Remove old ddp code from cxgb3i,cxgb4i,libcxgbi.
Next two commits adds DDP support using
common iSCSI DDP Page Pod Manager.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common library module(libcxgb.ko) for
Chelsio drivers to remove duplicate code.
Code for iSCSI DDP Page Pod Manager is moved
from cxgb4.ko to libcxgb.ko. Earlier only cxgbit.ko
was using this code, now cxgb3i and cxgb4i will
also use common Page Pod manager code.
In future this module will have common connection
management and hardware specific code that can be
shared by multiple Chelsio drivers.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ageing_time type in br_set_ageing_time() from u32 to what it
is expected to be, i.e. a clock_t.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_stp_enable_bridge() does take the br->lock spinlock. Fix its wrongly
pasted comment and use the same as br_stp_disable_bridge().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using an IPoIB bond currently only active-backup mode is a valid
use case and this commit strengthens it.
Since commit 2ab82852a2 ("net/bonding: Enable bonding to enslave
netdevices not supporting set_mac_address()") was introduced till
4.7-rc1, IPoIB didn't support the set_mac_address ndo, and hence the
fail over mac policy always applied to IPoIB bonds.
With the introduction of commit 492a7e67ff ("IB/IPoIB: Allow setting
the device address"), that doesn't hold and practically IPoIB bonds are
broken as of that. To fix it, lets go to fail over mac if the device
doesn't support the ndo OR this is IPoIB device.
As a by-product, this commit also prevents a stack corruption which
occurred when trying to copy 20 bytes (IPoIB) device address
to a sockaddr struct that has only 16 bytes of storage.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: implement port mirroring offload
This patchset introduces tc matchall classifier and its offload
to Spectrum hardware. In combination with mirred action, defined port mirroring
setup is offloaded by mlxsw/spectrum driver.
The commands used for creating mirror ports:
tc qdisc add dev eth25 handle ffff: ingress
tc filter add dev eth25 parent ffff: \
matchall skip_sw \
action mirred egress mirror \
dev eth27
tc qdisc add dev eth25 handle 1: root prio
tc filter add dev eth25 parent 1: \
matchall skip_sw \
action mirred egress mirror \
dev eth27
These patches contain:
- Resource query implementation
- Hardware port mirorring support for spectrum.
- Definition of the matchall traffic classifier.
- General support for hw-offloading for that classifier.
- Specific spectrum implementaion for matchall offloading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch offloads port mirroring directives to hw using the matchall TC
with action mirror. It includes both the implementation of the
ndo_setup_tc function for the spectrum driver and the spectrum hardware
offload configuration code.
The hardware offload code is basically two new functions which are capable
of adding and removing a new mirror ports pair. It is done using the MPAT,
MPAR and SBIB registers:
- A new Switch-Port Analyzer (SPAN) entry is added using MPAT to the 'to'
port.
- The 'to' port is bound to the SPAN entry using MPAR register.
- In case of egress SPAN, the 'to' port gets a new internal shared
buffer using SBIB register.
In addition, a new database was added to the mlxsw_sp struct to store all
the SPAN entries and their bound ports list. The number of supported SPAN
entries is determined by resource query.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper function is_tcf_mirred_mirror helps finding whether an action
struct is of type mirred and is configured to be of type mirror.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPAR register is used to bind ports to a SPAN entry (which was
created using MPAT register) and thus mirror their traffic (ingress /
egress) to a different port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPAT register is used to query and configure the Switch Port Analyzer
(SPAN) table. This register is used to configure a port as a mirror output
port, while after that a mirrored input port can be bound using MPAR
register.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBIB register configures per port buffer for internal use. This
register is used to configure an egress mirror buffer on the egress port
which does the mirroring.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the work that have been done on offloading classifiers like u32
and flower, now the match-all classifier hw offloading is possible. if
the interface supports tc offloading.
To control the offloading, two tc flags have been introduced: skip_sw and
skip_hw. Typical usage:
tc filter add dev eth25 parent ffff: \
matchall skip_sw \
action mirred egress mirror \
dev eth27
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The matchall classifier matches every packet and allows the user to apply
actions on it. This filter is very useful in usecases where every packet
should be matched, for example, packet mirroring (SPAN) can be setup very
easily using that filter.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add max span resources to resources query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resources query implementation. If exists, query the HW for its
builtin resources instead of having them as consts in the code.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware in several ZTE devices (at least the MF823/831/910
modems/mifis) use OS fingerprinting to determine which type of device to
export. In addition, these devices export a REST API which can be used to
control the type of device. So far, on Linux, the devices have been seen as
RNDIS or CDC Ether.
When CDC Ether is used, devices of the same type are, as with RNDIS,
exported with the same, bogus random MAC address. In addition, the devices
(at least on all firmware revisions I have found) use the bogus MAC when
sending traffic routed from external networks. And as a final feature, the
devices sometimes export the link state incorrectly. There are also
references online to several other ZTE devices displaying this behavior,
with several different PIDs and MAC addresses.
This patch tries to improve the handling of ZTE devices by doing the
following:
* Create a new driver_info-struct that is used by ZTE devices that do not
have an explicit entry in the product table. This struct is the same as the
default cdc_ether driver info, but a new bind- and an rx_fixup-function
have been added.
* In the new bind function, we check if we have read a random MAC from the
device. If we have, then we generate a new random MAC address. This will
ensure that all devices get a unique MAC.
* The rx_fixup-function replaces the destination MAC address in the skb
with that of the device. I have not seen a revision of these devices that
behaves correctly (i.e., sets the right destination MAC), so I chose not to
do any comparison with for example the known, bogus addresses.
* The MF823/MF832/MF910 sometimes export cdc carrier on twice on connect
(the correct behavior is off then on). Work around this by manually setting
carrier to off if an on-notification is received and the NOCARRIER-bit is
not set.
This change will affect all devices, but it should take care of similar
mistakes made by other manufacturers. I tried to think of/look/test for
problems/regressions that could be introduced by this behavior, but could
not find any. However, my familiarity with this code path is not that
great, so there could be something I have overlooked.
I have tested this patch with multiple revisions of all three devices, and
they behave as expected. In other words, they all got a valid, random MAC,
the correct operational state and I can receive/sent traffic without
problems. I also tested with some other cdc_ether devices I have and did
not find any problems/regressions caused by the two general changes.
v3->v4:
* Forgot to remove unused variables, sorry about that (thanks David
Miller).
v2->v3:
* I had forgot to remove the random MAC generation from usbnet_cdc_bind()
(thanks Oliver).
* Rework logic in the ZTE bind-function a bit.
v1->v2:
* Only generate random MAC for ZTE devices (thanks Oliver Neukum).
* Set random MAC and do RX fixup for all ZTE devices that do not have a
product-entry, as the bogus MAC have been seen on devices with several
different PIDs/MAC addresses. In other words, it seems to be the default
behavior of ZTE CDC Ether devices (thanks Lars Melin).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
they are:
1) Count pre-established connections as active in "least connection"
schedulers such that pre-established connections to avoid overloading
backend servers on peak demands, from Michal Kubecek via Simon Horman.
2) Address a race condition when resizing the conntrack table by caching
the bucket size when fulling iterating over the hashtable in these
three possible scenarios: 1) dump via /proc/net/nf_conntrack,
2) unlinking userspace helper and 3) unlinking custom conntrack timeout.
From Liping Zhang.
3) Revisit early_drop() path to perform lockless traversal on conntrack
eviction under stress, use del_timer() as synchronization point to
avoid two CPUs evicting the same entry, from Florian Westphal.
4) Move NAT hlist_head to nf_conn object, this simplifies the existing
NAT extension and it doesn't increase size since recent patches to
align nf_conn, from Florian.
5) Use rhashtable for the by-source NAT hashtable, also from Florian.
6) Don't allow --physdev-is-out from OUTPUT chain, just like
--physdev-out is not either, from Hangbin Liu.
7) Automagically set on nf_conntrack counters if the user tries to
match ct bytes/packets from nftables, from Liping Zhang.
8) Remove possible_net_t fields in nf_tables set objects since we just
simply pass the net pointer to the backend set type implementations.
9) Fix possible off-by-one in h323, from Toby DiPasquale.
10) early_drop() may be called from ctnetlink patch, so we must hold
rcu read size lock from them too, this amends Florian's patch #3
coming in this batch, from Liping Zhang.
11) Use binary search to validate jump offset in x_tables, this
addresses the O(n!) validation that was introduced recently
resolve security issues with unpriviledge namespaces, from Florian.
12) Fix reference leak to connlabel in error path of nft_ct, from Zhang.
13) Three updates for nft_log: Fix log prefix leak in error path. Bail
out on loglevel larger than debug in nft_log and set on the new
NF_LOG_F_COPY_LEN flag when snaplen is specified. Again from Zhang.
14) Allow to filter rule dumps in nf_tables based on table and chain
names.
15) Simplify connlabel to always use 128 bits to store labels and
get rid of unused function in xt_connlabel, from Florian.
16) Replace set_expect_timeout() by mod_timer() from the h323 conntrack
helper, by Gao Feng.
17) Put back x_tables module reference in nft_compat on error, from
Liping Zhang.
18) Add a reference count to the x_tables extensions cache in
nft_compat, so we can remove them when unused and avoid a crash
if the extensions are rmmod, again from Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We "cache" the loaded match/target modules and reuse them, but when the
modules are removed, we still point to them. Then we may end up with
invalid memory references when using iptables-compat to add rules later.
Input the following commands will reproduce the kernel crash:
# iptables-compat -A INPUT -j LOG
# iptables-compat -D INPUT -j LOG
# rmmod xt_LOG
# iptables-compat -A INPUT -j LOG
BUG: unable to handle kernel paging request at ffffffffa05a9010
IP: [<ffffffff813f783e>] strcmp+0xe/0x30
Call Trace:
[<ffffffffa05acc43>] nft_target_select_ops+0x83/0x1f0 [nft_compat]
[<ffffffffa058a177>] nf_tables_expr_parse+0x147/0x1f0 [nf_tables]
[<ffffffffa058e541>] nf_tables_newrule+0x301/0x810 [nf_tables]
[<ffffffff8141ca00>] ? nla_parse+0x20/0x100
[<ffffffffa057fa8f>] nfnetlink_rcv+0x33f/0x53d [nfnetlink]
[<ffffffffa057f94b>] ? nfnetlink_rcv+0x1fb/0x53d [nfnetlink]
[<ffffffff817116b8>] netlink_unicast+0x178/0x220
[<ffffffff81711a5b>] netlink_sendmsg+0x2fb/0x3a0
[<ffffffff816b7fc8>] sock_sendmsg+0x38/0x50
[<ffffffff816b8a7e>] ___sys_sendmsg+0x28e/0x2a0
[<ffffffff816bcb7e>] ? release_sock+0x1e/0xb0
[<ffffffff81804ac5>] ? _raw_spin_unlock_bh+0x35/0x40
[<ffffffff816bcbe2>] ? release_sock+0x82/0xb0
[<ffffffff816b93d4>] __sys_sendmsg+0x54/0x90
[<ffffffff816b9422>] SyS_sendmsg+0x12/0x20
[<ffffffff81805172>] entry_SYSCALL_64_fastpath+0x1a/0xa9
So when nobody use the related match/target module, there's no need to
"cache" it. And nft_[match|target]_release are useless anymore, remove
them.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the user specify the invalid NFTA_MATCH_INFO/NFTA_TARGET_INFO attr
or memory alloc fail, we should call module_put to the related match
or target. Otherwise, we cannot remove the module even nobody use it.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simplify the code without any side effect. The set_expect_timeout is
used to modify the timer expired time. It tries to delete timer, and
add it again. So we could use mod_timer directly.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Fix memory leak in nftables, from Liping Zhang.
2) Need to check result of vlan_insert_tag() in batman-adv otherwise we
risk NULL skb derefs, from Sven Eckelmann.
3) Check for dev_alloc_skb() failures in cfg80211, from Gregory
Greenman.
4) Handle properly when we have ppp_unregister_channel() happening in
parallel with ppp_connect_channel(), from WANG Cong.
5) Fix DCCP deadlock, from Eric Dumazet.
6) Bail out properly in UDP if sk_filter() truncates the packet to be
smaller than even the space that the protocol headers need. From
Michal Kubecek.
7) Similarly for rose, dccp, and sctp, from Willem de Bruijn.
8) Make TCP challenge ACKs less predictable, from Eric Dumazet.
9) Fix infinite loop in bgmac_dma_tx_add() from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
packet: propagate sock_cmsg_send() error
net/mlx5e: Fix del vxlan port command buffer memset
packet: fix second argument of sock_tx_timestamp()
net: switchdev: change ageing_time type to clock_t
Update maintainer for EHEA driver.
net/mlx4_en: Add resilience in low memory systems
net/mlx4_en: Move filters cleanup to a proper location
sctp: load transport header after sk_filter
net/sched/sch_htb: clamp xstats tokens to fit into 32-bit int
net: cavium: liquidio: Avoid dma_unmap_single on uninitialized ndata
net: nb8800: Fix SKB leak in nb8800_receive()
et131x: Fix logical vs bitwise check in et131x_tx_timeout()
vlan: use a valid default mtu value for vlan over macsec
net: bgmac: Fix infinite loop in bgmac_dma_tx_add()
mlxsw: spectrum: Prevent invalid ingress buffer mapping
mlxsw: spectrum: Prevent overwrite of DCB capability fields
mlxsw: spectrum: Don't emit errors when PFC is disabled
mlxsw: spectrum: Indicate support for autonegotiation
mlxsw: spectrum: Force link training according to admin state
r8152: add MODULE_VERSION
...
Pull overlayfs fixes from Miklos Szeredi:
"This contains a fix for a potential crash/corruption issue and another
where the suid/sgid bits weren't cleared on write"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: verify upper dentry in ovl_remove_and_whiteout()
ovl: Copy up underlying inode's ->i_mode to overlay inode
ovl: handle ATTR_KILL*
Merge misc fixes from Andrew Morton:
"Five fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
pps: do not crash when failed to register
tools/vm/slabinfo: fix an unintentional printf
testing/radix-tree: fix a macro expansion bug
radix-tree: fix radix_tree_iter_retry() for tagged iterators.
mm: memcontrol: fix cgroup creation failure after many small jobs
Pull intel kabylake drm fixes from Dave Airlie:
"As mentioned Intel has gathered all the Kabylake fixes from -next,
which we've enabled in 4.7 for the first time, these are pretty much
limited in scope to only affects kabylake, which is hw that isn't
shipping yet. So I'm mostly okay with it going in now.
If we don't land this, it might be a good idea to disable kabylake
support in 4.7 before we ship"
* tag 'drm-fixes-for-v4.7-rc8-intel-kbl' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm/i915/kbl: Introduce the first official DMC for Kabylake.
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915/gen9: implement WaConextSwitchWithConcurrentTLBInvalidate
drm/i915/gen9: Add WaFbcHighMemBwCorruptionAvoidance
drm/i195/fbc: Add WaFbcNukeOnHostModify
drm/i915/gen9: Add WaFbcWakeMemOn
drm/i915/gen9: Add WaFbcTurnOffFbcWatermark
drm/i915/kbl: Add WaClearSlmSpaceAtContextSwitch
drm/i915/gen9: Add WaEnableChickenDCPR
drm/i915/kbl: Add WaDisableSbeCacheDispatchPortSharing
drm/i915/kbl: Add WaDisableGafsUnitClkGating
drm/i915/kbl: Add WaForGAMHang
drm/i915: Add WaInsertDummyPushConstP for bxt and kbl
drm/i915/kbl: Add WaDisableDynamicCreditSharing
drm/i915/kbl: Add WaDisableGamClockGating
drm/i915/gen9: Enable must set chicken bits in config0 reg
drm/i915/kbl: Add WaDisableLSQCROPERFforOCL
drm/i915/kbl: Add WaDisableSDEUnitClockGating
drm/i915/kbl: Add WaDisableFenceDestinationToSLM for A0
drm/i915/kbl: Add WaEnableGapsTsvCreditFix
...
Pull drm fixes from Dave Airlie:
"Two i915 regression fixes.
Intel have submitted some Kabylake fixes I'll send separately, since
this is the first kernel with kabylake support and they don't go much
outside that area I think they should be fine"
* tag 'drm-fixes-for-v4.7-rc8-intel' of git://people.freedesktop.org/~airlied/linux:
drm/i915: add missing condition for committing planes on crtc
drm/i915: Treat eDP as always connected, again
A handful of fixes before final release:
Marvell Armada:
- One to fix a typo in the devicetree specifying memory ranges for the
crypto engine
- Two to deal with marking PCI and device-memory as strongly ordered to
avoid hardware deadlocks, in particular when enabling above crypto driver.
- Compile fix for PM
Allwinner:
- DT clock fixes to deal with u-boot-enabled framebuffer (simplefb).
- Make R8 (C.H.I.P. SoC) inherit system compatibility from A13 to
make clocks register proper.
Tegra:
- Fix SD card voltage setting on the Tegra3 Beaver dev board
Misc:
- Two maintainers updates for STM32 and STi platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QMwv
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes before final release:
Marvell Armada:
- One to fix a typo in the devicetree specifying memory ranges for
the crypto engine
- Two to deal with marking PCI and device-memory as strongly ordered
to avoid hardware deadlocks, in particular when enabling above
crypto driver.
- Compile fix for PM
Allwinner:
- DT clock fixes to deal with u-boot-enabled framebuffer (simplefb).
- Make R8 (C.H.I.P. SoC) inherit system compatibility from A13 to
make clocks register proper.
Tegra:
- Fix SD card voltage setting on the Tegra3 Beaver dev board
Misc:
- Two maintainers updates for STM32 and STi platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: beaver: Allow SD card voltage to be changed
MAINTAINERS: update STi maintainer list
MAINTAINERS: update STM32 maintainers list
ARM: mvebu: compile pm code conditionally
ARM: dts: sun7i: Fix pll3x2 and pll7x2 not having a parent clock
ARM: dts: sunxi: Add pll3 to simplefb nodes clocks lists
ARM: dts: armada-38x: fix MBUS_ID for crypto SRAM on Armada 385 Linksys
ARM: mvebu: map PCI I/O regions strongly ordered
ARM: mvebu: fix HW I/O coherency related deadlocks
ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13
Pull crypto fixes from Herbert Xu:
"This fixes a sporadic build failure in the qat driver as well as a
memory corruption bug in rsa-pkcs1pad"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: rsa-pkcs1pad - fix rsa-pkcs1pad request struct
crypto: qat - make qat_asym_algs.o depend on asn1 headers
Pull key handling fixes from James Morris:
"Quoting David Howells:
Here are three miscellaneous fixes:
(1) Fix a panic in some debugging code in PKCS#7. This can only
happen by explicitly inserting a #define DEBUG into the code.
(2) Fix the calculation of the digest length in the PE file parser.
This causes a failure where there should be a success.
(3) Fix the case where an X.509 cert can be added as an asymmetric key
to a trusted keyring with no trust restriction if no AKID is
supplied.
Bugs (1) and (2) aren't particularly problematic, but (3) allows a
security check to be bypassed. Happily, this is a recent regression
and never made it into a released kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: Fix for erroneous trust of incorrectly signed X.509 certs
pefile: Fix the failure of calculation for digest
PKCS#7: Fix panic when referring to the empty AKID when DEBUG defined
Pull input fixes from Dmitry Torokhov:
"A few more fixes for the input subsystem:
- restore naming for tsc2005 touchscreens as some userspace match on it
- fix out of bound access in legacy keyboard driver
- fixup in RMI4 driver
Everything is tagged for stable as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc200x - report proper input_dev name
tty/vt/keyboard: fix OOB access in do_compute_shiftstate()
Input: synaptics-rmi4 - fix maximum size check for F12 control register 8
Pull libnvdimm fix from Dan Williams:
"This contains a regression fix for a problem that was introduced in
v4.7-rc6.
In 4.7-rc1 we introduced auto-probing for the ACPI DSM (device-
specific-method) format that the platform firmware implements for
nvdimm devices. We initially fixed a regression in probing the QEMU
DSM implementation by making acpi_check_dsm() tolerant of the way QEMU
reports the "0 DSMs supported" condition.
However, that broke HPE platforms since that tolerance caused the
driver to mistakenly match the 1-zero-byte response those platforms
give to "unknown" commands. Instead, we simply make the driver
tolerant of not finding any supported DSMs. This has been tested to
work with both QEMU and HPE platforms.
This commit has appeared in a -next release with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: make DIMM DSMs optional
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xQOQ
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"Compile problem fix for Tegra,
Sorry to send this in the last minute but Ingo says this build failure
is very prominent so I'm not going to wait for v4.7 before sending it.
It is a case of COMPILE_TEST causing more problems than it solves and
I'm already swearing about me shooting myself in the foot with that
gun :("
* tag 'gpio-v4.7-6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra: don't auto-enable for COMPILE_TEST
drivers, and one bug in a sunxi clk driver introduced in the 4.7 merge
window.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJXkWveAAoJEAQCK3UHF29dSL0H/RL3maAwq4Ik5Wla6+AmpZ31
YOy5yXUp6y9ZAEjRhZfp5pzEaDk1A0q3Yy1QsN1xjyGgDo67xc4yPgB0ZQZJ58TU
ZqUPMe2gHIXz++fcWHMKm6gbVcs7L5tdYsYAbEYgkzQqm4gY0IyWvERYgDlmnjpI
R/SsgKKhrNfRwxQEB5Er9nx0lyq2kQ/8ocOgGJjDoeCWbdMczO6MWYIPSAYsQjct
wJGXhvYFKYLefD1LxynjonEnJQeimk6MGEeKsZ6hqVva/oHuw0qtOIRodyWJ4sSU
xiEitnLK1109fRfe84aKIpDw8mf2RjZludgTWNhDk3VpZzkpV4pxPESHfiACWYQ=
=T8Je
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"Fix a bug in the at91 clk driver, two compile time warnings in sunxi
clk drivers, and one bug in a sunxi clk driver introduced in the 4.7
merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: fix clk_programmable_set_parent()
clk: sunxi: remove unused variable
clk: sunxi: display: Add per-clock flags
clk: sunxi: tcon-ch1: Do not return a negative error in get_parent
Pull libata fix from Tejun Heo:
"Another fallout from max_sectors bump a couple years ago. The lite-on
optical drive times out on large requests"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: LITE-ON CX1-JB256-HP needs lower max_sectors
Now one more regression fix in addition to the previous pull request:
two changes in the core part are for unusual error paths, while the
rest are the regular HD-audio fixes and one USB-audio regression fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ky73
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No surprise, just a few small fixes: a couple of changes are seen in
the core part, and both of them are rather for unusual error paths.
The rest are the regular HD-audio fixes and one USB-audio regression
fix"
* tag 'sound-4.7-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix quirks code is not called
ALSA: hda: add AMD Stoney PCI ID with proper driver caps
ALSA: hda - fix use-after-free after module unload
ALSA: pcm: Free chmap at PCM free callback, too
ALSA: ctl: Stop notification after disconnection
ALSA: hda/realtek - add new pin definition in alc225 pin quirk table
Pull NVMe fix from Jens Axboe:
"Late addition here, it's basically a revert of a patch that was added
in this merge window, but has proven to cause problems.
This is swapping out the RCU based namespace protection with a good
old mutex instead"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: Remove RCU namespace protection
With this command sequence:
modprobe plip
modprobe pps_parport
rmmod pps_parport
the partport_pps modules causes this crash:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: parport_detach+0x1d/0x60 [pps_parport]
Oops: 0000 [#1] SMP
...
Call Trace:
parport_unregister_driver+0x65/0xc0 [parport]
SyS_delete_module+0x187/0x210
The sequence that builds up to this is:
1) plip is loaded and takes the parport device for exclusive use:
plip0: Parallel port at 0x378, using IRQ 7.
2) pps_parport then fails to grab the device:
pps_parport: parallel port PPS client
parport0: cannot grant exclusive access for device pps_parport
pps_parport: couldn't register with parport0
3) rmmod of pps_parport is then killed because it tries to access
pardev->name, but pardev (taken from port->cad) is NULL.
So add a check for NULL in the test there too.
Link: http://lkml.kernel.org/r/20160714115245.12651-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The curly braces are missing here so we print stuff unintentionally.
Fixes: 9da4714a2d ('slub: slabinfo update for cmpxchg handling')
Link: http://lkml.kernel.org/r/20160715211243.GE19522@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no parentheses around this macro and it causes a problem when
we do:
index = rand() % THRASH_SIZE;
Link: http://lkml.kernel.org/r/20160715210953.GC19522@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
radix_tree_iter_retry() resets slot to NULL, but it doesn't reset tags.
Then NULL slot and non-zero iter.tags passed to radix_tree_next_slot()
leading to crash:
RIP: radix_tree_next_slot include/linux/radix-tree.h:473
find_get_pages_tag+0x334/0x930 mm/filemap.c:1452
....
Call Trace:
pagevec_lookup_tag+0x3a/0x80 mm/swap.c:960
mpage_prepare_extent_to_map+0x321/0xa90 fs/ext4/inode.c:2516
ext4_writepages+0x10be/0x2b20 fs/ext4/inode.c:2736
do_writepages+0x97/0x100 mm/page-writeback.c:2364
__filemap_fdatawrite_range+0x248/0x2e0 mm/filemap.c:300
filemap_write_and_wait_range+0x121/0x1b0 mm/filemap.c:490
ext4_sync_file+0x34d/0xdb0 fs/ext4/fsync.c:115
vfs_fsync_range+0x10a/0x250 fs/sync.c:195
vfs_fsync fs/sync.c:209
do_fsync+0x42/0x70 fs/sync.c:219
SYSC_fdatasync fs/sync.c:232
SyS_fdatasync+0x19/0x20 fs/sync.c:230
entry_SYSCALL_64_fastpath+0x23/0xc1 arch/x86/entry/entry_64.S:207
We must reset iterator's tags to bail out from radix_tree_next_slot()
and go to the slow-path in radix_tree_next_chunk().
Fixes: 46437f9a55 ("radix-tree: fix race in gang lookup")
Link: http://lkml.kernel.org/r/1468495196-10604-1-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memory controller has quite a bit of state that usually outlives the
cgroup and pins its CSS until said state disappears. At the same time
it imposes a 16-bit limit on the CSS ID space to economically store IDs
in the wild. Consequently, when we use cgroups to contain frequent but
small and short-lived jobs that leave behind some page cache, we quickly
run into the 64k limitations of outstanding CSSs. Creating a new cgroup
fails with -ENOSPC while there are only a few, or even no user-visible
cgroups in existence.
Although pinning CSSs past cgroup removal is common, there are only two
instances that actually need an ID after a cgroup is deleted: cache
shadow entries and swapout records.
Cache shadow entries reference the ID weakly and can deal with the CSS
having disappeared when it's looked up later. They pose no hurdle.
Swap-out records do need to pin the css to hierarchically attribute
swapins after the cgroup has been deleted; though the only pages that
remain swapped out after offlining are tmpfs/shmem pages. And those
references are under the user's control, so they are manageable.
This patch introduces a private 16-bit memcg ID and switches swap and
cache shadow entries over to using that. This ID can then be recycled
after offlining when the CSS remains pinned only by objects that don't
specifically need it.
This script demonstrates the problem by faulting one cache page in a new
cgroup and deleting it again:
set -e
mkdir -p pages
for x in `seq 128000`; do
[ $((x % 1000)) -eq 0 ] && echo $x
mkdir /cgroup/foo
echo $$ >/cgroup/foo/cgroup.procs
echo trex >pages/$x
echo $$ >/cgroup/cgroup.procs
rmdir /cgroup/foo
done
When run on an unpatched kernel, we eventually run out of possible IDs
even though there are no visible cgroups:
[root@ham ~]# ./cssidstress.sh
[...]
65000
mkdir: cannot create directory '/cgroup/foo': No space left on device
After this patch, the IDs get released upon cgroup destruction and the
cache and css objects get released once memory reclaim kicks in.
[hannes@cmpxchg.org: init the IDR]
Link: http://lkml.kernel.org/r/20160621154601.GA22431@cmpxchg.org
Fixes: b2052564e6 ("mm: memcontrol: continue cache reclaim from offlined groups")
Link: http://lkml.kernel.org/r/20160617162516.GD19084@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: John Garcia <john.garcia@mesosphere.io>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Nikolay Borisov <kernel@kyup.com>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conntrack label extension is currently variable-sized, e.g. if
only 2 labels are used by iptables rules then the labels->bits[] array
will only contain one element.
We track size of each label storage area in the 'words' member.
But in nftables and openvswitch we always have to ask for worst-case
since we don't know what bit will be used at configuration time.
As most arches are 64bit we need to allocate 24 bytes in this case:
struct nf_conn_labels {
u8 words; /* 0 1 */
/* XXX 7 bytes hole, try to pack */
long unsigned bits[2]; /* 8 24 */
Make bits a fixed size and drop the words member, it simplifies
the code and only increases memory requirements on x86 when
less than 64bit labels are required.
We still only allocate the extension if its needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I stumbled over a build error with COMPILE_TEST and CONFIG_OF
disabled:
drivers/gpio/gpio-tegra.c: In function 'tegra_gpio_probe':
drivers/gpio/gpio-tegra.c:603:9: error: 'struct gpio_chip' has no member named 'of_node'
The problem is that the newly added GPIO_TEGRA Kconfig symbol
does not have a dependency on CONFIG_OF. However, there is another
problem here as the driver gets enabled unconditionally whenever
COMPILE_TEST is set.
This fixes both problems, by making the symbol user-visible
when COMPILE_TEST is set and default-enabled for ARCH_TEGRA=y.
As a side-effect, it is now possible to compile-test a Tegra
kernel with GPIO support disabled, which is harmless.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4dd4dd1d21 ("gpio: tegra: Allow compile test")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow for child request context the struct akcipher_request child_req
needs to be at the end of the structure.
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The upper dentry may become stale before we call ovl_lock_rename_workdir.
For example, someone could (mistakenly or maliciously) manually unlink(2)
it directly from upperdir.
To ensure it is not stale, let's lookup it after ovl_lock_rename_workdir
and and check if it matches the upper dentry.
Essentially, it is the same problem and similar solution as in
commit 11f3710417 ("ovl: verify upper dentry before unlink and rename").
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org>
sock_cmsg_send() can return different error codes and not only
-EINVAL, and we should properly propagate them.
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
