The DT binding for tildc is not consistent with the driver code: there
are two options - 'max-width' and 'max-pixelclock' specified in the
documentation which are parsed as 'ti,max-width' and
'ti,max-pixelclock' respectively.
Make the driver code consistent with the binding.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Configure video mode to HW in enable() call back. There is no reason
to do it before that. This makes PM functions way easier because there
is no HW context to save when screen is for instance blanked. This
patch removes mode_set_nofb() call back from tilcdc.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Failed tilcdc_crtc_create() error handling was broken, this patch
should fix it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Adds drm bride support for attaching drm bridge drivers to tilcdc. The
decision whether a video port leads to an external encoder or bridge
is made simply based on remote device's compatible string. The code
has been tested with BeagleBone-Black with and without BeagleBone
DVI-D Cape Rev A3 using ti-tfp410 driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix race from forced shutdown of crtc in unload by adding internal
locking and a boolean telling if device is going to be shutdown.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Use unload to handle initialization failures instead of complex goto
label mess. To do this the initialization sequence needed slight
reordering and some unload functions needed to become conditional.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Stop using struct drm_driver load() and unload() callbacks. The
callbacks should not be used anymore. Instead of using load the
drm_device is allocated with drm_dev_alloc() and registered with
drm_dev_register() only after the driver is completely initialized.
The deinitialization is done directly either in component unbind
callback or in platform driver demove callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Due to some potential tweaks for the da850 LCDC (for example: the
required memory bandwith settings) we need a separate compatible
for the IP present on the da850 boards.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
drm_atomic_state has a complicated single owner model that tracks the
single reference from allocation through to destruction on another
thread - or perhaps on a local error path. We can simplify this tracking
by using reference counting (at a cost of a few more atomics). This is
even more beneficial when the lifetime of the state becomes more
convoluted than being passed to a single worker thread for the commit.
v2: Double check !intel atomic_commit functions for missing gets
v3: Update kerneldocs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161014121833.439-27-chris@chris-wilson.co.uk
When 'component_bind_all' fails it should not try to unbind components
in the error handling. This will produce a null pointer kernel panic when
no component exist.
This patch changes the order of the error handling. Now, it will only
unbind components if the are bound. Otherwise, the module will jump to
an error label below.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Fixes the following sparse warning:
drivers/gpu/drm/tilcdc/tilcdc_drv.c:64:5: warning:
symbol 'tilcdc_atomic_check' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Remove unnecessary tilcdc_crtc_disable() from tilcdc_unload(). The
tilcdc_crtc_disable() called via tilcdc_crtc_destroy() by
drm_mode_config_cleanup() couple of lines later.
The early call to tilcdc_crtc_disable() was a wrong fix (that worked)
for calling drm_flip_work_cleanup() before flushing the flip-work
queue.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up LCDC functional clock rate setting code.
The LCDC functional clock is set by two functions: mode_set_nofb() and
cpufreq_transition().
When tilcdc_crtc_mode_set_nofb() is called in atomic commit phase the
drm atomic helpers have taken all the necessary drm locks and turned
off the crtc, while tilcdc_commit() is keeping LCDC powered on. For
mode_set_nofb() just a simple clock setting function without any
locking or power management code is enough. The new tilcdc_crtc_set_clk()
is implemented for that purpose.
cpufreq_transition() on the other hand is called from outside DRM and
it needs to take the necessary locks and turn off the CRTC while
keeping the LCDC powered. The reimplemented tilcdc_crtc_update_clk()
is for that purpose and it uses the new tilcdc_crtc_set_clk() to
actually set the clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Take crtc modeset lock while updating the crtc clock rate. To avoid a
race in tilcdc_crtc_update_clk(), we do not want crtc mode to change
while we update crtc clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Choose console BPP that supports RGB and remove the old fbdev bpp
selection code. LCDC on AM335x has red and blue wires switched between
24 bit and 16 bit colors. If 24 format is wired for RGB colors, the 16
bit format is wired for BGR. drm_fbdev_cma_init() does not currently
like anything else but RGB formats, so we must choose such bytes per
pixel value that supports RGB.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "blue-and-red-wiring"-device tree property and update devicetree
binding document.
The red and blue components are reversed between 24 and 16 bit modes
on am335x LCDC output pins. To get 24 RGB format the red and blue
wires has to be crossed and this in turn causes 16 colors output to be
in BGR format. With straight wiring the 16 color is RGB and 24 bit is
BGR.
The new property describes whether the red and blue wires are crossed
or not. If the property is not present or its value is not recognized
the legacy mode is assumed. The legacy configuration supports RGB565,
RGB888 and XRGB8888 formats. However, depending on wiring, the red and
blue colors are swapped in either 16 or 24-bit color modes.
For more details see section 3.1.1 in AM335x Silicon Errata:
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
drm_helper_disable_unused_functions() should not be called by atomic
drivers.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
Get rid of legacy dpms mechanism. This simplifies the code quite a
bit. The old start() and stop() functions become tilcdc_crtc_enable()
and *_disable(). The functions are added with all the necessary
mechanisms from the old dpms function and they are used directly as
the crtc helper enable() and disable() callbacks.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Use drm_atomic_helper_resume/suspend() and get rid off all the obsolete
register level context restoring code.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Enable and disable interrupts in crtc start() and stop(). None of the
interrupts can fire if CRTC is disabled, so it is cleaner - when
considering suspend/resume code etc. - to enable the interrupts when
CRTC is turned on and to disable them when CRTC is turned off.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Set DRIVER_ATOMIC and use atomic helpers and rename commit and prepare
crtc helpers to enable and disable. This makes the final jump to mode
setting, but there is lot of obsolete code to clean up.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add drm_mode_config_reset() call to tilcdc_load(). This is need to
initialize atomic state variables at load time.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Add atomic mode config funcs. The atomic_commit implementation is a
copy-paste from drm_atomic_helper_commit(), leaving out the async
test. The similar copy-paste implementation appears to be used in many
other drivers too. The standard drm_atomic_helper_check() is used for
checking.
The drm_atomic_helper_check() can not be used in drm_mode_config_funcs
atomic_check() callback because the plane's check implementation may
update crtc state's ->mode_changed flag. Because of this the
drm_atomic_helper_check_modeset() has to be called once more after
drm_atomic_helper_check_planes() (see drm_atomic_helper_check_modeset()
documentation).
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Fix tilcdc component master unloading. If a subcomponent module
(tda998x in this case) is unloaded before its master (tilcdc in this
case), it calls drm_put_dev() and it should not be called again by
the master when its module is unloaded. However component_master_del()
must still be called and the check if the drm_put_dev() has been
called must be in component_master_ops unbind() callback, not in
platform_driver remove() callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Restore old dpms state in pm_resume(). The dpms is turned off in
pm_suspend() and it should be restored to its original state in
pm_resume(). Without this patch the display is left blanked after a
suspend/resume cycle.
Fixes commit 614b3cfeb8 ("drm/tilcdc: disable the lcd controller/dma
engine when suspend invoked")
Signed-off-by: Jyri Sarha <jsarha@ti.com>
We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.
Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.
While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.
v2: Make drm_dev_set_unique static and update kerneldoc.
v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.
v4: Drop accidental amdgpu hunk (Emil).
v5: Drop accidental omapdrm vblank counter change (Emil).
v6: Rebase on top of the sphinx conversion.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use devm_kzalloc() and devm_kcalloc() for private data allocation at
driver load time.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add ratelimited prints on sync lost and FIFO underrun interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes the duplicate LCDC_INT_ENABLE_SET_REG-entry in registers array.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix interrupt enable/disable code for version 2 tilcdc. In version 2
tilcdc there is a separate register for disabling interrupts. Writing
0 to enable registers bits does not have any effect. The interrupt
clear register works the same way, writing 1 to specific bit disables
the interrupt and writing 0 does not have any effect.
The "bug" that is fixed here does not really do any harm since the
interrupts are enabled only once in the power up and disabled before
power down.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Get rid of complex ping-pong mechanism and replace it with simpler
single buffer flipping code.
The LCDC HW appears to be designed mainly static framebuffers in
mind. There are two modes of operation, either static single buffer,
or ping pong double buffering with two static buffers switching back
and forth. Luckily the framebuffer start address is fetched only in
the beginning of the frame and changing the address after that only
takes effect after the next vertical blank. The page flipping code can
simply write the address of the new framebuffer and the page is
flipped automatically after the next vertical blank. Using the ping
pong double buffering makes the flipping code way more complex and it
does not provide any benefit, so it is better to switch to single
buffer operation.
There is still one problem in updating the framebuffer dma address on
the fly. There are two registers defining the framebuffer dma area and
things may break if the dma address is fetched in while the registers
are are being updated.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Disable crtc on unload. Call tilcdc_crtc_dpms() with DRM_MODE_DPMS_OFF
in the beginning of unload function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Cleanup runtime PM handling. Before the patch the usage of pm_runtime
calls was inconsistent and hard to follow. After the update the
pm_runtime calls are removed from set_scanout() and called around
major operations that access the HW. After the patch the DPMS code does
not have pm_runtime_forbid/allow calls any more and
pm_runtime_irq_safe() is not set anymore.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Allocate suspend/resume register storage based on the actual number
registers the driver is aware of. The static allocation for register
storage had fallen behind badly.
Reported-by: Michael Bode <michael@bumbleB.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix build error when !CONFIG_CPU_FREQ
drivers/gpu/drm/tilcdc/tilcdc_drv.c: In function 'tilcdc_load':
drivers/gpu/drm/tilcdc/tilcdc_drv.c:327:1: error: label 'fail_put_clk' defined but not used [-Werror=unused-label]
fail_put_clk:
^
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is nothing special about tilcdc HW when the video memory is
concerned. Just using the standard drm helpers for implementation is
enough.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The LCD controller must be deactivated and all DMA transactions stopped
when the suspend power state is entered otherwise the PRCM causes the L3
bus to get stuck in transition state.
This commit forces the lcdc to be shut down and waits for all pending DMA
transactions to complete as part of the suspend handler for this driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The frame_done interrupt was only being enabled when the vsync
interrupts were being enabled by DRM. However the frame_done is
used to determine if the LCD controller has successfully completed
the raster_enable, raster_disable commands and the vsync interrupts
are not always enabled during these operations.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On BeagleBone Black if no HDMI monitor is connected and suspend
is requested a kernel panic will result:
root@am335x-evm:~# echo mem > /sys/power/state
[ 65.548710] PM: Syncing filesystems ... done.
[ 65.631311] Freezing user space processes ... (elapsed 0.006 seconds) done.
[ 65.648619] Freezing remaining freezable tasks ... (elapsed 0.005 seconds) done.
[ 65.833500] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa30e004
[ 65.841692] Internal error: : 1028 [#1] SMP ARM
<snip>
[ 66.105287] [<c03765f0>] (platform_pm_suspend) from [<c037b6d4>] (dpm_run_callback+0x34/0x70)
[ 66.114370] [<c037b6d4>] (dpm_run_callback) from [<c037ba84>] (__device_suspend+0x10c/0x2f4)
[ 66.123357] [<c037ba84>] (__device_suspend) from [<c037d004>] (dpm_suspend+0x58/0x218)
[ 66.131796] [<c037d004>] (dpm_suspend) from [<c008d948>] (suspend_devices_and_enter+0x9c/0x3c0)
[ 66.141055] [<c008d948>] (suspend_devices_and_enter) from [<c008de7c>] (pm_suspend+0x210/0x24c)
[ 66.150312] [<c008de7c>] (pm_suspend) from [<c008cabc>] (state_store+0x68/0xb8)
[ 66.158103] [<c008cabc>] (state_store) from [<c02e9654>] (kobj_attr_store+0x14/0x20)
[ 66.166355] [<c02e9654>] (kobj_attr_store) from [<c0185c70>] (sysfs_kf_write+0x4c/0x50)
[ 66.174883] [<c0185c70>] (sysfs_kf_write) from [<c018926c>] (kernfs_fop_write+0xb4/0x150)
[ 66.183598] [<c018926c>] (kernfs_fop_write) from [<c0122638>] (vfs_write+0xa8/0x180)
[ 66.191846] [<c0122638>] (vfs_write) from [<c01229f8>] (SyS_write+0x40/0x8c)
[ 66.199365] [<c01229f8>] (SyS_write) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 66.207426] Code: e595c210 e5932000 e59cc000 e08c2002 (e592c000)
This is because the lcdc module is not enabled when no monitor is detected
to save power. However the suspend handler just blindly tries to save the
lcdc state by copying out the pertinent registers. However module is off
so no good things happen when you try and access it.
This patch only saves off the registers if the module is enabled, and
then only restores the registers on resume if they were saved off during
suspend.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Update tilcdc driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Updating the tilcdc DRM driver code to calculate the LCD controller
pixel clock more accurately. Based on a suggested implementation by
Tomi Valkeinen.
The current code does not work correctly and produces wrong results
with many requested clock rates. It also oddly uses two different
clocks, a display pll clock and a divider clock (child of display
pll), instead of just using the clock coming to the lcdc.
This patch removes the use of the display pll clock, and rewrites the
code to calculate the clock rates. The idea is simply to request a
clock rate of pixelclock*2, as the LCD controller has an internal
divider which we set to 2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
[Rewrapped description]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Again since the drm core takes care of event unlinking/disarming this
is now just needless code.
v2: Fixup misplaced hunks.
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-13-git-send-email-daniel.vetter@ffwll.ch
The drm_fbdev_cma_init function always calls the
drm_helper_disable_unused_functions. Since it's part of the usual probe
process, all the drivers using that helper will end up having their encoder
and CRTC disable functions called at probe if their device has not been
reported as enabled.
This could be fixed by reading out from the registers the current state of
the device if it is enabled, but even that will not handle the case where
the device is actually disabled.
Moreover, the drivers using the atomic modesetting expect that their enable
and disable callback to be called when the device is already enabled or
disabled (respectively).
We can however fix this issue by moving the call to
drm_helper_disable_unused_functions out of drm_fbdev_cma_init and make the
drivers needing it (all the drivers calling drm_fbdev_cma_init and not
using the atomic modesetting) explicitly call it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452785109-6172-14-git-send-email-maxime.ripard@free-electrons.com
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
tilcdc calls runtime PM get/put functions everywhere. Some of those
places will be called in irq context, crashing the driver.
As a quick fix, use pm_runtime_irq_safe() for tilcdc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
