Correct race condition where ioaccel is re-enabled before the raid_map is
updated. For RAID_1, RAID_1ADM, and RAID 5/6 there is a BUG_ON called which
is bad.
- Change event thread to disable ioaccel only. Send all requests down the
RAID path instead.
- Have rescan thread handle offload_enable.
- Since there is only one rescan allowed at a time, turning
offload_enabled on/off should not be racy. Each handler queues up a
rescan if one is already in progress.
- For timing diagram, offload_enabled is initially off due to a change
(transformation: splitmirror/remirror), ...
otbe = offload_to_be_enabled
oe = offload_enabled
Time Event Rescan Completion Request
Worker Worker Thread Thread
---- ------ ------ ---------- -------
T0 | | + UA |
T1 | + rescan started | 0x3f |
T2 + Event | | 0x0e |
T3 + Ack msg | | |
T4 | + if (!dev[i]->oe && | |
T5 | | dev[i]->otbe) | |
T6 | | get_raid_map | |
T7 + otbe = 1 | | |
T8 | | | |
T9 | + oe = otbe | |
T10 | | | + ioaccel request
T11 * BUG_ON
T0 - I/O completion with UA 0x3f 0x0e sets rescan flag.
T1 - rescan worker thread starts a rescan.
T2 - event comes in
T3 - event thread starts and issues "Acknowledge" message
...
T6 - rescan thread has bypassed code to reload new raid map.
...
T7 - event thread runs and sets offload_to_be_enabled
...
T9 - rescan thread turns on offload_enabled.
T10- request comes in and goes down ioaccel path.
T11- BUG_ON.
- After the patch is applied, ioaccel_enabled can only be re-enabled in
the re-scan thread.
Link: https://lore.kernel.org/r/158472877894.14200.7077843399036368335.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXbN1gSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWUzAP4tB9Z+
X5zfnMLmeAtSCnVwIgFX3/GVSFfzEmi+3VxfBQEA3nfs5AAJCPsaTk9z+jLtAKPk
6uYoHwsyTHal19Ojt9g=
=IOPn
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
Correct returning from reset before outstanding commands are completed
for the device.
Link: https://lore.kernel.org/r/157107623870.17997.11208813089704833029.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Seven fixes to four drivers with no core changes. The mpt3sas one is
theoretical until we get a CPU that goes up to 64 bits physical, the
qla2xxx one fixes an oops in a driver initialization error leg and the
others are mostly cosmetic.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXURSriYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWpKAQCbTaKz
AWOXWaMUoL26nZ036slYx9KjxcXS/MFuDXCAnQEA5ww+AfKurovX62i3B7YqVDxm
j0TBq+LvzUUNcrA+JU8=
=NfZ0
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes to four drivers with no core changes.
The mpt3sas one is theoretical until we get a CPU that goes up to 64
bits physical, the qla2xxx one fixes an oops in a driver
initialization error leg and the others are mostly cosmetic"
[ The fcoe patches may be worth highlighting - they may be "just"
cleanups, but they simplify and fix the odd fc_rport_priv structure
handling rules so that the new gcc-9 warnings about memset crossing
structure boundaries are gone.
The old code was hard for humans to understand too, and really
confused the compiler sanity checks - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix possible fcport null-pointer dereferences
scsi: mpt3sas: Use 63-bit DMA addressing on SAS35 HBA
scsi: hpsa: remove printing internal cdb on tag collision
scsi: hpsa: correct scsi command status issue after reset
scsi: fcoe: pass in fcoe_rport structure instead of fc_rport_priv
scsi: fcoe: Embed fc_rport_priv in fcoe_rport structure
scsi: libfc: Whitespace cleanup in libfc.h
Remove racy printing of internal commands. Completion thread can be
cleaning up the command in parallel.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some files got renamed but probably due to some merge conflicts,
a few references still point to the old locations.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Currently the check for a lockup_detected failure exits via the label
return_reset_status that reads and dereferences an uninitialized pointer
dev. Fix this by ensuring dev is inintialized to null.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: 14991a5bade5 ("scsi: hpsa: correct device resets")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: wrong baseline, applied by hand]
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a race condition that occurs between the reset handler and the
completion handler. There are times when the wait_event condition is
never met due to this race condition and the reset never completes.
The reset_pending field is NULL initially.
t Reset Handler Thread Completion Thread
-- -------------------- -----------------
t1 if (c->reset_pending)
t2 c->reset_pending = dev; if (atomic_dev_and_test(counter))
t3 atomic_inc(counter) wait_up_all(event_sync_wait_queue)
t4
t5 wait_event(...counter == 0)
Kernel.org Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=1994350
Bug 199435 - HPSA + P420i resetting logical Direct-Access
never complete
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Close up a rare multipath issue.
Close up small hole where a command completes after a device has been
removed from SML and before the device is re-added.
- Mark device as removed in slave_destroy
- Do not complete commands for deleted devices
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wait longer for outstanding commands before removing a multipath
device. Increase the timeout value for ptraid commands.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct rare multipath issue where a device is deleted with an
outstanding cmd which results in a tag collision.
The cmd eventually completes. If a collision is detected wait until
the command slot is cleared.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid system stalls by switching to local workqueue.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct issue with hpsa_simple_mode module parameter. Driver was
hanging due to incorrect interrupt setup.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some documentation files were still pointing to the old place.
Fixes: 229b4e0728 ("Documentation: PCI: convert pci.txt to reST")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- set ioaccel2_sg_element member 'chain_indicator' to IOACCEL2_LAST_SG for
the last s/g element.
- set ioaccel2_sg_element member 'chain_indicator' to IOACCEL2_CHAIN when
chaining.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are times when a TUR can take longer than the DEFAULT_TIMEOUT
value. The timeout code is not correct as the function exits with an
automatic as the completion variable...To be fixed later.
Remove the TUR timeout.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a 'rare' race condition where a disk is failed after a device list
has been obtained from the controller and before attempting to get the
device id.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Multipath failures are normally detected at the frequency of the event
thread. Detect LUN failures earlier by checking request completion status.
Reviewed-by: Bader Ali-saleh <bader.ali-saleh@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns several times in the scsi subsystem (trimmed for brevity):
drivers/scsi/hpsa.c:6209:7: warning: overflow converting case value to
switch condition type (2147762695 to 18446744071562347015) [-Wswitch]
case CCISS_GETBUSTYPES:
^
drivers/scsi/hpsa.c:6208:7: warning: overflow converting case value to
switch condition type (2147762694 to 18446744071562347014) [-Wswitch]
case CCISS_GETHEARTBEAT:
^
The root cause is that the _IOC macro can generate really large numbers,
which don't fit into type 'int', which is used for the cmd parameter in
the ioctls in scsi_host_template. My research into how GCC and Clang are
handling this at a low level didn't prove fruitful. However, looking at
the rest of the kernel tree, all ioctls use an 'unsigned int' for the
cmd parameter, which will fit all of the _IOC values in the scsi/ata
subsystems.
Make that change because none of the ioctls expect a negative value for
any command, it brings the ioctls inline with the reset of the kernel,
and it removes ambiguity, which is never good when dealing with compilers.
Link: https://github.com/ClangBuiltLinux/linux/issues/85
Link: https://github.com/ClangBuiltLinux/linux/issues/154
Link: https://github.com/ClangBuiltLinux/linux/issues/157
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 1195463 ("Missing break in switch")
Addresses-Coverity-ID: 1195464 ("Missing break in switch")
Addresses-Coverity-ID: 1195465 ("Missing break in switch")
Addresses-Coverity-ID: 1195466 ("Missing break in switch")
Addresses-Coverity-ID: 1357338 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas. In addition there's a set of mostly
small updates to the target subsystem a set of conversions to the
generic DMA API, which do have some potential for issues in the older
drivers but we'll handle those as case by case fixes. A new myrs for
the DAC960/mylex raid controllers to replace the block based DAC960
which is also being removed by Jens in this merge window. Plus the
usual slew of trivial changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9BQJSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU3MAP41T8yW
UJQDCprj65pCR+9mOUWzgMvgAW/15ouK89x/7AD/XAEQZqoAgpFUbgnoZWGddZkS
LykIzSiLHP4qeDOh1TQ=
=2JMU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Don Brace <don.brace@microchip.com>
Acked-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vmemdup_user is better than duplicating its implementation, So just replace
the open code.
The issue is detected with the help of Coccinelle.
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
e2c7b43 was supposed to limit transfer length to 1MB, but got the unit of
max_sectors wrong.
Fixes: e2c7b433f7 ("scsi: hpsa: limit transfer length to 1MB")
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The original complaint was the lsscsi -t showed the same SAS address of the
two enclosures (SEP devices). In fact the SAS address was being set to the
Enclosure Logical Identifier (ELI).
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWyHBVCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishTkjAPoDF71y
5+w0pim7HQvyo02GxKRWyYzkibZsTfNQ49Yo6wD9EhKp1OD4TIrO1ey3fHpCcYry
CHfUIClnev6hiqDBDrI=
=xJ+K
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Mask off Scope bits in retry delay
scsi: qla2xxx: Fix crash on qla2x00_mailbox_command
scsi: aic7xxx: aic79xx: fix potential null pointer dereference on ahd
scsi: mpt3sas: Add an I/O barrier
scsi: qla2xxx: Fix setting lower transfer speed if GPSC fails
scsi: hpsa: disable device during shutdown
scsi: sd_zbc: Fix sd_zbc_check_zone_size() error path
scsi: aacraid: remove bogus GFP_DMA32 specifies
'Commit cc27b735ad ("PCI/portdrv: Turn off PCIe services during
shutdown")' has been added to kernel to shutdown pending PCIe port service
interrupts during reboot so that a newly started kexec kernel wouldn't
observe pending interrupts.
pcie_port_device_remove() is disabling the root port and switches by
calling pci_disable_device() after all PCIe service drivers are shutdown.
This has been found to cause crashes on HP DL360 Gen9 machines during
reboot due to hpsa driver not clearing the bus master bit during the
shutdown procedure by calling pci_disable_device().
Disable device as part of the shutdown sequence.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199779
Fixes: cc27b735ad ("PCI/portdrv: Turn off PCIe services during shutdown")
Cc: stable@vger.kernel.org
Reported-by: Ryan Finnie <ryan@finnie.org>
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two driver fixes (ibmvfc, iscsi_tcp) and a USB fix for devices that
give the wrong return to Read Capacity and cause a huge log spew. The
remaining 5 patches all try to fix commit 84676c1f21
"genirq/affinity: assign vectors to all possible CPUs") which broke
the non-mq I/O path.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWrpSmyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishY+MAP9Zvin/
AUc3xkvOPdIzRPp2aXQHJKC+NGmNFr6MiXIHiAD/TvjbkxEjbUTjnr+gZNaloDma
d/I4i9xaBNSvqNJpzT0=
=mLIX
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two driver fixes (ibmvfc, iscsi_tcp) and a USB fix for devices that
give the wrong return to Read Capacity and cause a huge log spew.
The remaining five patches all try to fix commit 84676c1f21
("genirq/affinity: assign vectors to all possible CPUs") which broke
the non-mq I/O path"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi_tcp: set BDI_CAP_STABLE_WRITES when data digest enabled
scsi: sd: Remember that READ CAPACITY(16) succeeded
scsi: ibmvfc: Avoid unnecessary port relogin
scsi: virtio_scsi: unify scsi_host_template
scsi: virtio_scsi: fix IO hang caused by automatic irq vector affinity
scsi: core: introduce force_blk_mq
scsi: megaraid_sas: fix selection of reply queue
scsi: hpsa: fix selection of reply queue
Since commit 84676c1f21 ("genirq/affinity: assign vectors to all
possible CPUs") we could end up with an MSI-X vector that did not have
any online CPUs mapped. This would lead to I/O hangs since there was no
CPU to receive the completion.
Retrieve IRQ affinity information using pci_irq_get_affinity() and use
this mapping to choose a reply queue.
[mkp: tweaked commit desc]
Cc: Hannes Reinecke <hare@suse.de>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Artem Bityutskiy <artem.bityutskiy@intel.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Fixes: 84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Tested-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Using this extension reduces the object size.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hpsa_show_dev_msg prints other information and a newline after the
message string, so the message string does not need to include a newline
explicitly. Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
device->scsi3addr[] is an array, not a pointer, so it can't be NULL.
I've removed the check.
[mkp: fixed typo]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for enclosure logical identifier
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suggested-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
