In the case of CHECKSUM_COMPLETE the skb checksum should be updated in
{push,pop}_mpls() as they the type in the ethernet header.
As suggested by Pravin Shelar.
Cc: Pravin Shelar <pshelar@nicira.com>
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to kernel")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
When using conntrack helpers from OVS, a common configuration is to
perform a lookup without specifying a helper, then go through a
firewalling policy, only to decide to attach a helper afterwards.
In this case, the initial lookup will cause a ct entry to be attached to
the skb, then the later commit with helper should attach the helper and
confirm the connection. However, the helper attachment has been missing.
If the user has enabled automatic helper attachment, then this issue
will be masked as it will be applied in init_conntrack(). It is also
masked if the action is executed from ovs_packet_cmd_execute() as that
will construct a fresh skb.
This patch fixes the issue by making an explicit call to try to assign
the helper if there is a discrepancy between the action's helper and the
current skb->nfct.
Fixes: cae3a26275 ("openvswitch: Allow attaching helpers to ct action")
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a900689264 ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the protocol is not natively supported, this assigns generic protocol
tracker so we can always assume a valid pointer after these calls.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Joe Stringer <joe@ovn.org>
I also fix commit 8b32ab9e6ef1: use nla_total_size_64bit() for
OVS_FLOW_ATTR_USED in ovs_flow_cmd_msg_size().
Fixes: 8b32ab9e6ef1 ("ovs: use nla_put_u64_64bit()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, mostly from Florian Westphal to sort out the lack of sufficient
validation in x_tables and connlabel preparation patches to add
nf_tables support. They are:
1) Ensure we don't go over the ruleset blob boundaries in
mark_source_chains().
2) Validate that target jumps land on an existing xt_entry. This extra
sanitization comes with a performance penalty when loading the ruleset.
3) Introduce xt_check_entry_offsets() and use it from {arp,ip,ip6}tables.
4) Get rid of the smallish check_entry() functions in {arp,ip,ip6}tables.
5) Make sure the minimal possible target size in x_tables.
6) Similar to #3, add xt_compat_check_entry_offsets() for compat code.
7) Check that standard target size is valid.
8) More sanitization to ensure that the target_offset field is correct.
9) Add xt_check_entry_match() to validate that matches are well-formed.
10-12) Three patch to reduce the number of parameters in
translate_compat_table() for {arp,ip,ip6}tables by using a container
structure.
13) No need to return value from xt_compat_match_from_user(), so make
it void.
14) Consolidate translate_table() so it can be used by compat code too.
15) Remove obsolete check for compat code, so we keep consistent with
what was already removed in the native layout code (back in 2007).
16) Get rid of target jump validation from mark_source_chains(),
obsoleted by #2.
17) Introduce xt_copy_counters_from_user() to consolidate counter
copying, and use it from {arp,ip,ip6}tables.
18,22) Get rid of unnecessary explicit inlining in ctnetlink for dump
functions.
19) Move nf_connlabel_match() to xt_connlabel.
20) Skip event notification if connlabel did not change.
21) Update of nf_connlabels_get() to make the upcoming nft connlabel
support easier.
23) Remove spinlock to read protocol state field in conntrack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_data() is now aligned on a 64-bit area.
A temporary version (nla_put_be64_32bit()) is added for nla_put_net64().
This function is removed in the next patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
When using masked actions the ipv6_proto field of an action
to set IPv6 fields may be zero rather than the prevailing protocol
which will result in skipping checksum recalculation.
This patch resolves the problem by relying on the protocol
in the flow key rather than that in the set field action.
Fixes: 83d2b9ba1a ("net: openvswitch: Support masked set actions.")
Cc: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_connlabel_set() takes the bit number that we would like to set.
nf_connlabels_get() however took the number of bits that we want to
support.
So e.g. nf_connlabels_get(32) support bits 0 to 31, but not 32.
This changes nf_connlabels_get() to take the highest bit that we want
to set.
Callers then don't have to cope with a potential integer wrap
when using nf_connlabels_get(bit + 1) anymore.
Current callers are fine, this change is only to make folloup
nft ct label set support simpler.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for you net tree,
they are:
1) There was a race condition between parallel save/swap and delete,
which resulted a kernel crash due to the increase ref for save, swap,
wrong ref decrease operations. Reported and fixed by Vishwanath Pai.
2) OVS should call into CT NAT for packets of new expected connections only
when the conntrack state is persisted with the 'commit' option to the
OVS CT action. From Jarno Rajahalme.
3) Resolve kconfig dependencies with new OVS NAT support. From Arnd Bergmann.
4) Early validation of entry->target_offset to make sure it doesn't take us
out from the blob, from Florian Westphal.
5) Again early validation of entry->next_offset to make sure it doesn't take
out from the blob, also from Florian.
6) Check that entry->target_offset is always of of sizeof(struct xt_entry)
for unconditional entries, when checking both from check_underflow()
and when checking for loops in mark_source_chains(), again from
Florian.
7) Fix inconsistent behaviour in nfnetlink_queue when
NFQA_CFG_F_FAIL_OPEN is set and netlink_unicast() fails due to buffer
overrun, we have to reinject the packet as the user expects.
8) Enforce nul-terminated table names from getsockopt GET_ENTRIES
requests.
9) Don't assume skb->sk is set from nft_bridge_reject and synproxy,
this fixes a recent update of the code to namespaceify
ip_default_ttl, patch from Liping Zhang.
This batch comes with four patches to validate x_tables blobs coming
from userspace. CONFIG_USERNS exposes the x_tables interface to
unpriviledged users and to be honest this interface never received the
attention for this move away from the CAP_NET_ADMIN domain. Florian is
working on another round with more patches with more sanity checks, so
expect a bit more Netfilter fixes in this development cycle than usual.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The openvswitch code has gained support for calling into the
nf-nat-ipv4/ipv6 modules, however those can be loadable modules
in a configuration in which openvswitch is built-in, leading
to link errors:
net/built-in.o: In function `__ovs_ct_lookup':
:(.text+0x2cc2c8): undefined reference to `nf_nat_icmp_reply_translation'
:(.text+0x2cc66c): undefined reference to `nf_nat_icmpv6_reply_translation'
The dependency on (!NF_NAT || NF_NAT) prevents similar issues,
but NF_NAT is set to 'y' if any of the symbols selecting
it are built-in, but the link error happens when any of them
are modular.
A second issue is that even if CONFIG_NF_NAT_IPV6 is built-in,
CONFIG_NF_NAT_IPV4 might be completely disabled. This is unlikely
to be useful in practice, but the driver currently only handles
IPv6 being optional.
This patch improves the Kconfig dependency so that openvswitch
cannot be built-in if either of the two other symbols are set
to 'm', and it replaces the incorrect #ifdef in ovs_ct_nat_execute()
with two "if (IS_ENABLED())" checks that should catch all corner
cases also make the code more readable.
The same #ifdef exists ovs_ct_nat_to_attr(), where it does not
cause a link error, but for consistency I'm changing it the same
way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 05752523e5 ("openvswitch: Interface with NAT.")
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
OVS should call into CT NAT for packets of new expected connections only
when the conntrack state is persisted with the 'commit' option to the
OVS CT action. The test for this condition is doubly wrong, as the CT
status field is ANDed with the bit number (IPS_EXPECTED_BIT) rather
than the mask (IPS_EXPECTED), and due to the wrong assumption that the
expected bit would apply only for the first (i.e., 'new') packet of a
connection, while in fact the expected bit remains on for the lifetime of
an expected connection. The 'ctinfo' value IP_CT_RELATED derived from
the ct status can be used instead, as it is only ever applicable to
the 'new' packets of the expected connection.
Fixes: 05752523e5 ('openvswitch: Interface with NAT.')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For the input parameter count, it's better to use the size
of destination buffer size, as nla_memcpy would take into
account the length of the source netlink attribute when
a data is copied from an attribute.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
eBPF defines this as BPF_TUNLEN_MAX and OVS just uses the hard-coded
value inside struct sw_flow_key. Thus, add and use IP_TUNNEL_OPTS_MAX
for this, which makes the code a bit more generic and allows to remove
BPF_TUNLEN_MAX from eBPF code.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently output of MPLS packets on tunnel vports is not allowed by Open
vSwitch. This is because historically encapsulation was done in such a way
that the inner_protocol field of the skb needed to hold the inner protocol
for both MPLS and tunnel encapsulation in order for GSO segmentation to be
performed correctly.
Since b2acd1dc39 ("openvswitch: Use regular GRE net_device instead of
vport") Open vSwitch makes use of lwt to output to tunnel netdevs which
perform encapsulation. As no drivers expose support for MPLS offloads this
means that GSO packets are segmented in software by validate_xmit_skb(),
which is called from __dev_queue_xmit(), before tunnel encapsulation occurs.
This means that the inner protocol of MPLS is no longer needed by the time
encapsulation occurs and the contention on the inner_protocol field of the
skb no longer occurs.
Thus it is now safe to output MPLS to tunnel vports.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
Pablo Neira Ayuso says:
====================
Netfilter/IPVS/OVS updates for net-next
The following patchset contains Netfilter/IPVS fixes and OVS NAT
support, more specifically this batch is composed of:
1) Fix a crash in ipset when performing a parallel flush/dump with
set:list type, from Jozsef Kadlecsik.
2) Make sure NFACCT_FILTER_* netlink attributes are in place before
accessing them, from Phil Turnbull.
3) Check return error code from ip_vs_fill_iph_skb_off() in IPVS SIP
helper, from Arnd Bergmann.
4) Add workaround to IPVS to reschedule existing connections to new
destination server by dropping the packet and wait for retransmission
of TCP syn packet, from Julian Anastasov.
5) Allow connection rescheduling in IPVS when in CLOSE state, also
from Julian.
6) Fix wrong offset of SIP Call-ID in IPVS helper, from Marco Angaroni.
7) Validate IPSET_ATTR_ETHER netlink attribute length, from Jozsef.
8) Check match/targetinfo netlink attribute size in nft_compat,
patch from Florian Westphal.
9) Check for integer overflow on 32-bit systems in x_tables, from
Florian Westphal.
Several patches from Jarno Rajahalme to prepare the introduction of
NAT support to OVS based on the Netfilter infrastructure:
10) Schedule IP_CT_NEW_REPLY definition for removal in
nf_conntrack_common.h.
11) Simplify checksumming recalculation in nf_nat.
12) Add comments to the openvswitch conntrack code, from Jarno.
13) Update the CT state key only after successful nf_conntrack_in()
invocation.
14) Find existing conntrack entry after upcall.
15) Handle NF_REPEAT case due to templates in nf_conntrack_in().
16) Call the conntrack helper functions once the conntrack has been
confirmed.
17) And finally, add the NAT interface to OVS.
The batch closes with:
18) Cleanup to use spin_unlock_wait() instead of
spin_lock()/spin_unlock(), from Nicholas Mc Guire.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend OVS conntrack interface to cover NAT. New nested
OVS_CT_ATTR_NAT attribute may be used to include NAT with a CT action.
A bare OVS_CT_ATTR_NAT only mangles existing and expected connections.
If OVS_NAT_ATTR_SRC or OVS_NAT_ATTR_DST is included within the nested
attributes, new (non-committed/non-confirmed) connections are mangled
according to the rest of the nested attributes.
The corresponding OVS userspace patch series includes test cases (in
tests/system-traffic.at) that also serve as example uses.
This work extends on a branch by Thomas Graf at
https://github.com/tgraf/ovs/tree/nat.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is no need to help connections that are not confirmed, so we can
delay helping new connections to the time when they are confirmed.
This change is needed for NAT support, and having this as a separate
patch will make the following NAT patch a bit easier to review.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Repeat the nf_conntrack_in() call when it returns NF_REPEAT. This
avoids dropping a SYN packet re-opening an existing TCP connection.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a new function ovs_ct_find_existing() to find an existing
conntrack entry for which this packet was already applied to. This is
only to be called when there is evidence that the packet was already
tracked and committed, but we lost the ct reference due to an
userspace upcall.
ovs_ct_find_existing() is called from skb_nfct_cached(), which can now
hide the fact that the ct reference may have been lost due to an
upcall. This allows ovs_ct_commit() to be simplified.
This patch is needed by later "openvswitch: Interface with NAT" patch,
as we need to be able to pass the packet through NAT using the
original ct reference also after the reference is lost after an
upcall.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Only a successful nf_conntrack_in() call can effect a connection state
change, so it suffices to update the key only after the
nf_conntrack_in() returns.
This change is needed for the later NAT patches.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes the code easier to understand and the following patches
more focused.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Remove the definition of IP_CT_NEW_REPLY from the kernel as it does
not make sense. This allows the definition of IP_CT_NUMBER to be
simplified as well.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we want to change a flow using netlink, we have to identify it to
be able to perform a lookup. Both the flow key and unique flow ID
(ufid) are valid identifiers, but we always have to specify the flow
key in the netlink message. When both attributes are there, the ufid
is used. The flow key is used to validate the actions provided by
the userland.
This commit allows to use the ufid without having to provide the flow
key, as it is already done in the netlink 'flow get' and 'flow del'
path. The flow key remains mandatory when an action is provided.
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements bookkeeping support to compute the maximum
headroom for all the devices in each datapath. When said value
changes, the underlying devs are notified via the
ndo_set_rx_headroom method.
This also increases the internal vports xmit performance.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace individual implementations with the recently introduced
skb_postpush_rcsum() helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Tom Herbert <tom@herbertland.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
the commit 35e2d1152b ("tunnels: Allow IPv6 UDP checksums to be
correctly controlled.") changed the default xmit checksum setting
for lwt vxlan/geneve ipv6 tunnels, so that now the checksum is not
set into external UDP header.
This commit changes the rx checksum setting for both lwt vxlan/geneve
devices created by openvswitch accordingly, so that lwt over ipv6
tunnel pairs are again able to communicate with default values.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bb9b18fb55 ("genl: Add genlmsg_new_unicast() for
unicast message allocation")'.
Nothing wrong with it; its no longer needed since this was only for
mmapped netlink support.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit 795449d8b8 ("openvswitch: Enable memory mapped Netlink i/o").
Following the mmaped netlink removal this code can be removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length
below MTU this give about 2% performance increase
when tunneling over ipv4 and about 60% when tunneling
over ipv6
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typos found in printk and Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Operations with the GENL_ADMIN_PERM flag fail permissions checks because
this flag means we call netlink_capable, which uses the init user ns.
Instead, let's introduce a new flag, GENL_UNS_ADMIN_PERM for operations
which should be allowed inside a user namespace.
The motivation for this is to be able to run openvswitch in unprivileged
containers. I've tested this and it seems to work, but I really have no
idea about the security consequences of this patch, so thoughts would be
much appreciated.
v2: use the GENL_UNS_ADMIN_PERM flag instead of a check in each function
v3: use separate ifs for UNS_ADMIN_PERM and ADMIN_PERM, instead of one
massive one
Reported-by: James Page <james.page@canonical.com>
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com>
CC: Eric Biederman <ebiederm@xmission.com>
CC: Pravin Shelar <pshelar@ovn.org>
CC: Justin Pettit <jpettit@nicira.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was seen that defective configurations of openvswitch could overwrite
the STACK_END_MAGIC and cause a hard crash of the kernel because of too
many recursions within ovs.
This problem arises due to the high stack usage of openvswitch. The rest
of the kernel is fine with the current limit of 10 (RECURSION_LIMIT).
We use the already existing recursion counter in ovs_execute_actions to
implement an upper bound of 5 recursions.
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skb_gso_segment() uses skb control block during segmentation.
This patch adds 32-bytes room for previous control block which
will be copied into all resulting segments.
This patch fixes kernel crash during fragmenting forwarded packets.
Fragmentation requires valid IP CB in skb for clearing ip options.
Also patch removes custom save/restore in ovs code, now it's redundant.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiP-0MZ-FExV2HutTvE9U-QQtkKSoE--KN=JQE5STYsjAA@mail.gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
commit be4ace6e6b ("openvswitch: Move dev pointer into vport itself")
The commit above added @dev and moved @rcu to the bottom of struct
vport, but the change was not reflected in the kernel doc. So let's
update the kernel doc as well.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6b001e682e ("openvswitch: Use Geneve device.")
The commit above introduced 'port_no' as the name for the member of
struct geneve_port. The correct name should be 'dst_port' as described
in the kernel doc. Let's fix that member name and all the pertinent
instances so that both doc and code would be consistent.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6b001e682e ("openvswitch: Use Geneve device.")
The commit above deleted the only call site of ovs_tunnel_route_lookup()
and now that function is not used any more. So let's delete the function
definition as well.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b48bb8506c5 ("openvswitch: Fix helper reference leak") fixed a
reference leak on helper objects, but inadvertently introduced a leak on
the ct template.
Previously, ct_info.ct->general.use was initialized to 0 by
nf_ct_tmpl_alloc() and only incremented when ovs_ct_copy_action()
returned successful. If an error occurred while adding the helper or
adding the action to the actions buffer, the __ovs_ct_free_action()
cleanup would use nf_ct_put() to free the entry; However, this relies on
atomic_dec_and_test(ct_info.ct->general.use). This reference must be
incremented first, or nf_ct_put() will never free it.
Fix the issue by acquiring a reference to the template immediately after
allocation.
Fixes: cae3a26275 ("openvswitch: Allow attaching helpers to ct action")
Fixes: 5b48bb8506c5 ("openvswitch: Fix helper reference leak")
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a set action tunnel attributes should be encoded in a
nested action.
I noticed this because ovs-dpctl was reporting an error
when dumping flows due to the incorrect encoding of tunnel attributes
in a set action.
Fixes: fc4099f172 ("openvswitch: Fix egress tunnel info.")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
