Adds an optional infrustructure component to bridge that would allow
native vlan filtering in the bridge. Each bridge port (as well
as the bridge device) now get a VLAN bitmap. Each bit in the bitmap
is associated with a vlan id. This way if the bit corresponding to
the vid is set in the bitmap that the packet with vid is allowed to
enter and exit the port.
Write access the bitmap is protected by RTNL and read access
protected by RCU.
Vlan functionality is disabled by default.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configs BRIDGE=y and IPV6=m, this build error occurs:
br_multicast.c:(.text+0xa3341): undefined reference to `ipv6_dev_get_saddr'
BRIDGE_IGMP_SNOOPING is boolean; if it were tristate, then adding
depends on IPV6 || IPV6=n
to BRIDGE_IGMP_SNOOPING would be a good fix. As it is currently,
making BRIDGE depend on the IPV6 config works.
Reported-by: Patrick Schaaf <netdev@bof.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast calls ip_send_check(), so it should depend on INET.
built-in:
br_multicast.c:(.text+0x88cf4): undefined reference to `ip_send_check'
or modular:
ERROR: "ip_send_check" [net/bridge/bridge.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the core functionality of IGMP snooping support
without actually hooking it up. So this patch should be a no-op
as far as the bridge's external behaviour is concerned.
All the new code and data is controlled by the Kconfig option
BRIDGE_IGMP_SNOOPING. A run-time toggle is also available.
The multicast switching is done using an hash table that is
lockless on the read-side through RCU. On the write-side the
new multicast_lock is used for all operations. The hash table
supports dynamic growth/rehashing.
The hash table will be rehashed if any chain length exceeds a
preset limit. If rehashing does not reduce the maximum chain
length then snooping will be disabled.
These features may be added in future (in no particular order):
* IGMPv3 source support
* Non-querier router detection
* IPv6
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the STP demux layer for receiving STP PDUs instead of directly
registering with LLC.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use LLC for the receive path of Spanning Tree Protocol packets.
This allows link local multicast packets to be received by
other protocols (if they care), and uses the existing LLC
code to get STP packets back into bridge code.
The bridge multicast address is also checked, so bridges using
other link local multicast addresses are ignored. This allows
for use of different multicast addresses to define separate STP
domains.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.
The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.
Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
