2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-22 20:23:57 +08:00
Commit Graph

7972 Commits

Author SHA1 Message Date
andrew.vasquez@qlogic.com
c9d02acf39 [SCSI] qla2xxx: Correct issue where portstate does not transition during loop-resync.
If the Get Port Database call fails during local-loop
update, then schedule the DPC routine to perform a rescan as
the firmware would have updated the Get ID List port-entries
of their new state.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:31 -06:00
andrew.vasquez@qlogic.com
210d53507e [SCSI] qla2xxx: Update firmware-dump procedure for ISP24xx.
Small changes to register retrieval and order as per latest
firmware specification.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:30 -06:00
andrew.vasquez@qlogic.com
e978010ceb [SCSI] qla2xxx: Re-enable flash-part write protection on ISP24xx boards.
Driver would not correctly re-enable the write-protection
bits of the flash part after updates.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:29 -06:00
andrew.vasquez@qlogic.com
5998983113 [SCSI] qla2xxx: Correct excessive delay during LOAD-RISC-RAM mailbox command.
Problem report (against 2.4.x driver) from Jeff Layton
<jlayton@redhat.com>:

An OEM noticed that the U6 qla2200 driver would hang for
around 2 minutes at boot time and then proceed normally. I
found that the delay was occurring when loading the new
firmware into the card, and was due to a
schedule_timeout(10) added to the bottom of the polling
loop.

Some testing showed that the load ram operation on the card
was very quick (on the order of a couple of jiffies), but
the sleep in the polling loop was making each operation take
around 25-30.

The attached patch corrects this by making it skip sleeping
during the load ram operation, since I believe we only do
that when the module is plugged in. It also skips sleeping
if the mbox_int flag got set during the current loop.

This corrected the hang on my test setup, and OEM also
confirmed that it corrected the problem for them.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:28 -06:00
andrew.vasquez@qlogic.com
03ab2eabed [SCSI] qla2xxx: Use msleep() as delay during ISP polling.
Mailbox commands are polled for completion during ISP
initialization.  During potentially 'long' mailbox commands
(i.e. fabric login), we really don't want a busy-wait delay
to potentially trigger a (benign) soft-lockup BUG().

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:27 -06:00
andrew.vasquez@qlogic.com
e038a1be22 [SCSI] qla2xxx: Drop noisy 'UNDERRUN' status message.
There's no point in displaying the message during a valid
underrun case.  Limit the message to potentially problematic
cases.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:26 -06:00
andrew.vasquez@qlogic.com
9403688e9b [SCSI] qla2xxx: Correct FC4 feature assignment during RFF_ID.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:24 -06:00
andrew.vasquez@qlogic.com
dad9c8c15d [SCSI] qla2xxx: Reference proper node/port names in fc_host class.
The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:23 -06:00
Mike Christie
a1e80c20e1 [SCSI] iscsi: use pageslab
From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com:

We cannot handle filesystems like XFS becuase of the pages they
are sending us. We had thought page_count could be used to
work around this, but the correct test is for PageSlab.

The proper solution is to figure out what type of pages
filesystems can use so we do not have to add tests like
this or handle it in the block layer for all network block drivers
but the issue still has not been resolved on fs-devel
so we are sending this patch as a temporary fix.

This is last patch just in case it is Nakd with the explanation
that we need to push the correct fix through fs-devel, mm
or the block layer. The rest of the patchset can live without
the patch, but the driver will not work with filesystems like
XFS.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:22 -06:00
Mike Christie
55e3299d9e [SCSI] iscsi: fix 4k stack iscsi setups
When we run the xmit code from queuecomand the stack trace
gets too deep. The patch runs the xmit code from the scsi_host
work queue. This fixes 4k stack and xfs support and should
fix the st and sg stack usage bugs.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:21 -06:00
Mike Christie
7b8631b53b [SCSI] iscsi: seperate iscsi interface from setup functions
This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.

The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.

This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:20 -06:00
Mike Christie
7cae5159dd [SCSI] iscsi: add high mem support
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>:

We cannot use page_address becuase some pages could be highmem.
Instead, we can use sock_no_sendpage which does kmap for us.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:18 -06:00
FUJITA Tomonori
56851698c2 [SCSI] iscsi: data digest page cache usage fix
Users can write to a page while we are sending it and making
digest calculations. This ends up causing us to retry the command
when a digest error is later reported. By using sock_no_sendpage
when data digests are calculated we can avoid a lot of (not all but it
helps) the retries becuase sock_no_sendpage is not zero copy.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:17 -06:00
zhenyu.z.wang@intel.com
3e97c7e6cd [SCSI] iscsi: host locking fix
We should be taking the host_lock instead of the conn lock when
checking host_busy.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:16 -06:00
zhenyu.z.wang@intel.com
bf310b8f58 [SCSI] iscsi: data under/over flow fix
We need to check the ISCSI_FLAG_DATA_* flags.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:15 -06:00
FUJITA Tomonori
42f72aa9e5 [SCSI] iscsi: whitespace cleanup
Remove extra whitespaces.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:14 -06:00
Jes Sorensen
a12e25bd59 [SCSI] sem2mutex 3w-[x9]xxx
Convert a the 3w-9xxx.c and 3w-xxxx.c drivers to use mutexes instead
of semaphores. Untested, but compiles and looks obviously correct.

Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:12 -06:00
James Bottomley
3759b78849 [SCSI] mptfc: need to select transport attrs
Now that mptfc actually uses the transport class, it can't be built
without it.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:11 -06:00
Moore, Eric
569b11dcfa [SCSI] fusion - fix pci express bug
The fix is to write  'MPI_HIM_DIM' to the Host Interrupt Mask
register, when enabling interrupts.  Instead of the
tilde of MPI_HIM_RIM.

Apparently writing '1's to some of the reserved bits was causing
all the bits to go to `1`, which effectly disabled all interrupts.

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:10 -06:00
Moore, Eric
e6bc863cf2 [SCSI] scsi_transport_sas: mapping the rphy channel equal to the port identifier
We will be mapping the RAID volumes in mptsas to a reserved
channel that
is one larger than the anticapated number of ports on the direct
attached host
adapter.

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:09 -06:00
Moore, Eric
4b915a7366 [SCSI] fusion - mpi header udpate
This updates mpi headers in fusion drivers to version 1.5.12.

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:08 -06:00
Moore, Eric
816aa907b9 [SCSI] fusion - adding raid support in mptsas
The SAS RAID volumes are reported beyond the expected number of phys.

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:06 -06:00
Christoph Hellwig
e02f3f5922 [SCSI] remove target parent limitiation
When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.

When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.

So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning.  As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.

For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:05 -06:00
Moore, Eric
6d5b0c315e [SCSI] fusion - adding support for FC949ES
Add software recognition for the new LSI Logic Fibre Channel controller.

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:04 -06:00
Michael Reed
05e8ec17f4 [SCSI] mptfusion - fc transport attributes
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:02 -06:00
Jes Sorensen
d158d26167 [SCSI] sem2mutex: scsi_transport_spi.c
Convert the SCSI transport class code to use a mutex rather than a
semaphore.

Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:01 -06:00
James Bottomley
f20139bee4 [SCSI] fix up message/i2o/pci.c
There was a use before initialisation of c->name

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:59 -06:00
Christoph Hellwig
1ca00bb791 [SCSI] fusion: kzalloc / kcalloc conversion
Convert kmalloc + memset to kzalloc or kcalloc in fusion.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:58 -06:00
Christoph Hellwig
eeb846cefd [SCSI] fusion: convert semaphores to mutexes
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:57 -06:00
Christoph Hellwig
9a28f49adb [SCSI] mptsas: support basic hotplug
Adds hotplug support for SAS end devices.  Unfortunately the fusion
firmware doesn't generate similar events for expanders addition/removal
so we can't support them yet.  Eric has an idea about a clever scheme to
find out about expander changes so that'll be added later on.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:56 -06:00
Salyzyn, Mark
9638d89a75 [SCSI] I2O: move pci_request_regions() just behind pci_enable_device()
The problem in dpt_i2o could be the pci config space accesses it
triggers as it loads, dangerous to do if there is any I/O activity going
on in the other driver (probable if a boot driver I guess).

I approve this patch to dpt_i2o.c, and am applying it to the Adaptec
branch of the driver.

Thanks for the investigation Ryoji.

---

In linux 2.6.15, data transfer does hang when both dpt_i2o
and i2o_block drivers are loaded.
It seems that location of pci_request_regions() are wrong.
I moved it just behind pci_enable_device() like other drivers,
and it becomes fine.

Signed-off-by: Ryoji Kamei <kamei@miraclelinux.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:54 -06:00
Jack Hammer
560c26c834 [SCSI] ips: Mode Sense (Caching Page ) fix
To avoid the "sda: got wrong page" message, the ServeRAID driver
should be setting flags indicating that the Mode Sense commands are
not supported.

Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:53 -06:00
Andreas Herrmann
ad757cdfd2 [SCSI] zfcp: transport class adaptations II
Replaced zfcp adapter attributes with fc_host attributes:
fc_topology by port_type, physical_wwpn by permanent_port_name.
Make use of fc_host attribute supported_speeds.
Removed zfcp adapter attribute physical_s_id.

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:52 -06:00
Andreas Herrmann
f6cd94b126 [SCSI] zfcp: transport class adaptations
Added host stats, removed superfluous get_starget_ functions,
removed some attributes from zfcp specific sysfs tree (e.g.
scsi_host_no, scsi_lun, wwnn and d_id).
Host stats are given for the physical adapter port not for the
virtual adapter. Reset stats is implemented in the device driver.

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:50 -06:00
Maxim Shchetynin
9eb69aff79 [SCSI] zfcp: handle unsolicited status notification lost
Handle unsolicited adapter status that informs about loss of
previous unsolicited status notification(s).

Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:49 -06:00
Andreas Herrmann
6b7281d0a0 [SCSI] fc transport: add permanent_port_name fc_host attribute
Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.

For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:48 -06:00
Christoph Hellwig
a09c631121 [SCSI] sr: split sr_audio_ioctl into specific helpers
split each ioctl handled in sr_audio_ioctl into a function of it's own.
This cleans the code up nicely, and allows various places in sr_ioctl
to call these helpers directly instead of going through the multiplexer.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:46 -06:00
Christoph Hellwig
776b23a036 [SCSI] always handle REQ_BLOCK_PC requests in common code
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code.  There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.

Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:45 -06:00
Christoph Hellwig
d405423992 [SCSI] sas: fix removal of devices behind expanders
We need to iterate over all children when removing and expander, else
stale objects will be around after host removal.  This fixes the oops
Eric Moore saw when removing and reloading mptsas.

Also don't try the scsi_remove_target call unless operating on an end
device.  The current unconditional call is harmless but confusing.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:54:44 -06:00
Michael Hanselmann
eab9edd27f Input: HID - add support for fn key on Apple PowerBooks
This patch implements support for the fn key on Apple PowerBooks using
USB based keyboards and makes them behave like their ADB counterparts.

Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Rene Nussbaumer <linux-kernel@killerfox.forkbomb.ch>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 10:08:06 -05:00
Dmitry Torokhov
1e27ffd4d7 Input: wacom - fix compile on PowerPC
Rename G4 (new Graphire4) to WACOM_G4 to avoid clashes on PowerPC

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 00:28:04 -05:00
Dmitry Torokhov
5fce9d7bc5 Input: HID - add more simulation usages
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 00:27:51 -05:00
Dmitry Torokhov
f0d5c6f419 Input: psmouse - attempt to re-synchronize mouse every 5 seconds
This should help driver to deal vith KVMs that reset mice when
switching between boxes.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 00:27:37 -05:00
Dmitry Torokhov
b65d0d1bac Input: HID - fix an oops in PID initialization code
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 00:26:15 -05:00
Vojtech Pavlik
940824b0ac Input: HID - add support for Cherry Cymotion keyboard
The Cherry Cymotion is a special Linux keyboard made by Cherry, with
only one little problem: it doesn't work with Linux. This patch
(originally by hexten.net, cleaned up by me) makes it work including
all the special keys.

Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 00:25:39 -05:00
Linus Torvalds
87530db5ec Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge 2006-01-13 21:24:55 -08:00
Vojtech Pavlik
3dd01a8311 Input: i8042 - add Sony Vaio FSC-115b to MUX blacklist
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2006-01-14 00:24:06 -05:00
David Woodhouse
36874579db [PATCH] powerpc: macio-adb build fix
This makes macio-adb.c build again. Entirely untested.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-14 13:19:18 +11:00
David Brownell
2e10c84b9c [PATCH] SPI: add spi_butterfly driver
This adds a bitbanging parport based adaptor cable for AVR Butterfly, giving
SPI links to its DataFlash chip and (eventually) firmware running in the card.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:56 -08:00
Andrew Morton
5d870c8e21 [PATCH] spi: remove fastcall crap
gcc4 generates warnings when a non-FASTCALL function pointer is assigned to a
FASTCALL one.  Perhaps it has taste.

Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:56 -08:00
David Brownell
7111763d39 [PATCH] spi: misc fixes
This collects some small SPI patches that seem to be missing from the MM tree:

  - spi_butterfly kbuild hooks got dropped somehow; this restores them
  - quick fix for a (theoretical?) m25p80_write() oops noted by Andrew
  - quick fix for a potential config-specific oops for mtd_dataflash()
  - minor doc tweaks

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:56 -08:00
Vitaly Wool
8275c642cc [PATCH] spi: use linked lists rather than an array
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.

From: David Brownell <dbrownell@users.sourceforge.net>

  Updates including doc, bugfixes to the list code, add
  spi_message_add_tail().  Plus, initialize things _before_ grabbing the
  locks in some cases (in case it grows more expensive).  This also merges
  some bitbang updates of mine that didn't yet make it into the mm tree.

Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:56 -08:00
Mike Lavender
2f9f762879 [PATCH] spi: M25 series SPI flash
This was originally a driver for the ST M25P80 SPI flash.  It's been
updated slightly to handle other M25P series chips.

For many of these chips, the specific type could be probed, but for now
this just requires static setup with flash_platform_data that lists the
chip type (size, format) and any default partitioning to use.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mike Lavender <mike@steroidmicros.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:55 -08:00
David Brownell
9904f22a72 [PATCH] spi: add spi_bitbang driver
This adds a bitbanging spi master, hooking up to board/adapter-specific glue
code which knows how to set and read the signals (gpios etc).

This code kicks in after the glue code creates a platform_device with the
right platform_data.  That data includes I/O loops, which will usually
come from expanding an inline function (provided in the header).  One goal
is that the I/O loops should be easily optimized down to a few GPIO register
accesses, in common cases, for speed and minimized overhead.

This understands all the currently defined protocol tweaking options in the
SPI framework, and might eventually serve as as reference implementation.

  - different word sizes (1..32 bits)
  - differing clock rates
  - SPI modes differing by CPOL (affecting chip select and I/O loops)
  - SPI modes differing by CPHA (affecting I/O loops)
  - delays (usecs) after transfers
  - temporarily deselecting chips in mid-transfer

A lot of hardware could work with this framework, though common types of
controller can't reach peak performance without switching to a driver
structure that supports pipelining of transfers (e.g.  DMA queues) and maybe
controllers (e.g.  IRQ driven).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:55 -08:00
David Brownell
2e5a7bd978 [PATCH] spi: ads7836 uses spi_driver
This updates the ads7864 driver to use the new "spi_driver" struct, and
includes some minor unrelated cleanup.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:55 -08:00
David Brownell
0c868461fc [PATCH] SPI core tweaks, bugfix
This includes various updates to the SPI core:

  - Fixes a driver model refcount bug in spi_unregister_master() paths.

  - The spi_master structures now have wrappers which help keep drivers
    from needing class-level get/put for device data or for refcounts.

  - Check for a few setup errors that would cause oopsing later.

  - Docs say more about memory management.  Highlights the use of DMA-safe
    i/o buffers, and zero-initializing spi_message and such metadata.

  - Provide a simple alloc/free for spi_message and its spi_transfer;
    this is only one of the possible memory management policies.

Nothing to break code that already works.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:55 -08:00
David Brownell
b885244eb2 [PATCH] spi: add spi_driver to SPI framework
This is a refresh of the "Simple SPI Framework" found in 2.6.15-rc3-mm1
which makes the following changes:

  * There's now a "struct spi_driver".  This increase the footprint
    of the core a bit, since it now includes code to do what the driver
    core was previously handling directly.  Documentation and comments
    were updated to match.

  * spi_alloc_master() now does class_device_initialize(), so it can
    at least be refcounted before spi_register_master().  To match,
    spi_register_master() switched over to class_device_add().

  * States explicitly that after transfer errors, spi_devices will be
    deselected.  We want fault recovery procedures to work the same
    for all controller drivers.

  * Minor tweaks:  controller_data no longer points to readonly data;
    prevent some potential cast-from-null bugs with container_of calls;
    clarifies some existing kerneldoc,

And a few small cleanups.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:54 -08:00
David Brownell
1d6432fe10 [PATCH] spi: mtd dataflash driver
This is a conversion of the AT91rm9200 DataFlash MTD driver to use the
lightweight SPI framework, and no longer be AT91-specific.  It compiles
down to less than 3KBytes on ARM.

The driver allows board-specific init code to provide platform_data with
the relevant MTD partitioning information, and hotplugs.

This version has been lightly tested.  Its parent at91_dataflash driver has
been pretty well banged on, although kernel.org JFFS2 dataflash support was
acting broken the last time I tried it.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:54 -08:00
David Brownell
ffa458c1bd [PATCH] spi: ads7846 driver
This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers.  Key differences from those two:

  - Uses the new SPI framework (minimalist version)
  - <linux/spi/ads7846.h> abstracts board-specific touchscreen info
  - Sysfs attributes for the temperature and voltage sensors
  - Uses fewer ARM-specific IRQ primitives

The temperature and voltage sensors show up in sysfs like this:

  $ pwd
  /sys/devices/platform/omap-uwire/spi2.0
  $ ls
  bus@          input:event0@ power/        temp1         vbatt
  driver@       modalias      temp0         vaux
  $ cat modalias
  ads7846
  $ cat temp0
  991
  $ cat temp1
  1177
  $

So far only basic testing has been done.  There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.

One portability note may be of special interest.  It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response".  Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention.  So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.

Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:54 -08:00
David Brownell
8ae12a0d85 [PATCH] spi: simple SPI framework
This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).

  - It's still less than 2KB of ".text" (ARM).  If there's got to be a
    mid-layer for something so simple, that's the right size budget.  :)

  - The guts use board-specific SPI device tables to build the driver
    model tree.  (Hardware probing is rarely an option.)

  - This version of Kconfig includes no drivers.  At this writing there
    are two known master controller drivers (PXA/SSP, OMAP MicroWire)
    and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
    mentions of other drivers in development.

  - No userspace API.  There are several implementations to compare.
    Implement them like any other driver, and bind them with sysfs.

The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:

  - One bugfix (removes a FIXME), with the visible effect of making device
    names be "spiB.C" where B is the bus number and C is the chipselect.

  - The "caller provides DMA mappings" mechanism now has kerneldoc, for
    DMA drivers that want to be fancy.

  - Hey, the framework init can be subsys_init.  Even though board init
    logic fires earlier, at arch_init ... since the framework init is
    for driver support, and the board init support uses static init.

  - Various additional spec/doc clarifications based on discussions
    with other folk.  It adds a brief "thank you" at the end, for folk
    who've helped nudge this framework into existence.

As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.

From: Mark Underwood <basicmark@yahoo.com>

  Update the SPI framework to remove a potential priority inversion case by
  reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 16:29:54 -08:00
Linus Torvalds
fb7ffeb11b Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband 2006-01-13 15:29:07 -08:00
Ingo Molnar
95ed644fd1 IB: convert from semaphores to mutexes
semaphore to mutex conversion by Ingo and Arjan's script.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Sanity-checked on real IB hardware ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-13 14:51:39 -08:00
Dmitry Torokhov
7493a314cb [SERIAL] serial8250: convert to the new platform device interface
Do not use platform_device_register_simple() as it is going away.
Also set up driver's owner to create link driver->module in sysfs.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13 22:06:43 +00:00
Adrian Bunk
d600b97cf6 [SERIAL] fix SERIAL_M32R_PLDSIO dependencies
This patch fixes a typo in the dependencies reported by
Jean-Luc Leger <reiga@dspnet.fr.eu.org>.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13 21:57:22 +00:00
Andrew Morton
51828abc17 [MMC] mmc_blk_probe() warning fix
drivers/mmc/mmc_block.c: In function `mmc_blk_probe':
drivers/mmc/mmc_block.c:467: warning: long unsigned int format, different type arg (arg 5)

We don't know what size sector_t is - cast it.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13 21:44:18 +00:00
Ingo Molnar
e2862f6a83 [SERIAL] convert uart_state.sem to uart_state.mutex
semaphore to mutex conversion.

the conversion was generated via scripts, and the result was validated
automatically via a script as well.

build and boot tested.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13 21:37:07 +00:00
Matt Reimer
3261e362f6 [ARM] 3258/1: IMX serial: fix parity
Patch from Matt Reimer

IMX serial parity generation doesn't work because of a simple logic error. This patch fixes it and now Bluetooth works on R1000.

Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13 20:51:44 +00:00
Michael Richardson
9c08a938ce [PATCH] device_shutdown can loop if the driver frees itself
This patch changes device_shutdown() to use the newly introduced safe
reverse list traversal.  We experienced loops on system reboot if we had
removed and re-inserted our device from the device list.

We noticed this problem on PPC405. Our PCI IDE device comes and goes a lot.

Our hypothesis was that there was a loop caused by the driver->shutdown
freeing memory.  It is possible that we do something wrong as well, but
being unable to reboot is kind of nasty.

Signed-off-by: Michael Richardson <mcr@marajade.sandelman.ca>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:12 -08:00
Jean Delvare
2d7b5a70e0 [PATCH] platform-device-del typo fix
Please fold this typo fix into platform-device-del.patch, as was
discussed earlier on LKML:
  http://lkml.org/lkml/2005/12/10/76

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:11 -08:00
Cornelia Huck
8bbace7e68 [PATCH] Add {css,ccw}_bus_type probe, remove, shutdown methods.
The following patch converts css_bus_type and ccw_bus_type to use
the new bus_type methods.

Signed-off-by: Cornelia Huck <huckc@de.ibm.com>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:11 -08:00
Russell King
348290a4ae [PATCH] Add bttv sub bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:11 -08:00
Russell King
d78967fb03 [PATCH] Remove usb gadget generic driver methods
USB gadget drivers make no use of these, remove the pointless
comments.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:11 -08:00
Russell King
4031bbe4bb [PATCH] Add ide_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:10 -08:00
Russell King
bbbe3a41f7 [PATCH] Add Pseudo LLD bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:10 -08:00
Russell King
fc3d3ddd3e [PATCH] Add rio_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:10 -08:00
Russell King
b6a01e9bda [PATCH] Add zorro_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:10 -08:00
Russell King
ac33bc3d54 [PATCH] Add usb_serial_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:09 -08:00
Russell King
ff2dae7977 [PATCH] Add superhyway_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:09 -08:00
Russell King
f9ccf4569a [PATCH] Add ccwgroup_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:09 -08:00
Russell King
4681fc3208 [PATCH] Add pnp_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:09 -08:00
Russell King
1d0baa3a1c [PATCH] Add pcmcia_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:08 -08:00
Russell King
4d0b653cdf [PATCH] Add mmc_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:08 -08:00
Russell King
413b486e18 [PATCH] Add MCP bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:08 -08:00
Russell King
4866b124a1 [PATCH] Add macio_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:08 -08:00
Russell King
30226f8199 [PATCH] Add serio bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:07 -08:00
Russell King
29a4a20e9f [PATCH] Add gameport bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:07 -08:00
Russell King
b864c7d5d1 [PATCH] Add i2c_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:07 -08:00
Russell King
5b34bf8877 [PATCH] Add dio_bus_type probe and remove methods
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:07 -08:00
Russell King
b15d686a2b [PATCH] Add pci_bus_type probe and remove methods
Move the PCI bus device probe/remove methods to the bus_type
structure.  We leave the shutdown method alone since there
are compatibility issues with that.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:04 -08:00
Russell King
594c8281f9 [PATCH] Add bus_type probe, remove, shutdown methods.
Add bus_type probe, remove and shutdown methods to replace the
corresponding methods in struct device_driver.  This matches
the way we handle the suspend/resume methods.

Since the bus methods override the device_driver methods, warn
if a device driver is registered whose methods will not be
called.

The long-term idea is to remove the device_driver methods entirely.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:04 -08:00
Kay Sievers
bd37e5a951 [PATCH] INPUT: add MODALIAS to the event environment
input: add MODALIAS to the event environment

Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-13 11:26:04 -08:00
Michael S. Tsirkin
9eacee2ac6 IB/mthca: Initialize grh_present before using it
build_mlx_header() was using sqp->ud_header.grh_present before it was
initialized by mthca_read_ah().  Furthermore, header->grh_present is
set by ib_ud_header_init, so there's no need to set it again in
mthca_read_ah().

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-12 15:55:41 -08:00
Michael S. Tsirkin
c063a06835 IB/mthca: Cosmetic: use the ALIGN macro
Use the ALIGN macro to simplify some rounding code.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-12 15:43:58 -08:00
Linus Torvalds
43ecb9a33b Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 2006-01-12 15:43:39 -08:00
Jack Morgenstein
17e2e81951 IB/mthca: Fix memory leaks in error handling
Fix memory leaks in mthca_create_qp() and mthca_create_srq()
error handling.

Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-12 15:35:15 -08:00
Ishai Rabinovitz
59f174faff IB/mthca: Fix memory leak of multicast group structures
Convert "/ (1 << lg)" to ">> lg" for a slight code size reduction.

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-24 (-24)
function                                     old     new   delta
mthca_map_cmd                                613     589     -24

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-12 15:24:51 -08:00
Eli Cohen
988bd50300 IPoIB: Fix memory leak of multicast group structures
The current handling of multicast groups in IPoIB ends up never
freeing send-only multicast groups.  It turns out the logic was much
more complicated than it needed to be; we can fix this bug and
completely kill ipoib_mcast_dev_down() at the same time.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-12 14:32:20 -08:00
Linus Torvalds
58cba4650a Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6 2006-01-12 14:00:47 -08:00
Linus Torvalds
37ef4399a6 Merge branch 'drm-forlinus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6 2006-01-12 13:53:40 -08:00
John W. Linville
9f3f46b5fe [PATCH] via-velocity: use NETIF_F_IP_CSUM (hardware only support IPv4)
At least some versions of the via-velocity hardware only support
checksumming IPv4 frames in hardware.  However, the driver is currently
setting the NETIF_F_HW_CSUM flag, which indicates support for more than
just IPv4.  This results in errors when trying to use IPv6 over
via-velocity hardware.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2006-01-12 16:39:45 -05:00