In order to allow runtime PM, the device needs to be passed on
to the register function. Audiomix clock controller, used on
i.MX8MP and future platforms, registers a pll14xx and has runtime
PM support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audiomix on i.MX8MP registers two gates that share the same enable count
but use the same bit to control the gate instead of two bits. By adding
the flag IMX_CLK_GATE2_SINGLE_BIT we allow the gate2 to use the generic
gate ops for enable, disable and is_enabled.
For the disable_unused, nothing happens if this flag is specified.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use readl_relaxed_poll_timeout() for PLL lock wait which can simplify the
code a lot.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove many unnecessary blank lines for cleanup.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Moving to support aarch32 mode on aarch64 hardware, need to drop
the dependency on ARM64 to make the driver could be selected for
ARM32.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM clk could only source from divcore or hsrun_divcore.
Follow what we already used on i.MX7D and i.MX8M SoCs, use
imx_clk_hw_cpu API. When ARM core is running normaly,
whether divcore or hwrun_divcore will finally source
from SPLL_PFD0. However SPLL_PFD0 is marked with CLK_SET_GATE,
so we need to disable SPLL_PFD0, when configure the rate.
So add CORE and HSRUN_CORE virtual clk to make it easy to
configure the clk using imx_clk_hw_cpu API.
Since CORE and HSRUN_CORE already marked with CLK_IS_CRITICAL, no
need to set ARM as CLK_IS_CRITICAL. And when set the rate of ARM clk,
prograting it the parent with CLK_SET_RATE_PARENT will finally set
the SPLL_PFD0 clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting a CAN bitrate of 800kbit/s fails with a bitrate error of 1.3% if the
flexcan module is clocked at 30MHz (CAN_CLK_ROOT). This patch changes the clock
frequency from 30MHz to 40MHz which allows to support all bitrates recommended
by CiA.
The patch sets CAN_CLK_SEL to 80MHz by changing its clock parent from
CLK_PLL3_60M to CLK_PLL3_80M. The post-divider CAN_CLK_PODF is set to /2 by
default which makes 40MHz CAN_CLK_ROOT from its parent CAN_CLK_SEL.
Background:
CAN in Automation document 102 (CiA102) recommends the CAN bitrates 10, 20, 50,
125, 250, 500, 800 and 1000kbit/s.
With the flexcan serial clock at 30MHz (original value) setting some common
bitrates ("ip link set canX type can bitrate <bitrate>") gives the following
results:
requested value / actually set value
5000: bitrate 5000 sample-point 0.708
10000: bitrate 10000 sample-point 0.866
20000: bitrate 20000 sample-point 0.866
40000: bitrate 40000 sample-point 0.866
50000: bitrate 50000 sample-point 0.866
80000: bitrate 80000 sample-point 0.866
100000: bitrate 100000 sample-point 0.866
125000: bitrate 125000 sample-point 0.875
250000: bitrate 250000 sample-point 0.866
400000: bitrate 400000 sample-point 0.866
500000: bitrate 500000 sample-point 0.866
666666: bitrate 666666 sample-point 0.800
800000: bitrate 789473 sample-point 0.789 !!!bitrate error 1.3%
1000000: bitrate 1000000 sample-point 0.733
With the flexcan serial clock at 40MHz (new value) we get this:
5000: no more possible
10000: bitrate 10000 sample-point 0.875
20000: bitrate 20000 sample-point 0.875
40000: bitrate 40000 sample-point 0.850
50000: bitrate 50000 sample-point 0.875
80000: bitrate 80000 sample-point 0.850
100000: bitrate 100000 sample-point 0.875
125000: bitrate 125000 sample-point 0.875
250000: bitrate 250000 sample-point 0.875
400000: bitrate 400000 sample-point 0.850
500000: bitrate 500000 sample-point 0.875
666666: bitrate 666666 sample-point 0.800
800000: bitrate 800000 sample-point 0.800
1000000: bitrate 1000000 sample-point 0.750
A drawback of the modification is that 5kbit/s is no more supported.
Setting the flexcan serial clock to 60MHz or 80MHz would produce similar
results but with losing even more bitrates at the lower end.
Changing the flexcan serial clock to 40MHz might apply for other SoCs
using the flaxcan module as well (e.g. imx6q/d/s..). But since I don't
have such hardware to test I did not add this to the patch.
Signed-off-by: Georg Waibel <georg.waibel@wiedemann-group.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
majority of the diff is the normal collection of driver additions for new SoCs
and non-critical clk data fixes and updates. The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and Unisoc
support added a handful of big drivers for new SoCs but that's not really the
whole story because those new drivers tend to add large numbers of lines of clk
data. There's a handful of AT91 clk drivers added this time around too and a
bunch of improvements to drivers like the i.MX driver. All around lots of
updates and fixes in various clk drivers which is good to see.
The core framework has only one real major change which has been baking in next
for the past couple months. It fixes the framework so that it stops caching a
clk's phase when the phase clk_op returns an error. Before this change we would
consider some negative errno as a phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for pll1443x table,
and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need to
change ARM PLL frequency. Thus, we can support core running above
1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate for
getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks
-----BEGIN PGP SIGNATURE-----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=ZoI6
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's not much to see in the core framework this time around.
Instead the majority of the diff is the normal collection of driver
additions for new SoCs and non-critical clk data fixes and updates.
The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and
Unisoc support added a handful of big drivers for new SoCs but that's
not really the whole story because those new drivers tend to add large
numbers of lines of clk data. There's a handful of AT91 clk drivers
added this time around too and a bunch of improvements to drivers like
the i.MX driver. All around lots of updates and fixes in various clk
drivers which is good to see.
The core framework has only one real major change which has been
baking in next for the past couple months. It fixes the framework so
that it stops caching a clk's phase when the phase clk_op returns an
error. Before this change we would consider some negative errno as a
phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and
at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for
pll1443x table, and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need
to change ARM PLL frequency. Thus, we can support core running
above 1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate
for getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for
imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock
Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and
M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (146 commits)
clk: sprd: fix to get a correct ibias of pll
dt-bindings: imx8mm-clock: Fix the file path
dt-bindings: imx8mq-clock: Fix the file path
clk: qcom: rpmh: Drop unnecessary semicolons
clk: qcom: rpmh: Simplify clk_rpmh_bcm_send_cmd()
clk: tegra: Use NULL for pointer initialization
clk: sprd: add clocks support for SC9863A
clk: sprd: support to get regmap from parent node
clk: sprd: Add macros for referencing parents without strings
clk: sprd: Add dt-bindings include file for SC9863A
dt-bindings: clk: sprd: add bindings for sc9863a clock controller
dt-bindings: clk: sprd: rename the common file name sprd.txt to SoC specific
clk: sprd: add gate for pll clocks
MAINTAINERS: dt: update reference for arm-integrator.txt
clk: mmp2: Fix bit masks for LCDC I/O and pixel clocks
clk: mmp2: Add clock for fifth SD HCI on MMP3
dt-bindings: marvell,mmp2: Add clock id for the fifth SD HCI on MMP3
clk: mmp2: Add clocks for the thermal sensors
dt-bindings: marvell,mmp2: Add clock ids for the thermal sensors
clk: mmp2: add the GPU clocks
...
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 666aed2d13 ("clk: imx: scu: add set parent support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/aad021e432b3062c142973d09b766656eec18fde.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: fe37b48204 ("clk: imx: add scu clock common part")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/10e97a04980d933b2cfecb6b124bf9046b6e4f16.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The device needs to be passed on to the clk_hw_register.
Fixes: 1f9aec9662 ("clk: imx: clk-gate2: Switch to clk_hw based API")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PXP has a single CCGR clock gate, gating both the IPG_CLK_ROOT and
the MAIN_AXI_CLK_ROOT. Add a single clock to cover both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
enet_qos is for eqos tsn AXI bus clock whose clock source is from
ccm_enet_axi_clk_root, and controlled by CCM_CCGR59(offset 0x43b0)
and CCM_CCGR64(offset 0x4400), so correct enet_qos root clock's
parent clock to sim_enet.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MP_CLK_HDMI_AXI should be from imx8mp_media_axi_sels instead
of imx8mp_media_apb_sels, fix it.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not good to use enable/disable for PLLv4 which needs time to
lock, because enable/disable is expected to be able run in
interrupt context. So use prepare/unprepare.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pfdv2 is only used in i.MX7ULP. To get best pfd output, the i.MX7ULP
Datasheet defines two best PLL rate and pfd frac.
Per Datasheel
All PLLs on i.MX 7ULP either have VCO base frequency of
480 MHz or 528 MHz. So when determine best rate, we also
determine best parent rate which could match the requirement.
For some reason the current parent might not be 480MHz or 528MHz,
so we still take current parent rate as a choice.
And we also enable flag CLK_SET_RATE_PARENT to let parent rate
to be configured.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per clk_ops, compared with round_rate, determine_rate could optionally
support the parent clock that should be used to provide the clock rate.
In this patch, the parent clock is just parent->rate as round_rate.
The following patch will calculate the best parent clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No need to initialize 'ret' in many functions, as it will get
the return value from function call, so remove the initializtion
of 'ret'.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When pll type is invalid, ONLY output error message is NOT enough,
should return error immediately.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clk
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clk.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clock
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which violates the CCM.
There is a CORE_SEL slice before A53 core, we need to configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clock
Fixes: db27e40b27 ("clk: imx8mq: Add the missing ARM clock")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MP, internal HDMI 27M clock is actually 24MHz, so rename
the IMX8MP_CLK_HDMI_27M to IMX8MP_CLK_HDMI_24M.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is nothing in use from init.h/of.h, remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is nothing in use from init.h/of.h, remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
slab.h is necessary and included indirectly by clkdev.h,
actually, there is nothing in use from clkdev.h, so just
include slab.h instead of clkdev.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7ULP clock driver is provider, NOT consumer, so clk-provider.h
should be used instead of clk.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No need to initialize flags as 0, remove the initialization.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M SoCs clock driver are provider, NOT consumer, so clk-provider.h
should be used instead of clk.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CLKO2 support, which is useful for debugging purposes.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CLKO1 clock source select list is the following as per the i.MX8MM
Reference Manual (put in increasing order):
000 - 24M_REF_CLK
001 - SYSTEM_PLL1_CLK
010 - None
011 - SYSTEM_PLL1_DIV4
100 - AUDIO_PLL2_CLK
101 - SYSTEM_PLL2_DIV2
110 - VPU_PLL_CLK
111 - SYSTEM_PLL1_DIV10
Fix it accordingly.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are several clock slices, current composite code
only support bus/ip clock slices, it could not support core
slice.
So introduce a new API imx8m_clk_hw_composite_core to support
core slice. To core slice, post divider with 3 bits width and
no pre divider. Other fields are same as bus/ip slices.
Add a flag IMX_COMPOSITE_CORE for the usecase.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add ocotp root clk, then when using nvmem to read fuse, clk
could be managed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add new frequency entries to pll1443x table to meet different
display settings requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.mx8mn has support for clock gating the snvs module.
Add it into clock tree so that rtc-snvs driver could use it.
Note this will also be required in the snvs_pwrkey driver,
once support for clock management will be added.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
