Allows interrupts to occur on the sbc834x. Currently PCI devices
get assigned an incorrect IRQ and so the interrupt count never
increases. This was tested with the 82546GB based dual port E1000
PCI-X NIC which uses two distinct IRQ lines on the one card.
root@localhost:/root> cat /proc/interrupts | grep eth
17: 78 IPIC Level eth1
48: 27121 IPIC Level eth0
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x
local bus, so add a localbus node in DTS with MTD partitions.
The recent U-boot commit fe613cdd4eb moves u-boot to the beginning
of flash, hence the legacy label on the partition at the end of flash.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since only one of the SoC USB devices is brought out to a physical
connector on the board, remove the 2nd (USB-DR) node from the DTS.
Having it present and USB enabled will cause a hang at boot.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
gcc v4.4 currently produces this build warning:
arch/powerpc/boot/mktree.c: In function 'main':
arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules
tmpbuf is only used as an array of unsigned ints, so declare it that way.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update GE Fanuc DTS to match the alterations suggested during the merge of
the ppc9a DTS in commit 740d36ae63
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables the XMC (PCIe daughter card) site on the SBC310.
STG enter the description for the patch above.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Actually, the support is already there, but it requires newer U-Boots
(to fill-in clock-frequency, and setup pin multiplexing).
Though, it appears that on RDB boards USBB pins aren't multiplexed
between USB and eSDHC (unlike MDS boards, where USB and eSDHC share
pctl and pwrfault pins).
So, for RDB boards we can safely setup pinmux and manually fill-in
clock-frequency, thus making eSDHC work even with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch simply adds four eeprom nodes to MPC8548CDS' device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- add I2C support
- add FCC1 and FCC2 support
- fix bogus gpio numbering in plattform code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Added a device tree that should be similiar to mpc8536ds.dtb except
the physical addresses for all IO are above the 4G boundary.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8536ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the following devices to the Kilauea dts:
- PPC4xx NAND controller (NDFC)
- I2C RTC (Dallas DS1338)
- I2C HWMON (Dallas DS1775)
Additionally the partitioning of the NOR FLASH is changed. The dtb
partition has been missing. Fixed in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also some whitespace cleanup in the USB device nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dtc was moved in 9fffb55f66 from
arch/powerpc/boot/ to scripts/dtc/
This patch updates the wrapper script to point to the new location of dtc.
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.
8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [00000900] 0x900
LR [c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c
[cf831e40] [c0235250] pci_call_probe+0x20/0x30
[...]
This patch fixes the issue by specifying the correct PCI IO base
address.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:
fsl-pq_mdio: probe of e0082120.mdio failed with error -16
And obviously ethernet doesn't work after this.
This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GPIO LEDS driver now has a default state of "keep". Update the Warp DTS
and platform file to take advantage of this new state. This removes the
hardcoding of the two LEDs on the Warp.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The kernel reserves the I/O address space from 0x0 to 0xfff for legacy
ISA devices. Change the ranges property for the PCI2ISA bridge to match
the kernels behavior, even if the ranges property isn't used for now.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Have git ignore generated files from dtc compile
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For yet unknown reason 4-bit mode doesn't work on MPC8569E-MDS boards,
so make 1-bit mode default. When we resolve the issue, u-boot will
remove sdhci,1-bit-only property from the device tree, while SDHCI
will still work with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node for the i2c eeprom and delete the superflous gpio-example.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some XPedite52xx boards have a legacy boot loader requiring some special
care in the boot wrapper. The use of cuboot-85xx is needed to fix
up embedded device trees, and a custom link address is specified to
accommodate the boot loader and larger kernel image sizes used on X-ES
MPC85xx platforms.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree source files for various MPC85xx boards from Extreme
Engineering Solutions. Supported boards include XPedite5370,
XPedite5200, XPedite5301, XPedite5330, and XCalibur1501.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.
This series provides the following functionality:
- The board can boot with a serial console on UART1
- Ethernet:
UCC1 in RGMII mode
UCC2 in RGMII mode
UCC4 in RMII mode
UCC5 in RMII mode
UCC6 in RMII mode
UCC7 in RMII mode
UCC8 in RMII mode
following patch is necessary for working UCC in RMII mode:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html
- Flash accessed via MTD layer
On this hardware there is an Intel P30 flash, following patch
series is necessary for working with this hardware:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html
- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 4 partitions in nor flash. Also fix nor flash bank width bug. The
flash is capable of x8/x16 width but is configured for x8.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some MPC85xx platforms do support 4 ethernet ports, so make sure the boot
wrapper fixes up all of them in the fdt.
Since MAC addresses are at the end of the bd_t structure there is no harm
in expanding to support 4 MAC address on older 85xx systems that might not
have that many.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.
Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: Leon Woestenberg <leon@sidebranch.com>
Tested-by: Leon Woestenberg <leon@sidebranch.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of commit 404614728f ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.
This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.
Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If anything goes wrong when copying images into the install path, then
the install script should exit with an error code so that 'make' knows
about it and tells the user.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As subject says, add dts files for Xilinx ML510 reference design with
the PCI host bridge device.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that the 4xx NAND driver is available again in arch/powerpc, let's
enable it on Sequoia. This patch also disables the early debug messages
(CONFIG_PPC_EARLY_DEBUG) in the Sequoia defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.
One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In these configuration we expect to have large amounts of memory (> 4G)
and thus will bounce via swiotlb some region of PCI address space.
The outbound windows were wasting 512M of address space by leaving a
gap between the top of the outbound window and the 4G boundary. By
moving the top of the outbound window up to the 4G boundary we can
reclaim the vast majority of the 512M (minus space needed for PEXCSRBAR)
and thus reduces the amount of memory we have to bounce.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For serial flash support we need to:
- Add QE Par IO Bank E device tree node, a GPIO from this bank is
used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").
Also add node for NAND support.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
