide if they need
them or not.
[ anemo@mba.ocn.ne.jp: removed frame pointers on mips ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
While the rfkill class does work with just get_state(), it doesn't work
well on devices that are subject to external events that cause rfkill state
changes.
Document that rfkill_force_state() is required in those cases.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: turn Waker into a thread, not a process
lguest: Enlarge virtio rings
lguest: Use GSO/IFF_VNET_HDR extensions on tun/tap
lguest: Remove 'network: no dma buffer!' warning
lguest: Adaptive timeout
lguest: Tell Guest net not to notify us on every packet xmit
lguest: net block unneeded receive queue update notifications
lguest: wrap last_avail accesses.
lguest: use cpu capability accessors
lguest: virtio-rng support
lguest: Support assigning a MAC address
lguest: Don't leak /dev/zero fd
lguest: fix verbose printing of device features.
lguest: fix switcher_page leak on unload
lguest: Guest int3 fix
lguest: set max_pfn_mapped, growl loudly at Yinghai Lu
lguest uses a Waker process to break it out of the kernel (ie.
actually running the guest) when file descriptor needs attention.
Changing this from a process to a thread somewhat simplifies things:
it can directly access the fd_set of things to watch. More
importantly, it means that the Waker can see Guest memory correctly,
so /dev/vring file descriptors will work as anticipated (the
alternative is to actually mmap MAP_SHARED, but you can't do that with
/dev/zero).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since the correct timeout value varies, use a heuristic which adjusts
the timeout depending on how many packets we've seen. This gives
slightly worse results, but doesn't need tweaking when GSO is
introduced.
500 usec 19.1887 xmit 561141 recv 1 timeout 559657
Dynamic (278) 20.1974 xmit 214510 recv 5 timeout 214491 usec 278
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_ring has the ability to suppress notifications. This prevents
a guest exit for every packet, but we need to set a timer on packet
receipt to re-check if there were any remaining packets.
Here are the times for 1G TCP Guest->Host with different timeout
settings (it matters because the TCP window doesn't grow big enough to
fill the entire buffer):
Timeout value Seconds Xmit/Recv/Timeout
None (before) 25.3784 xmit 7750233 recv 1
2500 usec 62.5119 xmit 207020 recv 2 timeout 207020
1000 usec 34.5379 xmit 207003 recv 2 timeout 207003
750 usec 29.2305 xmit 207002 recv 1 timeout 207002
500 usec 19.1887 xmit 561141 recv 1 timeout 559657
250 usec 20.0465 xmit 214128 recv 2 timeout 214110
100 usec 19.2583 xmit 561621 recv 1 timeout 560153
(Note that these values are sensitive to the GSO patches which come
later, and probably other traffic-related variables, so take with a
large grain of salt).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To simplify the transition to when we publish indices in the ring
(and make shuffling my patch queue easier), wrap them in a lg_last_avail()
macro.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a simple patch to add support for the virtio "hardware random
generator" to lguest. It gets about 1.2 MB/sec reading from /dev/hwrng
in the guest.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If you've got a nice DHCP configuration which maps MAC
addresses to specific IP addresses, then you're going to
want to start your guest with one of those MAC addresses.
Also, in Fedora, we have persistent network interface naming
based on the MAC address, so with randomly assigned
addresses you're soon going to hit eth13. Who knows what
will happen then!
Allow assigning a MAC address to the network interface with
e.g.
--tunnet=bridge:eth0:00:FF:95:6B:DA:3D
or:
--tunnet=192.168.121.1:00:FF:95:6B:DA:3D
which is pretty unintelligable, but ...
(includes Rusty's minor rework)
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This file contains 8 yr. old board specific information that was for
the now gone ppc implementation, and it pre-dates widespread u-boot
support. Any of the technical details of the board memory map would be
more appropriately captured in a dts if I revive it as powerpc anyway.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add git pull command info and diffstat summary info so that we don't
have to search email archives for it repeatedly.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the get_mctrl/set_mctrl stubs with modem control line
read/write access through the GPIO lib.
Available modem control lines are described in the device tree using GPIO
bindings. The driver expect a GPIO pin for each of the CTS, RTS, DCD, DSR,
DTR and RI signals. Unused control lines can be left out.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a document describing how i2c clients on Linux 2.6 can be
moved from the old to the new driver model.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
- New supported IDs for analog models
(Based on Markus Rechberger <mrechberger@gmail.com> version of em28xx driver)
- Validation field for new em28xx boards.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
[mchehab@infradead.org: Need to fix some merge conflicts]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (25 commits)
setlocalversion: do not describe if there is nothing to describe
kconfig: fix typos: "Suport" -> "Support"
kconfig: make defconfig is no longer chatty
kconfig: make oldconfig is now less chatty
kconfig: speed up all*config + randconfig
kconfig: set all new symbols automatically
kconfig: add diffconfig utility
kbuild: remove Module.markers during mrproper
kbuild: sparse needs CF not CHECKFLAGS
kernel-doc: handle/strip __init
vmlinux.lds: move __attribute__((__cold__)) functions back into final .text section
init: fix URL of "The GNU Accounting Utilities"
kbuild: add arch/$ARCH/include to search path
kbuild: asm symlink support for arch/$ARCH/include
kbuild: support arch/$ARCH/include for tags, cscope
kbuild: prepare headers_* for arch/$ARCH/include
kbuild: install all headers when arch is changed
kbuild: make clean removes *.o.* as well
kbuild: optimize headers_* targets
kbuild: only one call for include/ in make headers_*
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Allow to force model to intel-mac-v3 in snd_hda_intel (sigmatel).
ALSA: cs4232: fix crash during chip PNP detection
ALSA: hda - Add automatic model setting for the Acer Aspire 5920G laptop
ALSA: make snd_ac97_add_vmaster() static
ALSA: sound/pci/azt3328.h: no variables for enums
ALSA: soc - wm9712 mono mixer
ALSA: hda - Add support of ASUS Eeepc P90*
ALSA: opti9xx: no isapnp param for !CONFIG_PNP
ALSA: opti93x - Fix NULL dereference
ALSA: hda - Added support for Asus V1Sn
ALSA: ASoC: Factor PGA DAPM handling into main
ALSA: ASoC: Refactor DAPM event handler
ALSA: ALSA: ens1370: communicate PCI device to AC97
ALSA: ens1370: SRC stands for Sample Rate Converter
ALSA: hda - Align BDL position adjustment parameter
ALSA: Au1xpsc: psc not disabled when TX is idle
ALSA: add TriTech 28023 AC97 codec ID and Wolfson 9701 name.
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, even if you pass model=intel-mac-v3 as a module parameter to
snd_hda_intel, the function patch_stac922x (patch_sigmatel.c) will still
try to auto-detect the model type. This is a problem on my MacBook Pro 1st
generation, which needs intel-mac-v3, but sometimes incorrectly reports
0x00000100 as subsystem id, which causes the switch in patch_stac922x to
select intel-mac-v4.
To fix this, I added a new model called intel-mac-auto, so in case no
module parameter is passed, and an Intel Mac board is detected, the
model will be automatically detected, while no detection will be done
if the model is forced to intel-mac-v3.
This problem has been around for quite a while, and I used to fix it
by moving the case statement for 0x00000100 in patch_stac922x so that
intel-mac-v3 is chosen.
Another way to fix the problem would be to check if a module parameter
was set directly in patch_stac922x, using something like this:
if (spec->board_config == STAC_INTEL_MAC_V3 &&
!codec->bus->modelname) {
But I think it is less elegant (if you prefer that way, I can prepare a
patch).
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
mISDN is a new modular ISDN driver, in the long term it should replace
the old I4L driver architecture for passiv ISDN cards.
Signed-off-by: Karsten Keil <kkeil@suse.de>
These patches add the Optimized MPEG Filesystem, a proprietary filesystem used
by the embedded devices Rio Karma and ReplayTV, which are no longer
manufactured. This filesystem module enables people to access files on these
devices.
This patch:
OMFS is a proprietary filesystem created for the ReplayTV and also used by the
Rio Karma. It uses hash tables with unordered, unbounded lists in each bucket
for directories, extents for data blocks, 64-bit addressing for blocks, with
up to 8K blocks (only 2K of a given block is ever used for metadata, so the FS
still works with 4K pages).
Document the filesystem usage and structures.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allows one to create and use a channel with no associated files. Files
can be initialized later. This is useful in scenarios such as logging in
early code, before VFS is up. Therefore, such channels can be created and
used as soon as kmem_cache_init() completed.
This is needed by kmemtrace to do tracing in early kernel code.
[kosaki.motohiro@jp.fujitsu.com: build fix]
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
em28xx-cards.c
em28xx-dvb.c
em28xx.h
- Add support for the ATI TV Wonder HD 600, based on a 94 email exchange and
USB traces provided by Ronnie Bailey
Thanks to Ronnie Bailey <purevw@wtxs.net> for testing the changes
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Documentation/sparse.txt tells to use:
make C=2 CHECKFLAGS="-D__CHECK_ENDIAN__"
However, this still doesn't enable endian checks. The correct syntax is:
make C=2 CF="-D__CHECK_ENDIAN__"
This documentation bug was introduced by the following commit:
commit 1c7bafe720
Author: Robert P. J. Day <rpjday@mindspring.com>
Date: Wed Sep 13 07:57:50 2006 -0400
kbuild: clarify "make C=" build option
Clarify the use of "make C=" in the top-level Makefile, and fix a
typo in the Documentation file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This `typo' was not a typo, as `CF' had been introduced much earlier, by:
commit 7b49bb9aff
Author: viro@ZenIV.linux.org.uk <viro@ZenIV.linux.org.uk>
Date: Fri Sep 9 21:14:35 2005 +0100
[PATCH] kbuild: CF=<arguments> passes arguments to sparse
Allows to add to sparse arguments without mutilating makefiles - just
pass CF=<arguments> and they will be added to CHECKFLAGS.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
/sys/devices/system/edac/mc has a few files which are duplicated in
/sys/module/edac_core/parameters. Now that all the functionality is
duplicated between these two locations, we remove the former kobject
attributes and update the documentation.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update document and make getdelays.c show delay accounting for memory reclaim.
For making a distinction between "swapping in pages" and "memory reclaim"
in getdelays.c, MEM is changed to SWAP.
Signed-off-by: Keika Kobayashi <kobayashi.kk@ncos.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add members for memory reclaim delay to taskstats, and accumulate them in
__delayacct_add_tsk() .
Signed-off-by: Keika Kobayashi <kobayashi.kk@ncos.nec.co.jp>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems to me that it was a mistake marking this function as deprecated
and scheduling it for removal, rather than resolutely removing it after
the last caller's death.
Anyway - better late, then never.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
