Experimentally it can be seen that going into deep sleep (specifically
setting PMU_CLR_DMA and PMU_CLR_BUS in RK3288_PMU_PWRMODE_CON1)
appears to fail unless "aclk_dmac1" is on. The failure is that the
system never signals that it made it into suspend on the GLOBAL_PWROFF
pin and it just hangs.
NOTE that it's confirmed that it's the actual suspend that fails, not
one of the earlier calls to read/write registers. Specifically if you
comment out the "PMU_GLOBAL_INT_DISABLE" setting in
rk3288_slp_mode_set() and then comment out the "cpu_do_idle()" call in
rockchip_lpmode_enter() then you can exercise the whole suspend path
without any crashing.
This is currently not a problem with suspend upstream because there is
no current way to exercise the deep suspend code. However, anyone
trying to make it work will run into this issue.
This was not a problem on shipping rk3288-based Chromebooks because
those devices all ran on an old kernel based on 3.14. On that kernel
"aclk_dmac1" appears to be left on all the time.
There are several ways to skin this problem.
A) We could add "aclk_dmac1" to the list of critical clocks and that
apperas to work, but presumably that wastes power.
B) We could keep a list of "struct clk" objects to enable at suspend
time in clk-rk3288.c and use the standard clock APIs.
C) We could make the rk3288-pmu driver keep a list of clocks to enable
at suspend time. Presumably this would require a dts and bindings
change.
D) We could just whack the clock on in the existing syscore suspend
function where we whack a bunch of other clocks. This is particularly
easy because we know for sure that the clock's only parent
("aclk_cpu") is a critical clock so we don't need to do anything more
than ungate it.
In this case I have chosen D) because it seemed like the least work,
but any of the other options would presumably also work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The USB PHY clock can be configured as (grand) parent of uart0_sclk and
sclk_gpu. It has been observed that UART0 doesn't work reliably in high
speed mode with the PHY clock as input when certain USB devices are
plugged to the USB HOST1 port (see https://crrev.com/c/320543).
Prefix the name of the PHY clock with a '.' in the non-USB muxes to
effectively remove the clock as input from these muxes.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It appears that there is a typo in the rk3288 TRM. For
GRF_SOC_CON0[7] it says that 0 means "vepu" and 1 means "vdpu". It's
the other way around.
How do I know? Here's my evidence:
1. Prior to commit 4d3e84f996 ("clk: rockchip: describe aclk_vcodec
using the new muxgrf type on rk3288") we always pretended that we
were using "aclk_vdpu" and the comment in the code said that this
matched the default setting in the system. In fact the default
setting is 0 according to the TRM and according to reading memory
at bootup. In addition rk3288-based Chromebooks ran like this and
the video codecs worked.
2. With the existing clock code if you boot up and try to enable the
new VIDEO_ROCKCHIP_VPU as a module (and without "clk_ignore_unused"
on the command line), you get errors like "failed to get ack on
domain 'pd_video', val=0x80208". After flipping vepu/vdpu things
init OK.
3. If I export and add both the vepu and vdpu to the list of clocks
for RK3288_PD_VIDEO I can get past the power domain errors, but now
I freeze when the vpu_mmu gets initted.
4. If I just mark the "vdpu" as IGNORE_UNUSED then everything boots up
and probes OK showing that somehow the "vdpu" was important to keep
enabled. This is because we were actually using it as a parent.
5. After this change I can hack "aclk_vcodec_pre" to parent from
"aclk_vepu" using assigned-clocks and the video codec still probes
OK.
6. Rockchip has said so on the mailing list [1].
...so let's fix it.
Let's also add CLK_SET_RATE_PARENT to "aclk_vcodec_pre" as suggested
by Jonas Karlman. Prior to the same commit you could do
clk_set_rate() on "aclk_vcodec" and it would change "aclk_vdpu".
That's because "aclk_vcodec" was a simple gate clock (always gets
CLK_SET_RATE_PARENT) and its direct parent was "aclk_vdpu". After
that commit "aclk_vcodec_pre" gets in the way so we need to add
CLK_SET_RATE_PARENT to it too.
[1] https://lkml.kernel.org/r/1d17b015-9e17-34b9-baf8-c285dc1957aa@rock-chips.com
Fixes: 4d3e84f996 ("clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288")
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Suggested-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Most rk3288-based boards are derived from the EVB and thus use a PWM
regulator for the logic rail. However, most rk3288-based boards don't
specify the PWM regulator in their device tree. We'll deal with that
by making it critical.
NOTE: it's important to make it critical and not just IGNORE_UNUSED
because all PWMs in the system share the same clock. We don't want
another PWM user to turn the clock on and off and kill the logic rail.
This change is in preparation for actually having the PWMs in the
rk3288 device tree actually point to the proper PWM clock. Up until
now they've all pointed to the clock for the old IP block and they've
all worked due to the fact that rkpwm was IGNORE_UNUSED and that the
clock rates for both clocks were the same.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes definition of several clock gate and select register
that is wrong for rk3328 referring to the TRM and vendor kernel.
Also use correct number of softrst registers.
Fix clock definition for:
- clk_crypto
- aclk_h265
- pclk_h265
- aclk_h264
- hclk_h264
- aclk_axisram
- aclk_gmac
- aclk_usb3otg
Fixes: fe3511ad8a ("clk: rockchip: add clock controller for rk3328")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional() API
to get clks that may not always be populated and a way to devm manage clkdev
lookups registered by provider drivers. We also do some refactoring to simplify
the interface between clkdev and the common clk framework so we can reuse the DT
parsing and clk_get() path in provider drivers in the future. This work will
continue in the next few cycles while we convert how providers specify clk
parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk driver
that got support for the G12A SoC. It dominates with almost half the overall
diff, while the second largest part of the diff is in the i.MX clk driver
that gained support for imx8mm SoCs. After that, we have the Actions Semiconductor
and Qualcomm drivers rounding out the big part of the dirstat because they both
got new hardware support for SoCs. The rest is just various updates and non-critical
fixes for existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support
-----BEGIN PGP SIGNATURE-----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=D4Bv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a72d785021 ("clk: ti: Prepare for remove of OF node name")
changed the code to use kasprintf() for provider->clkdm_name but also
changed the offset used later on by three. We don't need to change the
offset as we already have the extra three characters in the format for
kasprintf with "%pOFnxxx".
This caused the clocks with TI_CLK_CLKCTRL_COMPAT to have NULL
clk->clkdm_name for omap4 and 5. And null clkdm_name can cause module
reset, enable, and idle to fail.
The issue can also be seen also when enabling DEBUG for clkctrl.c
and then we start seeing "clock: could not associate" messages for
omap4 and 5 as the generated name is something like "l4_wkclkdm" instead
of "l4_wkup_clkdm" that's needed.
Let's fix the issue with a partial revert of commit a72d785021 ("clk:
ti: Prepare for remove of OF node name").
ALso note that in general code should not depend on the dts node names.
And the node names should be generic types like clock-domain in this case.
This could be fixed later by using separate compatible properties for the
clockdomains, or by adding soc_device_match() table with reg offsets
to the driver. But let's fix the regression first.
Fixes: a72d785021 ("clk: ti: Prepare for remove of OF node name")
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
of_clk_get_by_name() is using -1 for __of_clk_get() index. It will go
to of_parse_clkspec(), and be used for of_parse_phandle_with_args().
Here, if user doesn't specify clock name (= of_clk_get_by_name(np,
NULL)), this index is still -1, and of_parse_phandle_with_args() will
return -EINVAL (This index will be updated if if it had clock name).
clk_get_by_name(np, NULL) should work, then, default index should be 0
instead of -1. This patch fixes it.
Fixes: 4472287a3b ("clk: Introduce of_clk_get_hw_from_clkspec()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* 'clk-parent-rewrite' (early part):
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
* clk-ingenic:
clk: ingenic: Remove set but not used variable 'enable'
clk: ingenic: Fix doc of ingenic_cgu_div_info
clk: ingenic: Fix round_rate misbehaving with non-integer dividers
clk: ingenic: jz4740: Fix gating of UDC clock
* clk-mtk-mux:
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
* clk-qcom-sdm845-pcie:
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
* clk-mtk-crit:
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
* clk-mtk:
clk: mediatek: correct cpu clock name for MT8173 SoC
- Split LCDC into two clks on the Marvell MMP2 SoC
* clk-imx:
clk: imx8mq: add GPIO clocks to clock tree
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: imx: imx8mm: Mark init function __init
clk: imx8mq: Add the missing ARM clock
dt-bindings: imx8mq-clock: Add the missing ARM clock
clk: imx: imx8mq: Fix the rate propagation for arm pll
clk: imx8mq: Add support for the CLKO1 clock
clk: imx8mq: Fix the CLKO2 source select list
clk: imx8mq: Add missing M4 clocks
clk: imx: Add clock driver support for imx8mm
dt-bindings: imx: Add clock binding doc for imx8mm
clk: imx: Add PLLs driver for imx8mm soc
clk: imx5: add imx5_SCC2_IPG_GATE
clk: imx: scu: add set parent support
clk: imx: scu: add fallback compatible string support
clk: imx8mq: Make parent names arrays const pointers
clk: imx: Make parents const pointer in mux wrappers
clk: imx: Make parent_names const pointer in composite-8m
* clk-samsung:
clk: samsung: s3c2443: Mark expected switch fall-through
clk: samsung: exynos5: Fix kfree() of const memory on setting driver_override
clk: samsung: exynos5: Fix possible NULL pointer exception on platform_device_alloc() failure
clk: samsung: exynos5433: Add selected IMEM clocks
clk: samsung: dt-bindings: Document Exynos5433 IMEM CMU
clk: samsung: exynos5433: Fix name typo in sssx
clk: samsung: exynos5433: Fix definition of CLK_ACLK_IMEM_{200, 266} clocks
clk: samsung: dt-bindings: Add Exynos5433 IMEM CMU clock IDs
* clk-ti:
clk: clk-twl6040: Fix imprecise external abort for pdmclk
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
* clk-uniphier-gear:
clk: uniphier: Fix update register for CPU-gear
* clk-mmp2-lcdc:
clk: mmp2: separate LCDC peripheral clk form the display clock
dt-bindings: marvell,mmp2: Add clock id for the LCDC clock
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
The API between clk.c and clkdev.c is purely getting the clk_hw
structure (or the struct clk if it's not CCF) and then turning that
struct clk_hw pointer into a struct clk pointer via clk_hw_create_clk().
There's no need to complicate clkdev.c with these DT parsing details
that are only relevant to the common clk framework. Move the DT parsing
logic into the core framework and just expose the APIs to get a clk_hw
pointer and convert it.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We'd like to have a pointer to the device that's consuming a particular
clk in the clk framework so we can link the consumer to the clk provider
with a PM device link. Add a device argument to clk_hw_create_clk() for
this so it can be used in subsequent patches to add and remove the link.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We want to get struct clk_hw pointers from a DT clk specifier (i.e. a
clocks property) so that we can find parent clks without searching for
globally unique clk names. This should save time by avoiding the global
string search for clks that are external to the clock controller
providing the clk and let us move away from string comparisons in
general.
Introduce of_clk_get_hw_from_clkspec() which is largely the DT parsing
part of finding clks implemented in clkdev.c and have that return a
clk_hw pointer instead of converting that into a clk pointer. This lets
us push up the clk pointer creation to the caller in clk_get() and
avoids the need to push the dev_id and con_id throughout the DT parsing
code.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently, the core->dev entry is populated only if runtime PM is
enabled. Doing so prevents accessing the device structure in any
case.
Keep the same logic but instead of using the presence of core->dev as
the only condition, also check the status of
pm_runtime_enabled(). Then, we can set the core->dev pointer at any
time as long as a device structure is available.
This change will help supporting device links in the clock subsystem.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
[sboyd@kernel.org: Change to a boolean flag]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The __clk_get() function is practically a private clk implementation
detail now. No architecture defines it, and given that new code should
be using the common clk framework there isn't a need for it to keep
existing just to serve clkdev purposes. Let's fold it into the
__clk_create_clk() function and make that a little more generic by
renaming it to clk_hw_create_clk(). This will allow the framework to
create a struct clk handle to a particular clk_hw pointer and link it up
as a consumer wherever that's needed.
Doing this also lets us get rid of the __clk_free_clk() API that had to
be kept in sync with __clk_put(). Splitting that API up into the "link
and unlink from consumer list" phase and "free the clk pointer" phase
allows us to reuse that logic in a couple places, simplifying the code.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX8MQ has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Correct cpu clock name from ca57 to ca72 since MT8173 does use cortex-a72.
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make the entire combination of plls to be one single clock. The parents used
for bypasses are specified each as an index in the parents list.
The determine_rate does a lookup throughout all the possible combinations
for all the divs and returns the best possible 'setup' which in turn is used
by set_rate later to set up all the divs and bypasses.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On NXP's i.MX SoCs with system controller inside, CPU frequency
scaling can ONLY be done by system controller firmware, and it
can ONLY be requested from secure mode, so Linux kernel has to
call ARM SMC to trap to ARM-Trusted-Firmware to request system
controller firmware to do CPU frequency scaling.
This patch adds i.MX system controller CPU frequency scaling support,
it reuses cpufreq-dt driver and implement the CPU frequency scaling
inside SCU clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently, DRAM-related clocks are not marked with CLK_IS_CRITICAL
for MT6797. This causes memory corruption when the system is
booted without clk_ignore_unused.
This patch marks MUX ddrphycfg_sel as well as gates infra_dramc_f26m
and infra_dramc_b_f26m as CLK_IS_CRITICAL.
Signed-off-by: Jasper Mattsson <jasu@njomotys.info>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is required to mark gates as CLK_IS_CRITICAL.
Signed-off-by: Jasper Mattsson <jasu@njomotys.info>
Acked-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is required to mark outputs of certain MUXes as CLK_IS_CRITICAL.
Signed-off-by: Jasper Mattsson <jasu@njomotys.info>
Acked-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PCIe PIPE clock in the GCC is fed by the PIPE clock coming from the
PHY, describe this relationship.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/clk/ingenic/cgu.c: In function 'ingenic_pll_recalc_rate':
drivers/clk/ingenic/cgu.c:86:15: warning:
variable 'enable' set but not used [-Wunused-but-set-variable]
It's not used after commit ab27eb4bc3 ("clk: ingenic: Add code to
enable/disable PLLs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This register read is a leftover of a previous read/modify/write. We now use
regmap_update_bits(), so we don't need it anymore.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The MUX clock of dpi1_sel should select the closet clock for itself.
We could add this flag to enable this function of MUX in CCF.
Signed-off-by: chunhui dai <chunhui.dai@mediatek.com>
Signed-off-by: wangyan wang <wangyan.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add MUX_GATE_FLAGS_2 for the clock which needs to set two falgs.
Such as some mux need to set the flags of "CLK_MUX_ROUND_CLOSEST".
Signed-off-by: chunhui dai <chunhui.dai@mediatek.com>
Signed-off-by: wangyan wang <wangyan.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The 'div' field does not represent a number of bits used to divide
(understand: right-shift) the divider, but a number itself used to
divide the divider.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Take a parent rate of 180 MHz, and a requested rate of 4.285715 MHz.
This results in a theorical divider of 41.999993 which is then rounded
up to 42. The .round_rate function would then return (180 MHz / 42) as
the clock, rounded down, so 4.285714 MHz.
Calling clk_set_rate on 4.285714 MHz would round the rate again, and
give a theorical divider of 42,0000028, now rounded up to 43, and the
rate returned would be (180 MHz / 43) which is 4.186046 MHz, aka. not
what we requested.
Fix this by rounding up the divisions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We intended to print "ret" but there is a copy and paste bug from the
previous error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stop the search for parent rate when exact match is found.
This makes for 3 clk_round_rate() calls instead of 64 of them on
SAMA5D2-based board when searching for 12.288MHz clock.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk-lpss.h is solely x86 related header. Move it to correct folder.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Custom approximation of fractional-divider may not need parent clock
rate checking. For example Rockchip SoCs work fine using grand parent
clock rate even if target rate is greater than parent.
This patch checks parent clock rate only if CLK_SET_RATE_PARENT flag
is set.
For detailed example, clock tree of Rockchip I2S audio hardware.
- Clock rate of CPLL is 1.2GHz, GPLL is 491.52MHz.
- i2s1_div is integer divider can divide N (N is 1~128).
Input clock is CPLL or GPLL. Initial divider value is N = 1.
Ex) PLL = CPLL, N = 10, i2s1_div output rate is
CPLL / 10 = 1.2GHz / 10 = 120MHz
- i2s1_frac is fractional divider can divide input to x/y, x and
y are 16bit integer.
CPLL --> | selector | ---> i2s1_div -+--> | selector | --> I2S1 MCLK
GPLL --> | | ,--------------' | |
`--> i2s1_frac ---> | |
Clock mux system try to choose suitable one from i2s1_div and
i2s1_frac for master clock (MCLK) of I2S1.
Bad scenario as follows:
- Try to set MCLK to 8.192MHz (32kHz audio replay)
Candidate setting is
- i2s1_div: GPLL / 60 = 8.192MHz
i2s1_div candidate is exactly same as target clock rate, so mux
choose this clock source. i2s1_div output rate is changed
491.52MHz -> 8.192MHz
- After that try to set to 11.2896MHz (44.1kHz audio replay)
Candidate settings are
- i2s1_div : CPLL / 107 = 11.214945MHz
- i2s1_frac: i2s1_div = 8.192MHz
This is because clk_fd_round_rate() thinks target rate
(11.2896MHz) is higher than parent rate (i2s1_div = 8.192MHz)
and returns parent clock rate.
Above is current upstreamed behavior. Clock mux system choose
i2s1_div, but this clock rate is not acceptable for I2S driver, so
users cannot replay audio.
Expected behavior is:
- Try to set master clock to 11.2896MHz (44.1kHz audio replay)
Candidate settings are
- i2s1_div : CPLL / 107 = 11.214945MHz
- i2s1_frac: i2s1_div * 147/6400 = 11.2896MHz
Change i2s1_div to GPLL / 1 = 491.52MHz at same
time.
If apply this commit, clk_fd_round_rate() calls custom approximate
function of Rockchip even if target rate is higher than parent.
Custom function changes both grand parent (i2s1_div) and parent
(i2s_frac) settings at same time. Clock mux system can choose
i2s1_frac and audio works fine.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@kernel.org: Make function into a macro instead]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Several clock controller drivers define a list of clk_hw devices, and then
register those devices in probe() before using common code to process the
rest of initialization. Extend the common code to accept a list of clk_hw
devices to process, thus eliminating many duplicate implementations.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add common clock driver for Actions Semi S500 SoC.
Signed-off-by: Edgar Bernardi Righi <edgar.righi@lsitec.org.br>
[Mani: cleaned up the driver]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
S500 SoC requires configurable delay for different PLLs. Hence, add
a separate macro for declaring a PLL with configurable delay and also
modify the existing OWL_PLL_NO_PARENT macro to use default delay so
that no need to modify the existing S700/S900 drivers.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It calls another __init marked function and thus causes a section
mismatch if we don't mark it this way.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CFG/M/N/D registers are at an offset of 0x20 from the CMD register
only for blsp1_uart3 clock, so add it for uart3 only.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
