Assume that the boot loader knows the physical memory of the system and
deduce that information from the contents of the SDRAM control register.
It is still possible to override with with the "mem=" parameter, but we
have a sensible default now.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634u are using minuses between the blocks
of the MAC address and other devices are using colons to separate them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2366/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.
The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some embedded devices like the Netgear WNDR3300 have two SSB based cards
without an own sprom on the pci bus. We have to provide two different
fallback sproms for these and this was not possible with the old solution.
In the bcm47xx architecture the sprom data is stored in the nvram in the
main flash storage. The architecture code will be able to fill the sprom
with the stored data based on the bus where the device was found.
The bcm63xx code should do the same thing as before, just using the new
API.
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
According to the databooks, the Au1000 DMA engine must be programmed with
the physical FIFO addresses. This patch does that; furthermore this
opened the possibility to get rid of a lot of now unnecessary address
defines.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Rewrite ethernet setup to use runtime cpu detection, and also clean up
the ethernet base address mess as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the PM sysdev to use syscore_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
replace au_readl/au_writel with __raw_readl/__raw_writel,
and clean up IC-related stuff from the headers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a build failure with gpio_keys and CONFIG_GPIOLIB=n (mtx1):
CC drivers/input/keyboard/gpio_keys.o
gpio_keys.c: In function 'gpio_keys_report_event':
gpio_keys.c:325:2: error: implicit declaration of function 'gpio_get_value_cansleep'
gpio_keys.c: In function 'gpio_keys_setup_key':
gpio_keys.c:390:3: error: implicit declaration of function 'gpio_set_debounce'
Also add stubs for the other new functions.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2346/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the driver for the ETOP Packet Processing Engine (PPE32)
found inside the XWAY family of Lantiq MIPS SoCs. This driver makes 100MBit
ethernet work. Support for all 8 dma channels, gbit and the embedded switch
found on the ar9/vr9 still needs to be implemented.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2357/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the DMA engine found inside the XWAY family of
SoCs. The engine has 5 ports and 20 channels.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XWAY family allows to extend the number of gpios by using shift
registers or latches. This patch adds the 2 drivers needed for this. The
extended gpios are output only.
[ralf@linux-mips.org: Fixed ltq_stp_probe section() attributes.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2258/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the driver/map for NOR devices attached to the SoC via the
External Bus Unit (EBU).
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/2285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.
The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the Lantiq XWAY family of Mips24KEc SoCs.
* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)
The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.
The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function
int lq_gpio_request(unsigned int pin, unsigned int alt0,
unsigned int alt1, unsigned int dir, const char *name);
which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.
The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add initial support for Mips based SoCs made by Lantiq. This series will add
support for the XWAY family.
The series allows booting a minimal system using a initramfs or NOR. Missing
drivers and support for Amazon and GPON family will be provided in a later
series.
[Ralf: Remove some cargo cult programming and fixed formatting.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2252/
Patchwork: https://patchwork.linux-mips.org/patch/2371/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable XLR CPU support, SMP, initramfs based root filesystem etc.
[ralf@linux-mips.org: shrink the defconfig file through make savedefconfig.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add NLM_XLR_BOARD, CPU_XLR and other config options
Makefile updates, mostly based on r4k
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* include/asm/netlogic added with files common for all Netlogic processors
(common with XLP which will be added later)
* include/asm/netlogic/xlr for XLR/XLS chip specific files
* netlogic/xlr for XLR/XLS platform files
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_XLR case added to mm/tlbex.c
CPU_XLR case added to mm/c-r4k.c for PINDEX attribute
Feature overrides for XLR cpu.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add Netlogic Microsystems company ID and processor IDs for XLR
and XLS processors for CPU probe. Add CPU_XLR to cpu_type_enum.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2367/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It seems that Adrian is getting old. He removed almost everything of
GEMINI in commit c53653130 ("[POWERPC] Remove the broken Gemini
support") except this piece.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[See http://lists.ozlabs.org/pipermail/linuxppc-dev/2010-October/086424.html
and followups. Part of the commit message is directly copied from that.]
Commit 540c6c392f tries to find i8042 IRQs in
the device-tree but doesn't fall back to the old hardcoded 1 and 12 in all
failure cases.
Specifically, the case where the device-tree contains nothing matching
pnpPNP,303 or pnpPNP,f03 doesn't seem to be handled well. It sort of falls
through to the old code, but leaves the IRQs set to 0.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We keep track of the size of the lowest block of memory and call
setup_initial_memory_limit() only after we've parsed them all
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
When using a property refering to the availibily of dynamic dma windows
call it ddw_avail not ddr_avail.
dupe_ddw_if_already_created does not dupilcate anything, it only finds
and reuses the windows we already created, so rename it to
find_existing_ddw. Also, it does not need the pci device node, so
remove that argument.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No functional changes requires that we eat errors from strtobool.
If people want to not do this, then it should be fixed at a later date.
V2: Simplification suggested by Rusty Russell removes the need for
additional variable ret.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Move the discovery of windows previously setup from when the pci driver
calls set_dma_mask to an arch_initcall.
When kexecing into a kernel with dynamic dma windows allocated, we need
to find the windows early so that memory hot remove will be able to
delete the tces mapping the to be removed memory and memory hotplug add
will map the new memory into the window. We should not wait for the
driver to be loaded and the device to be probed. The iommu init hooks
are before kmalloc is setup, so defer to arch_initcall.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
