in case of ehci phy mode; regulator of phy
should be enabled before initializing the
usbhs core driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Steve Calfee <stevecalfee@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If cable is not connected to peripheral only board when initializing the
gadget driver, then runtime pm calls are out-of-sync and the musb cannot
idle with omap2430.c. This was noted on Nokia N900 where musb prevented the
CPU to be able to enter deeper retention idle state.
This was working in 2.6.38 before runtime pm conversions but there musb
smart standby/idle modes were configured statically where they are now
updated runtime depending on use and cable status.
Reason for out-of-sync is that runtime pm is activated in function
musb_gadget.c: usb_gadget_probe_driver but suspended only in OTG mode if
cable is not connected when initializing. In peripheral only mode this leads
to out-of-sync runtime pm since runtime pm remain active and is activated
another time in omap2430.c: musb_otg_notifications for VBUS Connect event
and thus cannot suspend for VBUS Disconnect event since the use count remains
active.
Fix this by moving cable status check and pm_runtime_put call in
usb_gadget_probe_driver out of is_otg_enabled block.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Recent runtime pm and hwmod conversions for 2.6.39 broke the musb peripheral
mode OMAP retention idle on boards where the board mode in struct
musb_hdrc_platform_data is set to MUSB_PERIPHERAL.
These conversions changed the way how the OTG_SYSCONFIG register is
configured and used in runtime. Before 2.6.39 smart standby/idle modes were
activated statically in OTG_SYSCONFIG. Those modes allow that the musb is
able to idle when peripheral device is not connected to host.
In 2.6.39 the OTG_SYSCONFIG is updated runtime depending on VBUS status.
No standby/idle modes are used when device is connected and force
standby/idle when disconnected.
Unfortunately VBUS disconnect event that handles the disconnect case lets
the peripheral musb to idle only when board mode is MUSB_OTG. Fix this by
checking the peripheral mode also.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isd200 sub-driver increments the command serial number despite not
using it at all in it's routine for sending internal scsi commands.
Remove the increment to prepare for removing the serial_number field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit b02d0ed677 ('xhci: Change
hcd_priv into a pointer') added calls to kzalloc() and kfree() in
xhci-pci.c. On most architectures <linux/slab.h> is indirectly
included, but on some it is not.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_create_sysfs_intf_files() function always returned zero even
if it failed to create sysfs fails. Since this is a desired behaviour
there is no need to return return code at all. This commit changes
function's return type (form int) to void.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1452b) adds a new test case to the usbtest driver. Test
24 exercises the unlink-from-queue pathways in the host. It queues a
user-specified number of bulk-OUT URBs of user-specified size, unlinks
the fourth- and second-from-last URBs in the queue, and then waits to
see if all the URBs complete in the expected way (except of course
that the unlinked URBs might complete normally, if they weren't
unlinked soon enough).
This new test has confirmed the existence of a bug in the ehci-hcd
driver, to be fixed by a separate patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tegra USB1 port needs to issue Port Reset twice internally, otherwise it
fails to enumerate devices attached to it
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
[ squash two patches into one and minor style cleanups ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch uses the resource_size help function instead of
manually calculating the resource size. It can reduce the chance
of introducing off-by-one errors.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __devinit and __devexit macros were added to probe and remove
functions. The macros move the probe and remove functions to the
devinit and devexit sections.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit fixes an embarrassing bug in the "storage_common:
use kstrto*()" patch which caused fsg_store_ro() to return
zero instead of the length of the consumed buffer.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the_controller is allocated in dummy_hcd_probe() and is NULL if the
allocation failed. The probe function of the udc driver is dereferencing
this pointer and fault.
Alan Stern suggested to abort the dummy_hcd driver probing so the module
is not loaded. The is abort-on-error has been also added to the udc
driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB type detections fails, we run into default and return 0.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current renesas_usbhs was designed to save power when USB is not connected.
And it assumed platform uses callback to notify connection/disconnection
by external interrupt.
But some SuperH / platform board doesn't have such feature.
This patch adds autonomy mode which detect USB connection/disconnection
by internal interrupt.
But power will be always ON when autonomy mode is selected.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This delay is used to overjump debounce.
And, this patch also move usbhsc_drvcllbck_notify_hotplug to global,
because it will be called from other files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbhs_status_get_each_irq/usbhs_irq_callback_update might be called
with mod == NULL
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbhs_pdev_to_priv function will be used in other files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The callback function which is called from platform must be removed
if module removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are some USB Host which doesn't notice disconnection at once.
And it might try some request after reconnection with old settings.
Current renesas_usbhs will crash in such case.
This patch prevent this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current renesas_usbhs driver was using spin_trylock to avoid
dead lock / nest lock.
But acording to CONFIG_DEBUG_SPINLOCK, it is BUG under UP environment.
This patch add usbhsg_trylock to avoid this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because pipe buffer allocation is very picky and difficult,
current renesas_usbhs driver is not caring pipe re-allocation.
In this situation, driver will create new pipe without caring old pipe
if "usbhsg_ep_enable" is called after "usbhsg_ep_disable" on current driver.
This mean the limited pipe and buffer will be used as waste.
But it is possible to re-use same buffer to same pipe.
By this patch, driver will initialize pipe when it detected new connection or
new gadget, and doesn't try re-allocation for same pipe in above case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pipe buffer should be cleaned before using it,
but should NOT be cleaned in pipe "prepare" function.
Because the pipe might be working in such timing.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_printer reqiured "set interface" request from host. Not all hosts send
this request. This patch enable the interface when it get "set
configuration" request from host.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stripping the direction bit off will produce an
invalid descriptor.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code doesn't set it, so linux complains about
it when connected, and ignores the device:
[104611.068082] usb 1-5: new high speed USB device using ehci_hcd and address 127
[104611.088368] usb 1-5: Invalid ep0 maxpacket: 0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current code returns 0 even if it can't handle the request.
This leads to timeouts when an unhandled request is sent:
Bus 001 Device 003: ID 0525:c0de Netchip Technology, Inc.
Device Descriptor:
[..]
can't get device qualifier: Connection timed out
[..]
change the code to return EOPNOTSUPP in such cases.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Network interface is handled by upcoming gt_b3730 module.
Removed "GT-B3710" from comment, it is another modem with another USB ID.
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch
- ensures no IO takes place during resets
- reports resets to user space
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem where data received from the gps is sometimes
transferred incompletely to the serial port. If used in native mode now
all data received via the bulk queue will be forwarded to the serial
port.
Signed-off-by: Hermann Kneissel <herkne@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for the TavIR STK500 (id 0403:FA33)
Atmel AVR programmer device based on FTDI FT232RL.
Signed-off-by: Benedek László <benedekl@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested on my phone, the ttyUSB device is created and is fully
functional.
Signed-off-by: Elizabeth Jennifer Myers <elizabeth@sporksirc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds 4 device IDs for CP2102 based devices manufactured by
AC-Services. See http://www.ac-services.eu for further info.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 806e8f8fcc.
To quote Alan Stern:
The necessity for this patch has been under discussion.
It turns out the UDC that Mian has been working on and Felipe's
UDC have contradictory requirements. Mian's UDC driver wants a
bulk-OUT transfer length to be shorter than the maxpacket size
if a short packet is expected, whereas Felipe's UDC hardware
always needs bulk-OUT transfer lengths to be evenly divisible by
the maxpacket size.
Mian has agreed to go back over the driver to resolve this
conflict. This means we probably will not want this patch after
all. (In fact, we may ultimately decide to change the gadget
framework to require that bulk-OUT transfer lengths _always_ be
divisible by the maxpacket size -- only the g_file_storage and
g_mass_storage gadgets would need to be changed.)
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 5808544690.
To quote Richard:
I don't think this should be mainlined. It was a
misunderstanding on my part. If you see all the other hdc
drivers in the same location, they all do the same thing (i.e.
clear the interrupt status first, then do the work) that
"glitch" I think I saw was actually two back-to-back
interrupts.
Sebastian (the original author of isp1760) explained it to me a
few days after my submission.
sorry for the confusion
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit replaces the usage of strict_strtoul() (which
became deprecated after commit 33ee3b2e) with kstrtouint().
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Atheros AR71XX/AR7240 SoCs have a built-in OHCI controller.
This patch adds the necessary glue code to make the generic OHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A Synopsys USB core used in various SoCs has a bug which might cause
that the host controller not issuing ping.
When software uses the Doorbell mechanism to remove queue heads, the
host controller still has references to the removed queue head even
after indicating an Interrupt on Async Advance. This happens if the last
executed queue head's Next Link queue head is removed.
Consequences of the defect:
The Host controller fetches the removed queue head, using memory that
would otherwise be deallocated.This results in incorrect transactions on
both the USB and system memory. This may result in undefined behavior.
Workarounds:
1) If no queue head is active (no Status field's Active bit is set)
after removing the queue heads, the software can write one of the valid
queue head addresses to the ASYNCLISTADDR register and deallocate the
removed queue head's memory after 2 microframes.
If one or more of the queue heads is active (the Active bit is set in
the Status field) after removing the queue heads, the software can delay
memory deallocation after time X, where X is the time required for the
Host Controller to go through all the queue heads once. X varies with
the number of queue heads and the time required to process periodic
transactions: if more periodic transactions must be performed, the Host
Controller has less time to process asynchronous transaction processing.
2) Do not use the Doorbell mechanism to remove the queue heads. Disable
the Asynchronous Schedule Enable bit instead.
The bug has been discussed on the linux-usb-devel mailing-list
four years ago, the original thread can be found here:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg45345.html
This patch implements the first workaround as suggested by David Brownell.
The built-in USB host controller of the Atheros AR7130/AR7141/AR7161 SoCs
requires this to work properly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Atheros AR71XX/AR91XX SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disable the optional PM feature inside the Hudson3 platform under
the following conditions:
1. If an isochronous device is connected to xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
The PM feature needs to be disabled to eliminate PLL startup delays when the
link comes out of low power state. The performance of DMA data transfer could
be impacted if system delay were encountered and in addition to the PLL start
up delays. Disabling the PM would leave room for unpredictable system delays
in order to guarantee uninterrupted data transfer to isochronous audio or
video stream devices that require time sensitive information. If data in an
audio/video stream was interrupted then erratic audio or video performance
may be encountered.
AMD PLL quirk is already implemented in OHCI/EHCI driver. After moving the
quirk code to pci-quirks.c and export them, xHCI driver can call it directly
without having the quirk implementation in itself.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
On a resume, when the power is lost during hibernate, the USB core will
call hub_reset_resume for the xHCI USB 2.0 roothub, but not for the USB
3.0 roothub:
[ 164.748310] usb usb1: root hub lost power or was reset
[ 164.748353] usb usb2: root hub lost power or was reset
[ 164.748487] usb usb3: root hub lost power or was reset
[ 164.748488] xhci_hcd 0000:01:00.0: Stop HCD
...
[ 164.870039] hub 4-0:1.0: hub_resume
...
[ 164.870054] hub 3-0:1.0: hub_reset_resume
This causes issues later, because the USB core assumes the USB 3.0 hub
attached to the USB 3.0 roothub is still active. It attempts to queue a
control URB for the external hub, which fails because all the device
slot contexts were released when the USB 3.0 roothub lost power:
[ 164.980044] hub 4-1:1.0: hub_resume
[ 164.980047] xhci_hcd 0000:01:00.0: Get port status returned 0x10101
[ 164.980049] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980053] hub 3-0:1.0: port 1: status 0101 change 0001
[ 164.980056] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980060] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc90008948440, 32'h202e1, 4'hf);
[ 164.980062] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980066] xhci_hcd 0000:01:00.0: clear port connect change, actual port 0 status = 0x2e1
[ 164.980069] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980072] xhci_hcd 0000:01:00.0: get port status, actual port 1 status = 0x2a0
[ 164.980074] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980077] xhci_hcd 0000:01:00.0: Get port status returned 0x100
[ 164.980079] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980082] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980085] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980088] hub 4-1:1.0: port 4: status 0000 change 0000
[ 164.980091] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980094] hub 4-1:1.0: activate --> -22
[ 164.980113] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980117] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980119] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980123] hub 4-1:1.0: can't resume port 4, status -22
[ 164.980126] hub 4-1:1.0: port 4 status ffff.ffff after resume, -22
[ 164.980129] usb 4-1.4: can't resume, status -22
[ 164.980131] hub 4-1:1.0: logical disconnect on port 4
This causes issues when a USB 3.0 hard drive is attached to the external
USB 3.0 hub when the system is hibernated:
[ 6249.849653] sd 8:0:0:0: [sdb] Unhandled error code
[ 6249.849659] sd 8:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 6249.849663] sd 8:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 2a 08 00 00 02 00
[ 6249.849671] end_request: I/O error, dev sdb, sector 10760
Make sure to inform the USB core that *both* xHCI roothubs lost power.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch clear PORT_POWER when suspend a USB3.0 device behind a USB3.0
external hub, so the system can suspend and resume.
Note USB3.0 device may not work after system resume and this is a temporary
workaround. The correct fix will be in future patches.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If I unplug a device while the UAS driver is loaded, I get an oops
in usb_free_streams(). This is because usb_unbind_interface() calls
usb_disable_interface() which calls usb_disable_endpoint() which sets
ep_out and ep_in to NULL. Then the UAS driver calls usb_pipe_endpoint()
which returns a NULL pointer and passes an array of NULL pointers to
usb_free_streams().
I think the correct fix for this is to check for the NULL pointer
in usb_free_streams() rather than making the driver check for this
situation. My original patch for this checked for dev->state ==
USB_STATE_NOTATTACHED, but the call to usb_disable_interface() is
conditional, so not all drivers would want this check.
Note from Sarah Sharp: This patch does avoid a potential dereference,
but the real fix (which will be implemented later) is to set the
.soft_unbind flag in the usb_driver structure for the UAS driver, and
all drivers that allocate streams. The driver should free any streams
when it is unbound from the interface. This avoids leaking stream rings
in the xHCI driver when usb_disable_interface() is called.
This should be queued for stable trees back to 2.6.35.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Currently, when resetting a device, xHCI driver disables all but one
endpoints and frees their rings, but leaves alone any streams that
might have been allocated. Later, when users try to free allocated
streams, we oops in xhci_setup_no_streams_ep_input_ctx() because
ep->ring is NULL.
Let's free not only rings but also stream data as well, so that
calling free_streams() on a device that was reset will be safe.
This should be queued for stable trees back to 2.6.35.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
This patch adds host USB high speed driver for samsung S5P series. This
is initial driver and we need additional implementation to support some
functions like power management.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 90593899de.
SAM-BA devices identify themselves CDC-ACM devices and should be using
the cdc-acm driver.
Since commit 5b239f0aeb (USB: cdc-acm: Add pseudo
modem without AT command capabilities) cdc-acm also binds to them.
Note that the Atmel SAM-BA tools expect to use a USB-serial driver and thus
require a symlink from /dev/ttyACMn to some /dev/ttyUSBm (with m < 30) to be
able to select the device. This is simply a UI-issue that should be
fixed by Atmel.
Tested with the SAM-BA 2.10 tools and an Atmel at91sam9260-ek.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Sven Köhler <sven.koehler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The twl4030-usb driver exports the status of VBUS as sysfs attribute.
In case an accessory charger adapter (ACA) is connected to the OTG
transceiver the attribute is always 'off', even when the charger
provides VBUS. Added a variable to keep track of the status of VBUS
and report it correctly
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@tomtom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark ehci_adjust_port_wakeup_flags as __maybe_unused to avoid the following
warning when building the ehci-mxc driver:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-hub.c:130: warning: 'ehci_adjust_port_wakeup_flags' defined but not used
Current ehci-mxc driver implementation does not support suspend/resume.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix warning caused by stray semi-colon at end of macro:
drivers/usb/otg/twl6030-usb.c:183: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hema HK <hemahk@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we don't need Write access then attempt to open backing file in Read Only
mode instead of bailing out too soon.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ep0 request tag was not recorded thus resulting in phase
problems while sending status/response in handle_execption() handler.
This was resulting in MSC compliance test failures with USBCV tool.
With this patch, the Bulk-Only Mass storage RESET request is
handled correctly and the MSC compliance tests pass.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1457) abandons the curious strategy of declaring a
controller dead following hibernation merely in order to reset and
then revive it. The core no longer allow dead controllers to spring
back to life when the system resumes, so there's no reason to declare
a working controller temporarily dead. Instead we do an explicit
reset.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1456) removes all uses of hcd->state from the uhci-hcd
driver, as part of the overall strategy to eliminate hcd->state
completely. Now when a controller dies we call usb_hc_died()
directly, instead of relying on the core interrupt handler to see that
hcd->state has changed to HC_STATE_HALT and make the call for us.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead, make we enter usb/ directory on all
needed cases and enter the subdirectories from
drivers/usb/Makefile.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some bluetooth dongles want ISO mode, and the limited support that the
sl811 offers today is sufficient. So add a Kconfig option for people
to optionally get access to the partial functionality.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1455) removes the extra padding sent by g_file_storage
and g_mass_storage when the gadget wants to send less data than
requested by the host and isn't allowed to halt the bulk-IN endpoint.
Although the Bulk-Only Transport specification requires the padding to
be present, it isn't truly needed since the transfer will be terminated
by a short packet anyway. Furthermore, many existing devices don't
bother to send any padding.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-By: Michal Nazarewicz <mina86@mina86.com>
CC: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The `name' variable is unused in usb_deregister_dev() since commit d6e5bcf
(devfs: Remove the mode field from usb_class_driver as it's no longer needed).
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mass-storage and file-storage gadgets align the length to maximum-packet-size
when preparing the request to receive CBW. This is unnecessary and prevents the
controller driver from knowing that a short-packet is expected.
It is incorrect to set short_not_ok when preparing the request to receive CBW.
CBW will be a short-packet so short_not_ok must not be set.
This makes bh->bulk_out_intended_length unnecessary so it is also removed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we get a port status change event, we need to figure out what type of
port it came from: a USB 3.0 port, or a USB 2.0/1.1 port. We can't know
which usb_hcd to use until that point, so hcd will be NULL for part of the
function. Unfortunately, if any of the sanity checks fail, we'll jump to
the cleanup label before hcd is set to a valid pointer, and then we'll
attempt to tell the USB core to kick the hcd, which is NULL.
Skip kicking the roothub if the sanity checks fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
The logic of the handling Missed Service Error Events was pretty
confusing as we were checking the same condition several times.
In addition, it caused compiler warning since the compiler could
not figure out that event_trb is actually unused in case we are
skipping current TD.
Fix that by rearranging "skip" condition checks, and factor out
skip_isoc_td() so that it is called explicitly.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove 'inline' markings from file-local functions and let compiler
do its job and inline what makes sense for given architecture.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There were some places that compared port_speed == -1 where port_speed
is a u8. This doesn't work unless we cast the -1 to u8. Some places
did it correctly.
Instead of using -1 directly, I've created a DUPLICATE_ENTRY define
which does the cast and is more descriptive as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
This should be queued for kernels back to 2.6.31
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Kill rx tasklet, which is no longer needed, and re-write read processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocate read urbs and read buffers in the same loop during probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to kill ctrl urb on errors as this is done later during close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The drain-delay code is no longer used, so remove it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove driver version and changelog which can be retrieved from git
history.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace dev_dbg with verbose dev_vdbg in read/write paths where
appropriate.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all remaining instances of dbg with dev_dbg.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up some dev_err and dev_dbg messages and make sure that the
appropriate interface device is used for reporting consistently
throughout.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing newline to two dev_dbg and dev_err messages.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous and interrupt SuperSpeed endpoints use the same mechanisms
for decoding bInterval values as HighSpeed ones so adjust the code
accordingly.
Also bandwidth reservation for SuperSpeed matches highspeed, not
low/full speed.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the HcInterrupt register write to clear the
pending interrupt to after the isr work is done, doing this removes
glitches in the irq line.
Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver did not take the zero flag in the USB request. If the
request length is the same as the endpoint's maxpacket, an additional
ZLP with no data has to be transmitted.
The method used here is inspired to what is done in fsl_udc_core.c
(and pxa27x_udc.c and at91_udc.c) where this is supported.
There already was a discussion about this topic with people from
Keymile, and I propose here a better implementation:
http://thread.gmane.org/gmane.linux.usb.general/38951
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial: ftdi_sio: add two missing USB ID's for Hameg interfaces HO720
and HO730
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bind only modem AT command endpoint to option.
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was an unlock missing on the error path.
Also I did a small cleanup by changing ep->dev->lock for just dev->lock.
They're the same lock, but dev->lock is shorter and that's how it is
used for the spin_unlock_irqrestore() call.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Booting latest kernel on my test machine produces a lockdep
warning from the usb_amd_find_chipset_info() function:
WARNING: at /data/lemmy/linux.trees.git/kernel/lockdep.c:2465 lockdep_trace_alloc+0x95/0xc2()
Hardware name: Snook
Modules linked in:
Pid: 959, comm: work_for_cpu Not tainted 2.6.39-rc2+ #22
Call Trace:
[<ffffffff8103c0d4>] warn_slowpath_common+0x80/0x98
[<ffffffff812387e6>] ? T.492+0x24/0x26
[<ffffffff8103c101>] warn_slowpath_null+0x15/0x17
[<ffffffff81068667>] lockdep_trace_alloc+0x95/0xc2
[<ffffffff810ed9ac>] slab_pre_alloc_hook+0x18/0x3b
[<ffffffff810ef227>] kmem_cache_alloc_trace+0x25/0xba
[<ffffffff812387e6>] T.492+0x24/0x26
[<ffffffff81238816>] pci_get_subsys+0x2e/0x73
[<ffffffff8123886c>] pci_get_device+0x11/0x13
[<ffffffff814082a9>] usb_amd_find_chipset_info+0x3f/0x18a
...
It turns out that this function calls pci_get_device under a spin_lock
with irqs disabled, but the pci_get_device function is only allowed in
preemptible context.
This patch fixes the warning by making all data-structure
modifications on temporal storage and commiting this back
into the visible structure at the end. While at it, this
patch also moves the pci_dev_put calls out of the spinlocks
because this function might sleep too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/usb/host/ohci-hcd.c:1028:0:
drivers/usb/host/ohci-au1xxx.c:36:7: warning: "__BIG_ENDIAN" is not defined
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PID 0x0103 for serial port of the OCT DK201 docking station.
Reported-by: Jan Hoogenraad <jan@hoogenraad.net>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build failure introduced by commit
7acc6197b7 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.
CC drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.
Using the cloned skb and freeing the skb in the completion callback
for usb request.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: Christian Simon <simon@swine.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the disconnect function in the composite driver will call spin_lock,
this driver has to call spin_unlock before calling driver->disconnet().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig
Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format build warning and grammar typo on same line.
drivers/usb/host/isp1760-hcd.c:300: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-greg' of git://gitorious.org/usb/usb:
USB: musb: blackfin: work around anomaly 05000450
usb: musb: Fix the crash issue during reboot
usb: musb: gadget: check the correct list_head
usb: musb: temporarily make it bool
USB: musb: dereferencing an iomem pointer
USB: musb: silence printk format warning
USB: musb: using 0 instead of NULL
USB: musb: add missing unlock in cppi_interrupt()
usb: musb: ux500: copy dma mask from platform device to musb device
usb: musb: clear AUTOSET while clearing DMAENAB
DMA mode 1 data corruption anomaly on Blackfin systems. This issue is
specific to the Blackfin silicon as the bug appears to be related to the
connection of the musb ip to the bus/dma fabric.
Data corruption when using USB DMA mode 1. (Issue manager 17-01-0105)
DMA mode 1 allows large size transfers to generate a single interrupt
at the end of the entire transfer. The transfer is split up in packets
of length specified in the Maximum Packet Size field for that endpoint.
If the transfer size is not an integer multiple of the Maximum Packet
Size, a short packet will be present at the end of the transfer.
Under certain conditions this packet may be corrupted in the USB FIFO.
Workaround:
Use DMA mode 1 to transfer (n* Maximum Packet Size) and schedule DMA
mode 0 to transfer the short packet.
As an example if your transfer size is 33168 bytes and Maximum Packet
Size equals 512, schedule [33168 - (33168 mod 512)] in DMA mode 1 and
the remainder (33168 mod 512) in DMA mode 0.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Cc: stable@kernel.org # v2.6.38
Signed-off-by: Felipe Balbi <balbi@ti.com>
"tx_ram" points to io memory. We can't dereference it directly. Sparse
complains about this: "drivers/usb/musb/cppi_dma.c:1205:25: warning:
dereference of noderef expression"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gcc gives the following warnings:
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_tx_segment’:
drivers/usb/musb/cppi_dma.c:600: warning: format ‘%x’ expects type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_rx_segment’:
drivers/usb/musb/cppi_dma.c:822: warning: format ‘%x’ expects type ‘unsigned int’, but argument 9 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_rx_scan’:
drivers/usb/musb/cppi_dma.c:1042: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c:1114: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 7 has type ‘dma_addr_t’
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them
to unsigned long long for printk().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix build warnings caused by removal of *filp arg in struct
usb_serial_driver.
These changes were missed somehow in commits 00a0d0d65b ("tty: remove
filp from the USB tty ioctls") and 60b33c133c ("tiocmget: kill off
the passing of the struct file")
drivers/usb/serial/mct_u232.c:159: warning: initialization from incompatible pointer type
drivers/usb/serial/opticon.c:627: warning: initialization from incompatible pointer type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: cdc-acm: fix potential null-pointer dereference on disconnect
USB: cdc-acm: fix potential null-pointer dereference
USB: cdc-acm: fix memory corruption / panic
USB: Fix 'bad dma' problem on WDM device disconnect
usb: wwan: fix compilation without CONFIG_PM_RUNTIME
USB: uss720 fixup refcount position
usb: musb: blackfin: fix typo in new bfin_musb_vbus_status func
usb: musb: blackfin: fix typo in new dev_pm_ops struct
usb: musb: blackfin: fix typo in platform driver name
usb: musb: Fix for merge issue
ehci-hcd: Bug fix: don't set a QH's Halt bit
USB: Do not pass negative length to snoop_urb()
Fix potential null-pointer exception on disconnect introduced by commit
11ea859d64 (USB: additional power savings
for cdc-acm devices that support remote wakeup).
Only access acm->dev after making sure it is non-null in control urb
completion handler.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Must check return value of tty_port_tty_get.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the WDM class driver a disconnect event leads to calls to
usb_free_coherent to put back two USB DMA buffers allocated earlier.
The call to usb_free_coherent uses a different size parameter
(desc->wMaxCommand) than the corresponding call to usb_alloc_coherent
(desc->bMaxPacketSize0).
When a disconnect event occurs, this leads to 'bad dma' complaints
from usb core because the USB DMA buffer is being pushed back to the
'buffer-2048' pool from which it has not been allocated.
This patch against the most recent linux-2.6 kernel ensures that the
parameters used by usb_alloc_coherent & usb_free_coherent calls in
cdc-wdm.c match.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pm usage counter must be accessed with the proper wrappers
to allow compilation under all configurations.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My testprog do a lot of bitbang - after hours i got following warning and my machine lockups:
WARNING: at /build/buildd/linux-2.6.38/lib/kref.c:34
After debugging uss720 driver i discovered that the completion callback was called before
usb_submit_urb returns. The callback frees the request structure that is krefed on return by
usb_submit_urb.
Signed-off-by: Peter Holik <peter@holik.at>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The common code has a "get" in the middle, but each implementation
does not have it.
Cc: stable@kernel.org
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: stable@kernel.org
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modularization of the Blackfin driver set the name to "musb-blackfin"
in all the boards, but "musb-bfin" in the driver itself. Since the driver
file name uses "blackfin", change the driver to "musb-blackfin". This is
also easier as it's only one file to change.
Cc: stable@kernel.org
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was conflict while merging 2 patches. Enabling vbus code
is wrongly moved to error check if loop.
This is a fix to resolve the merge issue.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1453) fixes a long-standing bug in the ehci-hcd driver.
There is no need to set the Halt bit in the overlay region for an
unlinked or blocked QH. Contrary to what the comment says, setting
the Halt bit does not cause the QH to be patched later; that decision
(made in qh_refresh()) depends only on whether the QH is currently
pointing to a valid qTD. Likewise, setting the Halt bit does not
prevent completions from activating the QH while it is "stopped"; they
are prevented by the fact that qh_completions() temporarily changes
qh->qh_state to QH_STATE_COMPLETING.
On the other hand, there are circumstances in which the QH will be
reactivated _without_ being patched; this happens after an URB beyond
the head of the queue is unlinked. Setting the Halt bit will then
cause the hardware to see the QH with both the Active and Halt bits
set, an invalid combination that will prevent the queue from
advancing and may even crash some controllers.
Apparently the only reason this hasn't been reported before is that
unlinking URBs from the middle of a running queue is quite uncommon.
However Test 17, recently added to the usbtest driver, does exactly
this, and it confirms the presence of the bug.
In short, there is no reason to set the Halt bit for an unlinked or
blocked QH, and there is a very good reason not to set it. Therefore
the code that sets it is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andiry Xu <andiry.xu@amd.com>
CC: David Brownell <david-b@pacbell.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When `echo Y > /sys/module/usbcore/parameters/usbfs_snoop` and
usb_control_msg() returns error, a lot of kernel memory is dumped to dmesg
until unhandled kernel paging request occurs.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This silences warnings such as
drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type
These were added by me in commit 2a79bb1d.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB defines usb_device_type pointing to usb_device_pm_ops that
provides system-wide PM callbacks only and usb_bus_type pointing to
usb_bus_pm_ops that provides runtime PM callbacks only. However,
the USB runtime PM callbacks may be defined in usb_device_pm_ops
which makes it possible to drop usb_bus_pm_ops and will allow us
to consolidate the handling of subsystems by the PM core code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (961 commits)
staging: hv: fix memory leaks
staging: hv: Remove NULL check before kfree
Staging: hv: Get rid of vmbus_child_dev_add()
Staging: hv: Change the signature for vmbus_child_device_register()
Staging: hv: Get rid of vmbus_cleanup() function
Staging: hv: Get rid of vmbus_dev_rm() function
Staging: hv: Change the signature for vmbus_on_isr()
Staging: hv: Eliminate vmbus_event_dpc()
Staging: hv: Get rid of the function vmbus_msg_dpc()
Staging: hv: Change the signature for vmbus_cleanup()
Staging: hv: Simplify root device management
staging: rtl8192e: Don't copy dev pointer to skb
staging: rtl8192e: Pass priv to cmdpkt functions
staging: rtl8192e: Pass priv to firmware download functions
staging: rtl8192e: Pass priv to rtl8192_interrupt
staging: rtl8192e: Pass rtl8192_priv to dm functions
staging: rtl8192e: Pass ieee80211_device to callbacks
staging: rtl8192e: Pass ieee80211_device to callbacks
staging: rtl8192e: Pass ieee80211_device to callbacks
staging: rtl8192e: Pass ieee80211_device to callbacks
...
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
Stop handling gpio-vbus internally. All boards that depended on this
functionality have been converted to use gpio-vbus tranceiver. All
new boards can use it right from the start. Drop unused code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
After redefining CONFIG_PM to depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME) the CONFIG_PM_OPS option is redundant and can be
replaced with CONFIG_PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
A subsequent patch will modify device_set_wakeup_capable() in such
a way that it will call functions which may sleep and therefore it
shouldn't be called under spinlocks. In preparation to that, modify
usb_set_device_state() to avoid calling device_set_wakeup_capable()
under device_state_lock.
Tested-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the Mult and bMaxBurst values from the endpoint companion
descriptor to calculate the max length of an isoc transfer.
Add USB_SS_MULT macro to access Mult field of bmAttributes, at
Sarah's suggestion.
This patch should be queued for the 2.6.36 and 2.6.37 stable trees, since
those were the first kernels to have isochronous support for SuperSpeed
devices.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Use XOR to invert the cycle bit, instead of a more complicated
calculation. Eliminate a check for the link TRB type in find_trb_seg().
We know that there will always be a link TRB at the end of a segment, so
xhci_segment->trbs[TRBS_PER_SEGMENT - 1] will always have a link TRB type.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
When an endpoint stalls, we need to update the xHCI host's internal
dequeue pointer to move it past the stalled transfer. This includes
updating the cycle bit (TRB ownership bit) if we have moved the dequeue
pointer past a link TRB with the toggle cycle bit set.
When we're trying to find the new dequeue segment, find_trb_seg() is
supposed to keep track of whether we've passed any link TRBs with the
toggle cycle bit set. However, this while loop's body
while (cur_seg->trbs > trb ||
&cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
Will never get executed if the ring only contains one segment.
find_trb_seg() will return immediately, without updating the new cycle
bit. Since find_trb_seg() has no idea where in the segment the TD that
stalled was, make the caller, xhci_find_new_dequeue_state(), check for
this special case and update the cycle bit accordingly.
This patch should be queued to kernels all the way back to 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@kernel.org
When an endpoint stalls, the xHCI driver must move the endpoint ring's
dequeue pointer past the stalled transfer. To do that, the driver issues
a Set TR Dequeue Pointer command, which will complete some time later.
Takashi was having issues with USB 1.1 audio devices that stalled, and his
analysis of the code was that the old code would not update the xHCI
driver's ring dequeue pointer after the command completes. However, the
dequeue pointer is set in xhci_find_new_dequeue_state(), just before the
set command is issued to the hardware.
Setting the dequeue pointer before the Set TR Dequeue Pointer command
completes is a dangerous thing to do, since the xHCI hardware can fail the
command. Instead, store the new dequeue pointer in the xhci_virt_ep
structure, and update the ring's dequeue pointer when the Set TR dequeue
pointer command completes.
While we're at it, make sure we can't queue another Set TR Dequeue Command
while the first one is still being processed. This just won't work with
the internal xHCI state code. I'm still not sure if this is the right
thing to do, since we might have a case where a driver queues multiple
URBs to a control ring, one of the URBs Stalls, and then the driver tries
to cancel the second URB. There may be a race condition there where the
xHCI driver might try to issue multiple Set TR Dequeue Pointer commands,
but I would have to think very hard about how the Stop Endpoint and
cancellation code works. Keep the fix simple until when/if we run into
that case.
This patch should be queued to kernels all the way back to 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@kernel.org
USB 3.0 devices have a slightly different suspend sequence than USB
2.0/1.1 devices. There isn't support for USB 3.0 device suspend yet, so
make khubd leave autosuspend disabled for USB 3.0 hubs. Make sure that
USB 3.0 roothubs still have autosuspend enabled, since that path in the
xHCI driver works fine.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB_PORT_STAT_SUPER_SPEED is a made up symbol that the USB core used to
track whether USB ports had a SuperSpeed device attached. This is a
linux-internal symbol that was used when SuperSpeed and non-SuperSpeed
devices would show up under the same xHCI roothub. This particular
port status is never returned by external USB 3.0 hubs. (Instead they
have a USB_PORT_STAT_SPEED_5GBPS that uses a completely different speed
mask.)
Now that the xHCI driver registers two roothubs, USB 3.0 devices will only
show up under USB 3.0 hubs. Rip out USB_PORT_STAT_SUPER_SPEED and replace
it with calls to hub_is_superspeed().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the xHCI host controller is halted, it won't respond to commands
placed on the command ring. So if an URB is cancelled after the first
roothub is deallocated, it will try to place a stop endpoint command on
the command ring, which will fail. The command watchdog timer will fire
after five seconds, and the host controller will be marked as dying, and
all URBs will be completed.
Add a flag to the xHCI's internal state variable for when the host
controller is halted. Immediately return the canceled URB if the host
controller is halted.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Make sure the HCD_FLAG_HW_ACCESSIBLE flag is mirrored by both roothubs,
since it refers to whether the shared hardware is accessible. Make sure
each bus is marked as suspended by setting usb_hcd->state to
HC_STATE_SUSPENDED when the PCI host controller is resumed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a host controller has lost power during a suspend, we must
reinitialize it. Now that the xHCI host has two roothubs, xhci_run() and
xhci_stop() expect to be called with both usb_hcd structures. Be sure
that the re-initialization code in xhci_resume() mirrors the process the
USB PCI probe function uses.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Return early in the roothub control and status functions if the xHCI host
controller is not electrically present in the system (register reads
return all "fs"). This issue only shows up when the xHCI driver registers
two roothubs and the host controller is removed from the system.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB core allocates a USB 2.0 roothub descriptor that has room for 31
(USB_MAXCHILDREN) ports' worth of DeviceRemovable and PortPwrCtrlMask
fields. Limit the number of USB 2.0 roothub ports accordingly. I don't
expect to run into this limitation ever, but this prevents a buffer
overflow issue in the roothub descriptor filling code.
Similarly, a USB 3.0 hub can only have 15 downstream ports, so limit the
USB 3.0 roothub to 15 USB 3.0 ports.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Return the correct xHCI roothub descriptor, based on whether the roothub
is marked as USB 3.0 or USB 2.0 in usb_hcd->bcdUSB. Fill in
DeviceRemovable for the USB 2.0 and USB 3.0 roothub descriptors, using the
Device Removable bit in the port status and control registers. xHCI is
the first host controller to actually properly set these bits (other hosts
say all devices are removable).
When userspace asks for a USB 2.0-style hub descriptor for the USB 3.0
roothub, stall the endpoint. This is what real external USB 3.0 hubs do,
and we don't want to return a descriptor that userspace didn't ask for.
The USB core is already fixed to always ask for USB 3.0-style hub
descriptors. Only usbfs (typically lsusb) will ask for the USB 2.0-style
hub descriptors. This has already been fixed in usbutils version 0.91,
but the kernel needs to deal with older usbutils versions.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch changes the xHCI driver to allocate two roothubs. This touches
the driver initialization and shutdown paths, roothub emulation code, and
port status change event handlers. This is a rather large patch, but it
can't be broken up, or it would break git-bisect.
Make the xHCI driver register its own PCI probe function. This will call
the USB core to create the USB 2.0 roothub, and then create the USB 3.0
roothub. This gets the code for registering a shared roothub out of the
USB core, and allows other HCDs later to decide if and how many shared
roothubs they want to allocate.
Make sure the xHCI's reset method marks the xHCI host controller's primary
roothub as the USB 2.0 roothub. This ensures that the high speed bus will
be processed first when the PCI device is resumed, and any USB 3.0 devices
that have migrated over to high speed will migrate back after being reset.
This ensures that USB persist works with these odd devices.
The reset method will also mark the xHCI USB2 roothub as having an
integrated TT. Like EHCI host controllers with a "rate matching hub" the
xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller.
It doesn't really have a TT, but we'll lie and say it has an integrated
TT. We need to do this because the USB core will reject LS/FS devices
under a HS hub without a TT.
Other details:
-------------
The roothub emulation code is changed to return the correct number of
ports for the two roothubs. For the USB 3.0 roothub, it only reports the
USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS
ports. The code to disable a port now checks the speed of the roothub,
and refuses to disable SuperSpeed ports under the USB 3.0 roothub.
The code for initializing a new device context must be changed to set the
proper roothub port number. Since we've split the xHCI host into two
roothubs, we can't just use the port number in the ancestor hub. Instead,
we loop through the array of hardware port status register speeds and find
the Nth port with a similar speed.
The port status change event handler is updated to figure out whether the
port that reported the change is a USB 3.0 port, or a non-SuperSpeed port.
Once it figures out the port speed, it kicks the proper roothub.
The function to find a slot ID based on the port index is updated to take
into account that the two roothubs will have over-lapping port indexes.
It checks that the virtual device with a matching port index is the same
speed as the passed in roothub.
There's also changes to the driver initialization and shutdown paths:
1. Make sure that the xhci_hcd pointer is shared across the two
usb_hcd structures. The xhci_hcd pointer is allocated and the
registers are mapped in when xhci_pci_setup() is called with the
primary HCD. When xhci_pci_setup() is called with the non-primary
HCD, the xhci_hcd pointer is stored.
2. Make sure to set the sg_tablesize for both usb_hcd structures. Set
the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit
DMA. (The PCI DMA mask is set from the primary HCD further down in
the xhci_pci_setup() function.)
3. Ensure that the host controller doesn't start kicking khubd in
response to port status changes before both usb_hcd structures are
registered. xhci_run() only starts the xHC running once it has been
called with the non-primary roothub. Similarly, the xhci_stop()
function only halts the host controller when it is called with the
non-primary HCD. Then on the second call, it resets and cleans up the
MSI-X irqs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci_find_slot_id_by_port() tries to map the port index to the slot ID for
the USB device. In the future, there will be two xHCI roothubs, and their
port indices will overlap. Therefore, xhci_find_slot_id_by_port() will
need to use information in the roothub's usb_hcd structure to map the port
index and roothub speed to the right slot ID.
Add a new parameter to xhci_find_slot_id_by_port(), in order to pass in
the roothub's usb_hcd structure.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There are several variables in the xhci_hcd structure that are related to
bus suspend and resume state. There are a couple different port status
arrays that are accessed by port index. Move those variables into a
separate structure, xhci_bus_state. Stash that structure in xhci_hcd.
When we have two roothhubs that can be suspended and resumed separately,
we can have two xhci_bus_states, and index into the port arrays in each
structure with the fake roothub port index (not the real hardware port
index).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In the upcoming patches, the roothub emulation code will need to return
port status and port change buffers based on whether they are called with
the xHCI USB 2.0 or USB 3.0 roothub. To facilitate that, make the roothub
code index into an array of port addresses with wIndex, rather than
calculating the address using the offset and the address of the PORTSC
registers. Later we can set the port array to be the array of USB 3.0
port addresses, or the USB 2.0 port addresses, depending on the roothub
passed in.
Create a temporary (statically sized) port array and fill it in with both
USB 3.0 and USB 2.0 port addresses. This is inefficient to do for every
roothub call, but this is needed for git bisect compatibility. The
temporary port array will be deleted in a subsequent patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The hcd->flags are in a sorry state. Some of them are clearly specific to
the particular roothub (HCD_POLL_RH, HCD_POLL_PENDING, and
HCD_WAKEUP_PENDING), but some flags are related to PCI device state
(HCD_HW_ACCESSIBLE and HCD_SAW_IRQ). This is an issue when one PCI device
can have two roothubs that share the same IRQ line and hardware.
Make sure to set HCD_FLAG_SAW_IRQ for both roothubs when an interrupt is
serviced, or an URB is unlinked without an interrupt. (We can't tell if
the host actually serviced an interrupt for a particular bus, but we can
tell it serviced some interrupt.)
HCD_HW_ACCESSIBLE is set once by usb_add_hcd(), which is set for both
roothubs as they are added, so it doesn't need to be modified.
HCD_POLL_RH and HCD_POLL_PENDING are only checked by the USB core, and
they are never set by the xHCI driver, since the roothub never needs to be
polled.
The usb_hcd's state field is a similar mess. Sometimes the state applies
to the underlying hardware: HC_STATE_HALT, HC_STATE_RUNNING, and
HC_STATE_QUIESCING. But sometimes the state refers to the roothub state:
HC_STATE_RESUMING and HC_STATE_SUSPENDED.
Alan Stern recently made the USB core not rely on the hcd->state variable.
Internally, the xHCI driver still checks for HC_STATE_SUSPENDED, so leave
that code in. Remove all references to HC_STATE_HALT, since the xHCI
driver only sets and doesn't test those variables. We still have to set
HC_STATE_RUNNING, since Alan's patch has a bug that means the roothub
won't get registered if we don't set that.
Alan's patch made the USB core check a different variable when trying to
determine whether to suspend a roothub. The xHCI host has a split
roothub, where two buses are registered for one PCI device. Each bus in
the xHCI split roothub can be suspended separately, but both buses must be
suspended before the PCI device can be suspended. Therefore, make sure
that the USB core checks HCD_RH_RUNNING() for both roothubs before
suspending the PCI host.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Introduce the notion of a PCI device that may be associated with more than
one USB host controller driver (struct usb_hcd). This patch is the start
of the work to separate the xHCI host controller into two roothubs: a USB
3.0 roothub with SuperSpeed-only ports, and a USB 2.0 roothub with
HS/FS/LS ports.
One usb_hcd structure is designated to be the "primary HCD", and a pointer
is added to the usb_hcd structure to keep track of that. A new function
call, usb_hcd_is_primary_hcd() is added to check whether the USB hcd is
marked as the primary HCD (or if it is not part of a roothub pair). To
allow the USB core and xHCI driver to access either roothub in a pair, a
"shared_hcd" pointer is added to the usb_hcd structure.
Add a new function, usb_create_shared_hcd(), that does roothub allocation
for paired roothubs. It will act just like usb_create_hcd() did if the
primary_hcd pointer argument is NULL. If it is passed a non-NULL
primary_hcd pointer, it sets usb_hcd->shared_hcd and usb_hcd->primary_hcd
fields. It will also skip the bandwidth_mutex allocation, and set the
secondary hcd's bandwidth_mutex pointer to the primary HCD's mutex.
IRQs are only allocated once for the primary roothub.
Introduce a new usb_hcd driver flag that indicates the host controller
driver wants to create two roothubs. If the HCD_SHARED flag is set, then
the USB core PCI probe methods will allocate a second roothub, and make
sure that second roothub gets freed during rmmod and in initialization
error paths.
When usb_hc_died() is called with the primary HCD, make sure that any
roothubs that share that host controller are also marked as being dead.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver essentially has both a USB 2.0 and a USB 3.0 roothub. So
setting the HCD_USB3 bits in the hcd->driver->flags is a bit misleading.
Add a new field to usb_hcd, bcdUSB. Store the result of
hcd->driver->flags & HCD_MASK in it. Later, when we have the xHCI driver
register the two roothubs, we'll set the usb_hcd->bcdUSB field to HCD_USB2
for the USB 2.0 roothub, and HCD_USB3 for the USB 3.0 roothub.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the bandwith_mutex in struct usb_hcd to a pointer. This will allow
the pointer to be shared across usb_hcds for the upcoming work to split
the xHCI driver roothub into a USB 2.0/1.1 and a USB 3.0 bus.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor out the code in usb_add_hcd() to request the IRQ line for the
HCD. This will only need to be called once for the two xHCI roothubs, so
it's easier to refactor it into a function, rather than wrapping the long
if-else block into another if statement.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Make the labels for the goto statements in usb_hcd_pci_probe()
describe the cleanup they do, rather than being numbered err[1-4].
This makes it easier to add error handling later.
The error handling for this function looks a little fishy, since
set_hs_companion() isn't called until the very end of the function, and
clear_hs_companion() is called if this function fails earlier than that.
But it should be harmless to clear a NULL pointer, so leave the error
handling as-is.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Instead of allocating space for the whole xhci_hcd structure at the end of
usb_hcd, make the USB core allocate enough space for a pointer to the
xhci_hcd structure. This will make it easy to share the xhci_hcd
structure across the two roothubs (the USB 3.0 usb_hcd and the USB 2.0
usb_hcd).
Deallocate the xhci_hcd at PCI remove time, so the hcd_priv will be
deallocated after the usb_hcd is deallocated. We do this by registering a
different PCI remove function that calls the usb_hcd_pci_remove()
function, and then frees the xhci_hcd. usb_hcd_pci_remove() calls
kput() on the usb_hcd structure, which will deallocate the memory that
contains the hcd_priv pointer, but not the memory it points to.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Make sure to call into the USB core's link, unlink, and giveback URB
functions with the usb_hcd pointer found by using urb->dev->bus. This
will avoid confusion later, when the xHCI driver will deal with URBs from
two separate buses (the USB 3.0 roothub and the faked USB 2.0 roothub).
Assume xhci_urb_dequeue() will be called with the proper usb_hcd.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Commit d199c96d by Alan Stern ensured that low speed and full speed
devices below a high speed hub without a transaction translator (TT) would
never get enumerated. Simplify the check for a TT in the xHCI virtual
device allocation to only check if the usb_device references a parent's
TT.
Make sure not to set the TT information on LS/FS devices directly
connected to the roothub. The xHCI host doesn't really have a TT, and the
host will throw an error when those virtual device TT fields are set for a
device connected to the roothub. We need this check because the xHCI
driver will shortly register two roothubs: a USB 2.0 roothub and a USB 3.0
roothub.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Make the USB 3.0 roothub registered by the USB core have a SuperSpeed
Endpoint Companion Descriptor after the interrupt endpoint. All USB 3.0
devices are required to have this, and the USB 3.0 bus specification
(section 10.13.1) says which values the descriptor should have.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In USB 3.0, there are two types of resets: a "hot" port reset and a "warm"
port reset. The hot port reset is always tried first, and involves
sending the reset signaling for a shorter amount of time. But sometimes
devices don't respond to the hot reset, and a "Bigger Hammer" is needed.
External hubs and roothubs will automatically try a warm reset when the
hot reset fails, and they will set a status change bit to indicate when
there is a "BH reset" change. Make sure the USB core clears that port
status change bit, or we'll get lots of status change notifications on the
interrupt endpoint of the USB 3.0 hub.
(Side note: you may be confused why the USB 3.0 spec calls the same type
of reset "warm reset" in some places and "BH reset" in other places. "BH"
reset is supposed to stand for "Big Hammer" reset, but it also stands for
"Brad Hosler". Brad died shortly after the USB 3.0 bus specification was
started, and they decided to name the reset after him. The suggestion was
made shortly before the spec was finalized, so the wording is a bit
inconsistent.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size. Change the USB core's hub descriptor to have a
union for the last fields that differ. Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.
Translate the new version of the hub port status field into the old
version that khubd understands. (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)
Add new code to handle link state change status. Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.
This patch is a modified version of the original patch submitted by John
Youn. It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The USB core will set hcd->state to HC_STATE_RUNNING before calling
xhci_run, so there's no point in setting it twice. The USB core also
doesn't pay attention to HC_STATE_RUNNING on the resume path anymore; it
uses HCD_RH_RUNNING(), which looks at hcd->flags & (1U <<
HCD_FLAG_RH_RUNNING. Therefore, it's safe to remove the state set in
xhci_bus_resume().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We would like to allow host controller drivers to stop using hcd->state.
Unfortunately, some host controller drivers use hcd->state as an
implicit way of telling the core that a controller has died. The
roothub registration functions must assume the host died if hcd->state
equals HC_STATE_HALT.
To facilitate drivers that don't want to set hcd->state to
HC_STATE_RUNNING in their initialization routines, we set the state to
running before calling the host controller's start function.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver doesn't ever test hcd->state for HC_STATE_HALT. The USB
core recently stopped using it internally, so there's no point in setting
it in the driver. We still need to set HC_STATE_RUNNING in order to make
it past the USB core's hcd->state check in register_roothub().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears
Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's
too short and often cause dmesg shows "Host controller not halted, aborting
reset." message when rmmod xhci-hcd.
Modify the time limit to comply with xHCI 1.0 specification and prevents the
warning message showing when remove xhci-hcd.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Set hcd->state = HC_STATE_SUSPENDED if there is a power loss during system
resume or the system is hibernated, otherwise leave it be. The variable
old_state is redundant and made an unreachable code path, so remove it.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xhci_bus_suspend() and xhci_bus_resume() functions are a bit hard to
read, because they have an ambiguously named variable "port". Rename it
to "port_index". Introduce a new temporary variable, "max_ports" that
holds the maximum number of roothub ports the host controller supports.
This will reduce the number of register reads, and make it easy to change
the maximum number of ports when there are two roothubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB core only allows up to 31 (USB_MAXCHILDREN) ports under a roothub.
The xHCI driver keeps track of which ports are suspended, which ports have
a suspend change bit set, and what time the port will be done resuming.
It keeps track of the first two by setting a bit in a u32 variable,
suspended_ports or port_c_suspend. The xHCI driver currently assumes we
can have up to 256 ports under a roothub, so it allocates an array of 8
u32 variables for both suspended_ports and port_c_suspend. It also
allocates a 256-element array to keep track of when the ports will be done
resuming.
Since we can only have 31 roothub ports, we only need to use one u32 for
each of the suspend state and change variables. We simplify the bit math
that's trying to index into those arrays and set the correct bit, if we
assume wIndex never exceeds 30. (wIndex is zero-based after it's
decremented from the value passed in from the USB core.) Finally, we
change the resume_done array to only hold 31 elements.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
The irq enabling code is going to be refactored into a new function, so
clean up some checkpatch errors before moving it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header. include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor. This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.
Remove the bitmap #define and replace instances of it in the host
controller code. Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The test of placing a number of command no-ops on the command ring and
counting the number of no-op events that were generated was only used
during the initial xHCI driver bring up. This test is no longer used, so
delete it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The PM core reacts badly when the return code from usb_runtime_suspend()
is not 0, -EAGAIN, or -EBUSY. The PM core regards this as a fatal error,
and refuses to run anymore PM helper functions. In particular,
usbfs_open() and other usbfs functions will fail because the PM core will
return an error code when usb_autoresume_device() is called. This causes
libusb and/or lsusb to either hang or segfault.
If a USB device cannot suspend for some reason (e.g. a hub doesn't report
it has remote wakeup capabilities), we still want lsusb and other
userspace programs to work. So return -EBUSY, which will fill people's
log files with failed tries, but will ensure userspace still works.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Move the USB_STORAGE_ENE_UB6250 entry so that it stays under the
USB_STORAGE menu.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix ene_ub6250 build: it uses usb_storage driver interfaces, so it
should depend on USB_STORAGE.
ene_ub6250.c:(.text+0x14ff19): undefined reference to `usb_stor_reset_resume'
ene_ub6250.c:(.text+0x14ffb1): undefined reference to `usb_stor_bulk_transfer_buf'
ene_ub6250.c:(.text+0x14ffdd): undefined reference to `usb_stor_bulk_srb'
ene_ub6250.c:(.text+0x14fff1): undefined reference to `usb_stor_bulk_transfer_sg'
ene_ub6250.c:(.text+0x1503dd): undefined reference to `usb_stor_set_xfer_buf'
ene_ub6250.c:(.text+0x15048e): undefined reference to `usb_stor_access_xfer_buf'
ene_ub6250.c:(.text+0x150723): undefined reference to `usb_stor_probe1'
ene_ub6250.c:(.text+0x150795): undefined reference to `usb_stor_probe2'
ene_ub6250.c:(.text+0x1507af): undefined reference to `usb_stor_disconnect'
drivers/built-in.o:(.data+0x10224): undefined reference to `usb_stor_suspend'
drivers/built-in.o:(.data+0x10230): undefined reference to `usb_stor_pre_reset'
drivers/built-in.o:(.data+0x10234): undefined reference to `usb_stor_post_reset'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"buf" gets allocated twice in a row. It's the second allocation which
is correct. The first one should be removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: huajun li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Tegra2 USB controller doesn't properly deal with misaligned DMA
buffers, causing corruption. This is especially prevalent with USB
network adapters, where skbuff alignment is often in the middle of a
4-byte dword.
To avoid this, allocate a temporary buffer for the DMA if the provided
buffer isn't sufficiently aligned.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I picked up a new DAK-780EX(professional digitl reverb/mix system),
which use CH341T chipset to communication with computer on 3/2011
and the CH341T's vendor code is 1a86
Looking up the CH341T's vendor and product id's I see:
1a86 QinHeng Electronics
5523 CH341 in serial mode, usb to serial port converter
CH341T,CH341 are the products of the same company, maybe
have some common hardware, and I test the ch341.c works
well with CH341T
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a laptop I see these errors on (most) resumes:
hub 3-0:1.0: over-current change on port 1
hub 3-0:1.0: over-current change on port 2
Since over-current conditions can disappear quite quickly it's better to
downgrade that message to debug level, recheck for an over-current
condition a little later and only print and over-current condition error
if that condition (still) exists when it's rechecked.
Add similar logic to hub over-current changes. (That code is untested,
as those changes do not occur on this laptop.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following section mismatch warning:
WARNING: drivers/usb/built-in.o(.data+0x74c): Section mismatch in reference from the variable ehci_atmel_driver to the function .init.text:ehci_atmel_drv_probe()
The variable ehci_atmel_driver references
the function __init ehci_atmel_drv_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for the OLIMEX ARM-USB-OCD-H JTAG device (id 15ba:002b)
based on FTDI FT2232H
Signed-off-by: JF Argentino <jf.argentino@free.fr>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On https://bugs.launchpad.net/ubuntu/+source/linux/+bug/636091, one of
the cases reported is a big timeout on option_send_setup, which causes
some side effects as tty_lock is held. Looks like some of ZTE MF626
devices also don't like the RTS/DTR setting in option_send_setup, like
with 4G XS Stick W14. The reporter confirms which this it solves the
long freezes in his system.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Direct access to PMIC register is not safe and will impact battery
charging. New IPC command supported in SCU FW for VBus power control.
USB OTG driver will switch to such commands instead of direct access
to PMIC register for safety and SCU FW will handle the actual work
after got the request(IPC command).
Due to this change, usb driver should wait more time for sync OTGSC
with USBCFG by SCU. Update wait time from 2ms to 5ms.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb portion of this driver can now go into drivers/usb/storage.
This leaves the non-usb portion of the code still in staging.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit ab1666c136 (USB: quirk PLL power down mode)
added code that reads the revision ID from the PCI configuration register while
it's stored by PCI subsystem in the 'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a problem with my previous patch series where there's a great
risk that the kernel will crash when unplugging interrupt devices from
the USB port. These lines must have got missing when I rebased the
patches from the older kernel I was working with to 2.6.37 and 2.6-next:
This fixes a bug where the kernel may crash if you unplug a USB device
that has active interrupt transfers.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hcd->state variable is a disaster. It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes. It's
not protected by any locks. And there's no mechanism to prevent it
from going through an invalid transition.
This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died. Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information. The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).
The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them. Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT. Nevertheless, the new code is a
big improvement over the current code.
The patch makes one other change. The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.
This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
MAINTAINERS: Add Andy Gospodarek as co-maintainer.
r8169: disable ASPM
RxRPC: Fix v1 keys
AF_RXRPC: Handle receiving ACKALL packets
cnic: Fix lost interrupt on bnx2x
cnic: Prevent status block race conditions with hardware
net: dcbnl: check correct ops in dcbnl_ieee_set()
e1000e: disable broken PHY wakeup for ICH10 LOMs, use MAC wakeup instead
igb: fix sparse warning
e1000: fix sparse warning
netfilter: nf_log: avoid oops in (un)bind with invalid nfproto values
dccp: fix oops on Reset after close
ipvs: fix dst_lock locking on dest update
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
bnx2x: update driver version to 1.62.00-6
bnx2x: properly calculate lro_mss
bnx2x: perform statistics "action" before state transition.
bnx2x: properly configure coefficients for MinBW algorithm (NPAR mode).
bnx2x: Fix ethtool -t link test for MF (non-pmf) devices.
bnx2x: Fix nvram test for single port devices.
...
timeout variable is not used anywhere in int write_cmd_usb, remove it
Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
is_iso variable is not used anywhere, remove it
Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver was taking max() of a size_t and u32 which causes complaint
about comparison of different types.
Stumbled on this accidently in my config, never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In wusb_cluster_id_get(), if no zero bits exist in wusb_cluster_id_table,
find_first_zero_bit() returns CLUSTER_IDS.
But it is impossible to detect that the bitmap is full because there
is an off-by-one error in the return value check. It will cause
unexpected memory access by setting bit out of wusb_cluster_id_table
bitmap, and caller will get wrong cluster id.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Build log:
In file included from drivers/usb/host/ehci-hcd.c:1208:
drivers/usb/host/ehci-xilinx-of.c: In function 'ehci_hcd_xilinx_of_probe':
drivers/usb/host/ehci-xilinx-of.c:168: error: implicit declaration of function 'of_address_to_resource'
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ehci and ohci drivers are simplified; Since
UHH and TLL initialization, clock handling are
done by common usbhs core driver, these functionalities
are removed from ehci and ohci drivers.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have names on all memory bases, we can
switch to use platform_get_resource_byname() which
will make it simpler when we move to a setup where
OHCI and EHCI on OMAP play well together.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The EHCI controller in OMAP4 supports a transceiver-less link
mode (TLL mode), similar to the one in OMAP3. On the OMAP4
however, there are an additional set of clocks that need
to be turned on to get this working.
Request and configure these for each port if that port
is connected in TLL mode.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In OMAP3xxx with OTG mode or host only mode, When the device
is inserted after the gadget driver loading the enumeration was not
through. This is because the mentor controller will start sensing the
ID PIN only after setting the session bit.
So after ID-GND, need to set the session bit for mentor to get it
configured as A device.
This is a fix to set the session bit again in ID_GND notification handler.
Tested with OMAP3630Zoom3 platform.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update the last_event variable of otg_transceiver. This will be used in
the musb platform glue driver for runtime idling the device.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch supports the retention and offmode support in the idle path for
musb driver using runtime pm APIs.
This is restricted to support offmode and retention only when device not
connected.When device/cable connected with gadget driver loaded,configured
to no idle/standby which will not allow the core transition to retention
or off.
There is no context save/restore done by hardware for musb in OMAP3
and OMAP4,driver has to take care of saving and restoring the context
during offmode.
Musb has a requirement of configuring sysconfig register to force
idle/standby mode and set the ENFORCE bit in module STANDBY register
for retention and offmode support.
Runtime pm and hwmod frameworks will take care of configuring to force
idle/standby when pm_runtime_put_sync is called and back to no
idle/standby when pm_runeime_get_sync is called.
Compile, boot tested and also tested the retention in the idle path on
OMAP3630Zoom3. And tested the global suspend/resume with offmode enabled.
Usb basic functionality tested on OMAP4430SDP.
There is some problem with idle path offmode in mainline, I could not test
with offmode. But I have tested this patch with resetting the controller
in the idle path when wakeup from retention just to make sure that the
context is lost, and restore path is working fine.
Removed .suspend/.resume fnction pointers and functions because there
is no need of having these functions as all required work is done
at runtime in the driver.
There is no need to call the runtime pm api with glue driver device
as glue layer device is the parent of musb core device, when runtime apis
are called for the child, parent device runtime functionality
will be invoked.
Design overview:
pm_runtime_get_sync: When called with musb core device takes care of
enabling the clock, calling runtime callback function of omap2430 glue
layer, runtime call back of musb driver and configure the musb sysconfig
to no idle/standby
pm_runtime_put: Takes care of calling runtime callback function of omap2430
glue layer, runtime call back of musb driver, Configure the musb sysconfig
to force idle/standby and disable the clock.
During musb driver load: Call pm_runtime_get_sync.
End of musb driver load: Call pm_runtime_put
During gadget driver load: Call pm_runtime_get_sync,
End of gadget driver load: Call pm_runtime_put if there is no device
or cable is connected.
During unload of the gadget driver:Call pm_runtime_get_sync if cable/device
is not connected.
End of the gadget driver unload : pm_runtime_put
During unload of musb driver : Call pm_runtime_get_sync
End of unload: Call pm_runtime_put
On connect of usb cable/device -> transceiver notification(VBUS and ID-GND):
pm_runtime_get_sync only if the gadget driver loaded.
On disconnect of the cable/device -> Disconnect Notification:
pm_runtime_put if the gadget driver is loaded.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For OMAP3 and OMAP4 for offmode and retention support, musb
sysconfig is configured to force idle and standby with ENABLE_FORCE bit
of OTG_FORCESTNDBY set.
And on wakeup configure to no ilde/standby with resetting the ENABLE_FORCE
bit. There is not need to save and restore of this register anymore
so removed omap2430_save_context/omap2430_restore_context functions.
and also removed otg_forcestandby member of musb_context_registers
structure
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit ad1adb89a0
(usb: musb: gadget: do not poke with gadget's list_head)
fixed a bug in musb where it was corrupting the list_head
which is supposed to be used by gadget drivers. While
doing that, I forgot to fix the usage in musb_gadget_dequeue()
method. Fix that.
Reported-by: Pavol Kurina <pavol.kurina@emsys.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure that we check the return value of tty_port_tty_get.
Sometimes it may return NULL and we later dereference that.
The only place here is in kobil_read_int_callback, so fix it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that we check the return value of tty_port_tty_get.
Sometimes it may return NULL and we later dereference that.
There are several places to check. For easier handling,
tty_port_tty_get is moved directly to the palce where needed in
keyspan_pda_rx_interrupt.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove redundant "toggle" member from struct isp1760_qtd, and store toggle
status in struct isp1760_qh only.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace the period calculation for INT packets with something readable. Seems
to fix a rare bug with quickly repeated insertion/removal of several USB
devices simultaneously (hub control INT packets).
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Consolidate printouts to use dev_XXX functions instead of an assortment of
printks and driver specific macros. Remove some unused code snippets and struct
members. Remove some unused function parameters and #defines. Change the
"queue_entry" variable name which has different but related meanings in
different places and use "slot" only.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes the redundant hw_next list pointer from struct isp1760_qtd, removes some
unused #defines, removes redundant "urb" member from struct inter_packet_info.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This helps users with platform-bus-connected isp176xs, big-endian cpu,
and missing byteswapping on the data bus. It does so by collecting all
SW byteswaps in one place and also fixes a bug with non-32-bit io
transfers on this hardware, where payload has to be byteswapped
instead of ptds.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch below removes one to many "n's" in a word..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch below removes one to many "n's" in a word..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is similar to what we already do in cdc-phonet.c in the same
situation. pskb_pull() refuses to work with HIGHMEM, even if it is
known that the socket buffer is entirely in "low" memory.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/usb. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver doesn't know how much data a device is going to send,
the buffer size should be at least as big as the endpoint's maxpacket
value. The serial drivers don't follow this rule; many of them
request only 256-byte bulk-in buffers. As a result, they suffer
overflow errors if a high-speed device wants to send a lot of data,
because high-speed bulk endpoints are required to have a maxpacket
size of 512.
This patch (as1450) fixes the problem by using the driver's
bulk_in_size value as a minimum, always allocating buffers no smaller
than the endpoint's maxpacket size.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Flynn Marquardt <flynn@flynnux.de>
CC: <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
