sctp_ulpevent_nofity_peer_addr_change() would be called in
sctp_assoc_set_primary() to send SCTP_ADDR_MADE_PRIM event
when this transport is set to the primary path of the asoc.
This event is described in rfc6458#section-6.1.2:
SCTP_ADDR_MADE_PRIM: This address has now been made the primary
destination address. This notification is provided whenever an
address is made primary.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sctp_ulpevent_nofity_peer_addr_change() is called in
sctp_assoc_rm_peer() to send SCTP_ADDR_REMOVED event
when this transport is removed from the asoc.
This event is described in rfc6458#section-6.1.2:
SCTP_ADDR_REMOVED: The address is no longer part of the
association.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
A helper sctp_ulpevent_nofity_peer_addr_change() will be extracted
to make peer_addr_change event and enqueue it, and the helper will
be called in sctp_assoc_add_peer() to send SCTP_ADDR_ADDED event.
This event is described in rfc6458#section-6.1.2:
SCTP_ADDR_ADDED: The address is now part of the association.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config() are common between dwmac 4.10a [1] and
5.00a [2].
Reuse the same callback for dwmac 4.10a too.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
For detailed timestamping of operations.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl2cu5ATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HYXB/49vT69JJt0wGHR9HOjThnyUHU8s5D2
dJE6lsAbOY8zmGGE5b8yF78fHSA6NrXUWIK6/bNExSfNjwdwrJuVEcxJoi3HtcZA
AWxAvpgR55HETiwudEN5ZxUw6FG5O+XAt0Eh7I4Gd+NaMbKrVDfy/cy3J78NK5Cr
tDsOamv/nuaCVmoXxthU/u4wQTctBSvbeHMJWUePC/TOMnhxBmNrbsv6kDaQoE2A
dWIYjgeUY4s/518Zv//AAhMUsi11N6V3pDyr3MIZJLTh7DDiDgaxx5OUpn6Xgi6Z
vSeq7+elh5C9Ta6yg/DQnk8ZPhrHbFdvUiBps8+u1E/tAo6z70YISfcs
=P2Sr
-----END PGP SIGNATURE-----
Merge tag 'spi-ptp-api' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull in a dependency for Vladimir's work on more precise
packet time stamping.
Mark Brown says:
====================
spi: Add a PTP API
For detailed timestamping of operations.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This reverts commit 0ad646c81b.
As noticed by Jakub, this is no longer needed after
commit 11fc7d5a0a ("tun: fix memory leak in error path")
This no longer exports dev_get_valid_name() for the exclusive
use of tun driver.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
__tipc_nl_compat_dumpit() calls tipc_nl_publ_dump() which expects
the attrs to be available by genl_dumpit_info(cb)->attrs. Add info
struct and attr parsing in compat dumpit function.
Reported-by: syzbot+8d37c50ffb0f52941a5e@syzkaller.appspotmail.com
Fixes: 057af70713 ("net: tipc: have genetlink code to parse the attrs during dumpit")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Huazhong Tan says:
====================
This patch-set includes some new features for the HNS3 ethernet
controller driver.
[patch 01/06] adds support for configuring VF link status on the host.
[patch 02/06] adds support for configuring VF spoof check.
[patch 03/06] adds support for configuring VF trust.
[patch 04/06] adds support for configuring VF bandwidth on the host.
[patch 05/06] adds support for configuring VF MAC on the host.
[patch 06/06] adds support for tx-scatter-gather-fraglist.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The hardware supports up to 8 TX BD for non-tso skb and up to
63 TX BD for TSO skb. Currently, the hns3 driver supports RX skb
with fraglist when HW GRO is enabled, when the stack forwards a
RX skb with fraglist, the stack need to linearize the skb before
sending to other interface without TX fraglist support.
This patch adds support for TX fraglist. The performance increases
from 1 GByte to 1.5 GByte for one iperf TCP stream during
forwarding test after this patch. BTW, the minimum BD number of
ring should be updated to 72 for supporting TX fraglist.
This patch also changes the error handling of some function that
called by hns3_fill_desc, which returns BD num when there is no
error, change some macro to more meaningful name.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support of configuring VF MAC from the host
for the HNS3 driver.
BTW, the parameter init in the hns3_init_mac_addr is
unnecessary now, since the MAC address will not read from
NCL_CONFIG when doing reset, so it should be removed,
otherwise it will affect VF's MAC address initialization.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.
For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:
'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status
'ip link show'
show the setting status
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
There is a spelling mistake in a NL_SET_ERR_MSG_MOD message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Don't populate const arrays on the stack but instead make them
static. Makes the object code smaller by 1058 bytes.
Before:
text data bss dec hex filename
29879 6144 0 36023 8cb7 drivers/net/phy/mscc.o
After:
text data bss dec hex filename
28437 6528 0 34965 8895 drivers/net/phy/mscc.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Don't populate the array exp_mask on the stack but instead make it
static. Makes the object code smaller by 224 bytes.
Before:
text data bss dec hex filename
77832 2290 0 80122 138fa ethernet/netronome/nfp/bpf/jit.o
After:
text data bss dec hex filename
77544 2354 0 79898 1381a ethernet/netronome/nfp/bpf/jit.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
SPI is one of the interfaces used to access devices which have a POSIX
clock driver (real time clocks, 1588 timers etc). The fact that the SPI
bus is slow is not what the main problem is, but rather the fact that
drivers don't take a constant amount of time in transferring data over
SPI. When there is a high delay in the readout of time, there will be
uncertainty in the value that has been read out of the peripheral.
When that delay is constant, the uncertainty can at least be
approximated with a certain accuracy which is fine more often than not.
Timing jitter occurs all over in the kernel code, and is mainly caused
by having to let go of the CPU for various reasons such as preemption,
servicing interrupts, going to sleep, etc. Another major reason is CPU
dynamic frequency scaling.
It turns out that the problem of retrieving time from a SPI peripheral
with high accuracy can be solved by the use of "PTP system
timestamping" - a mechanism to correlate the time when the device has
snapshotted its internal time counter with the Linux system time at that
same moment. This is sufficient for having a precise time measurement -
it is not necessary for the whole SPI transfer to be transmitted "as
fast as possible", or "as low-jitter as possible". The system has to be
low-jitter for a very short amount of time to be effective.
This patch introduces a PTP system timestamping mechanism in struct
spi_transfer. This is to be used by SPI device drivers when they need to
know the exact time at which the underlying device's time was
snapshotted. More often than not, SPI peripherals have a very exact
timing for when their SPI-to-interconnect bridge issues a transaction
for snapshotting and reading the time register, and that will be
dependent on when the SPI-to-interconnect bridge figures out that this
is what it should do, aka as soon as it sees byte N of the SPI transfer.
Since spi_device drivers are the ones who'd know best how the peripheral
behaves in this regard, expose a mechanism in spi_transfer which allows
them to specify which word (or word range) from the transfer should be
timestamped.
Add a default implementation of the PTP system timestamping in the SPI
core. This is not going to be satisfactory performance-wise, but should
at least increase the likelihood that SPI device drivers will use PTP
system timestamping in the future.
There are 3 entry points from the core towards the SPI controller
drivers:
- transfer_one: The driver is passed individual spi_transfers to
execute. This is the easiest to timestamp.
- transfer_one_message: The core passes the driver an entire spi_message
(a potential batch of spi_transfers). The core puts the same pre and
post timestamp to all transfers within a message. This is not ideal,
but nothing better can be done by default anyway, since the core has
no insight into how the driver batches the transfers.
- transfer: Like transfer_one_message, but for unqueued drivers (i.e.
the driver implements its own queue scheduling).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ioana Ciornei says:
====================
dpaa2-eth: misc cleanup
This patch set consists of some cleanup patches ranging from removing dead
code to fixing a minor issue in ethtool stats. Also, unbounded while loops
are removed from the driver by adding a maximum number of retries for DPIO
portal commands.
Changes in v2:
- return -ETIMEDOUT where possible if the number of retries is hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.
Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.
Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print error message for a successful return value.
Fixes: d84c3a4ded ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one function call whose result was not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array tick_array on the stack but instead make it
static. Makes the object code smaller by 29 bytes.
Before:
text data bss dec hex filename
19191 432 0 19623 4ca7 hisilicon/hns3/hns3pf/hclge_tm.o
After:
text data bss dec hex filename
19098 496 0 19594 4c8a hisilicon/hns3/hns3pf/hclge_tm.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the arrays port_map and sl_map on the stack but
instead make them static. Makes the object code smaller by 64 bytes.
Before:
text data bss dec hex filename
49575 6872 64 56511 dcbf hisilicon/hns/hns_dsaf_main.o
After:
text data bss dec hex filename
49350 7032 64 56446 dc7e hisilicon/hns/hns_dsaf_main.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net/tls: minor micro optimizations
This set brings a number of minor code changes from my tree which
don't have a noticeable impact on performance but seem reasonable
nonetheless.
First sk_msg_sg copy array is converted to a bitmap, zeroing that
structure takes a lot of time, hence we should try to keep it
small.
Next two conditions are marked as unlikely, GCC seemed to had
little trouble correctly reasoning about those.
Patch 4 adds parameters to tls_device_decrypted() to avoid
walking structures, as all callers already have the relevant
pointers.
Lastly two boolean members of TLS context structures are
converted to a bitfield.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a single bit instead of boolean to remember if packet
was already decrypted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store async_capable on a single bit instead of a full integer
to save space.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary pointer chasing and calculations, callers already
have most of the state tls_device_decrypted() needs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure GCC realizes it's unlikely that allocations will fail.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tell GCC sk->err is not likely to be set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use bool array in struct sk_msg_sg, save 12 bytes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper skb_ensure_writable in two more places to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function de-facto returns a bool, so let's change the return type
accordingly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sameeh Jubran says:
====================
ena: Support ethtool set_channels
Difference from v2:
* ethtool's set/get channels: Switched to using combined instead of
separate rx/tx
* Fixed error handling in set_channels
* Fixed indentation and cosmetic issues as requested by Jakub Kicinski
Difference from v1:
* Dropped the print from patch 0002 - "net: ena: multiple queue creation
related cleanups" as requested by David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Set channels callback enables the user to change the count of queues
used by the driver using ethtool. We decided to currently support only
equal number of rx and tx queues, this might change in the future.
Also rename dev_up to dev_was_up in ena_update_queue_count() to make
it clearer.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of queues can be derived using ethtool, no need to print
it in ena_probe()
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update ena_ethtool:ena_get_channels() to return adapter->max_io_queues
so that ethtool -l returns the correct maximum queue number.
- Change the name of ena_calc_io_queue_num() to
ena_calc_max_io_queue_num() as it returns the maximum number of io
queues and actual number of queues can be smaller if changed
by ethtool -L which is implemented in a later commit.
- Change variable name from io_queue_num to max_num_io_queues in
ena_calc_max_io_queue_num() and ena_probe().
- Make all types of variables that convey the number and sizeof queues
to be u32, for consistency with the API between the driver and the
device.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use the same IRQ and NAPI to service RX and TX then we need to
use a combined channel instead of rx and tx channels.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rename ena_calc_queue_size() to ena_calc_io_queue_size() for clarity
and consistency
- Remove redundant number of io queues parameter in functions
ena_enable_msix() and ena_enable_msix_and_set_admin_interrupts(),
which already get adapter parameter, so use adapter->num_io_queues
in the function instead.
- Use the local variable ena_dev instead of ctx->ena_dev in
ena_calc_io_queue_size
- Fix multi row comment alignments
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most places in the code refer to the IO queues as io_queues and not
simply queues. Examples - max_io_queues_per_vf, ENA_MAX_NUM_IO_QUEUES,
ena_destroy_all_io_queues() etc..
We are also adding the new max_num_io_queues field to struct ena_adapter
in the following commit.
The changes included in this commit are:
struct ena_adapter->num_queues => struct ena_adapter->num_io_queues
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel T. Lee says:
====================
samples: pktgen: allow to specify destination IP range
Currently, pktgen script supports specify destination port range.
To further extend the capabilities, this commit allows to specify destination
IP range with CIDR when running pktgen script.
Specifying destination IP range will be useful on various situation such as
testing RSS/RPS with randomizing n-tuple.
This patchset fixes the problem with checking the command result on proc_cmd,
and add feature to allow destination IP range.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, kernel pktgen has the feature to specify destination
address range for sending packet. (e.g. pgset "dst_min/dst_max")
But on samples, each pktgen script doesn't have any option to achieve this.
This commit adds the feature to specify the destination address range with CIDR.
-d : ($DEST_IP) destination IP. CIDR (e.g. 198.18.0.0/15) is also allowed
# ./pktgen_sample01_simple.sh -6 -d fe80::20/126 -p 3000 -n 4
# tcpdump ip6 and udp
05:14:18.082285 IP6 fe80::99.71 > fe80::23.3000: UDP, length 16
05:14:18.082564 IP6 fe80::99.43 > fe80::23.3000: UDP, length 16
05:14:18.083366 IP6 fe80::99.107 > fe80::22.3000: UDP, length 16
05:14:18.083585 IP6 fe80::99.97 > fe80::21.3000: UDP, length 16
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds CIDR parsing and IP validate helper function to parse
single IP or range of IP with CIDR. (e.g. 198.18.0.0/15)
Validating the address should be preceded prior to the parsing.
Helpers will be used in prior to set target address in samples/pktgen.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, proc_cmd is used to dispatch command to 'pg_ctrl', 'pg_thread',
'pg_set'. proc_cmd is designed to check command result with grep the
"Result:", but this might fail since this string is only shown in
'pg_thread' and 'pg_set'.
This commit fixes this logic by grep-ing the "Result:" string only when
the command is not for 'pg_ctrl'.
For clarity of an execution flow, 'errexit' flag has been set.
To cleanup pktgen on exit, trap has been added for EXIT signal.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit changes variable names that can cause confusion.
For example, variable DST_MIN is quite confusing since the
keyword 'udp_dst_min' and keyword 'dst_min' is used with pg_ctrl.
On the following commit, 'dst_min' will be used to set destination IP,
and the existing variable name DST_MIN should be changed.
Variable names are matched to the exact keyword used with pg_ctrl.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
netdevsim: implement devlink dev_info op
Initial implementation of devlink dev_info op - just driver name is
filled up and sent to user. Bundled with selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify netdevsim driver name returned by devlink dev info.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
