The SMSC/Microchip LAN9303 is an ethernet switch device with one CPU port
and two external ethernet ports with built-in phys.
This driver uses the DSA framework, but is currently only capable of
separating the two external ports. There is no offload support yet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bad SKB accesses if the SKB was paged, which is the case
for the only driver supporting this - iwlwifi.
-----BEGIN PGP SIGNATURE-----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=r4GR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A single fix, for the MU-MIMO monitor mode, that fixes
bad SKB accesses if the SKB was paged, which is the case
for the only driver supporting this - iwlwifi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 4.8.4 complains that mlx4_SW2HW_MPT_wrapper() uses an uninitialized
'mpt' variable:
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_SW2HW_MPT_wrapper':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2802:12: warning: 'mpt' may be used uninitialized in this function [-Wmaybe-uninitialized]
mpt->mtt = mtt;
I think this warning is a false complaint. mpt is only used when
mr_res_start_move_to() return zero, and in all such cases it initializes
mpt. But apparently gcc cannot see that.
Initialize mpt to avoid the warning.
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.
This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.
This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b95e ("mmc: sdhci: enable tuning for DDR50")
Tested-and-reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
update RF register 47 and 54 values according to vendor driver
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use register values from init LNA function instead of the ones from
restore LNA function. Apply register values based on rx path
configuration.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Somehow AP doesn't come up and the first scan fails if we don't do
VCO calibration every time.
The vendor driver duplicates the VCO calibration function into the
channel switching logic, we can do the same with less duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The base value used for MT7620 differs from Rt5392 which resulted in
quite bad RX signal quality. Fix this by using the correct base value as
well as the LNA calibration values for HT20.
Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.
Commit 60a2218698 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).
This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.
Cc: stable@vger.kernel.org
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ath.git patches for 4.12. Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
* Heavy work for the A000 device series;
* Some cleanup patches;
* A few fixes;
* Dynamic SAR support;
* Geographical SAR support;
* Support a few new PCI device IDs;
-----BEGIN PGP SIGNATURE-----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=ooBi
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-04-19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Another series of patches intended for v4.12. These are the changes:
* Heavy work for the A000 device series;
* Some cleanup patches;
* A few fixes;
* Dynamic SAR support;
* Geographical SAR support;
* Support a few new PCI device IDs;
When wifi is under scanning/linking/roaming, do not run the reset of the
coex mechanism because these activities are important for wifi, just run
the linking process and return.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For bt profiling, we do not need to limit the rx agg size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Using macro to control the bt threshold.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check the bt rssi first and decrease it if the bt rssi is too high.
Then set the tdma and coex table.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use h2c to tell the firmware if the number of AP is more than 10 or
not.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here we monitor one more wifi rssi to check the status of the network
and set the coex table instead of the legacy way.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For p2p/miracast, the wifi may have multiple ports for different roles.
Under this, we need extra settings for turning off the tdma and proper
coex table parameters.
We monnitor the number of links on a port to determine if it is for
p2p/miracast or not.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor the rssi state to set the tdma and limit rx aggregation size to
fit the bt profiling.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix some ident and naming for linux coding style.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For bt a2dp, we need to check more rssi state combinations to have
better voice quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Let the wifi use main antenna to have higher power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The threshold is used to adjust the base line for the rssi state.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use software dac swing and double check if it is sco_only to set the
tdma for voice quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Add more cases to adjust the wifi duration and add a case with
the max interval of 3 for some future uses.
2. rename tdma_adj -> ps_tdma_du_adj to indicate that this member is
for power saving tdma duration adjustment
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dac swing level should be an unsigned 32-bit value rather than
boolean.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Depending on the state of wifi, we need to set different tdma and coex
table parameters to make wfi and bt coexist smoothly. Otherwise the
bt may have low sound quality or mouse lag, which mean bad user
experience. The same problem may occur on wifi also, if could disconnect
or lose some important packets.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the wifi or bt has low rssi, they need extra parameter settings for
the tdma.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tune the wifi/bt slot time to get better performance.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register 0xcb4 determines if the PTA circuit can control the swtich
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of just setting the coex table directly, we check if the
wifi is under some important activity (scanning|roaming|linking) and
mark the packets as high priority in that case.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wifi is at 5G band, it does not intefere with 2.4G bt signal,
hence we can just ignore it and transmit normally as nothing happened.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor wifi status and check if it is changed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gather multiple coex table settings into a function coex_table_with_type()
and control the coex table according the type value as put in
switch-case expression.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The power_save_state function checks the state of power saving.
For tdma settings, the wifi sends nullfunc to pretend enter power saving
and then bt can transmit. Hence the coex needs to check the power status
before set the pstdma function.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally we only increase/decrease bt power in a fixed power gap, this
patch makes us be able to modify bt power for multiple power gaps and we
can precisely adjust the bt power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function updates the information of bt profiling to help us decide
the network status and dispatch the resource properly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are a lot of low-rate packets, then the connection of wifi is
unstable. If so, we should switch resource to bt to have a higher
transmission quality, or wifi resource will be wasted
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We monitor the packet counter to guess if the bt is slave or not, and
when bt is slave, it may receive packet at any time, so we will have to
take care about it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larger packets have higher opportunity to be interrupt by bt signal.
In order to shorten the transmission time, control the packet
aggregation size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
His email is bouncing, and he'd like to use this new one.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'chan_stats' is (re)allocated in _mwifiex_fw_dpc() ->
mwifiex_init_channel_scan_gap(), which is called whenever the device is
initialized -- at probe or at reset.
But we only free it in we completely unregister the adapter, meaning we
leak a copy of it during every reset.
Let's free it in the shutdown / removal paths instead (and in the
error-handling path), to avoid the leak.
Ideally, we can eventually unify much of mwifiex_shutdown_sw() and
mwifiex_remove_card() (way too much copy-and-paste) to reduce the burden
on bugfixes like this. But that's work for tomorrow.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we shut down the device (i.e., during 'reset'), we cancel any
outstanding work, but we don't clear any work-related flags. This can
cause problems if, e.g., we begin to queue a new firmware dump or card
reset while the other one is in progress. That might leave work_flags
with a stale value, and we might begin one of these *after* we've
completely reset the device. That doesn't make sense, because all
firmware context will have been lost by then.
This fixes some forms of cascading failures, where I:
(a) force a firmware dump (cat /sys/kernel/debug/mwifiex/mlan0/device_dump)
(b) run a Wifi scan in parallel (iw mlan0 scan)
(c) the scan times out due to (a) hogging the interface
(d) the command timeout triggers another firmware dump and a reset [*]
(e) the 2nd firmware dump flag persists across the reset
(f) as soon as the interface comes back up, we trigger the pending
firmware dump
(g) subsequent commands time out again, while we are processing the
firmware dump; return to (d)
[*] Note that automatic card_reset() support is not yet implemented for
the mwifiex PCIe driver, so we won't hit *exactly* this behavior yet.
But we can see similarly-confusing behaviors today.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we reset because of a command timeout, we should reset this flag.
Otherwise, we might erroneously think the next command after reset is
timing out, and trigger another reset.
The above behavior effectively neuters the automatic card_reset()
behavior, as it means we will never recover from a command timeout
properly (and in fact, we might enter an infinite loop:
timeout -> reset -> (fake) timeout -> reset -> ...
This fixes a bug introduced with introduction of PCIe function level
reset support, but it was carried into the SDIO driver when it was
converted to use the same codepaths. And this is currently mostly a
problem only in the SDIO driver, because it's the only one with
automatic card_reset() support (e.g., on command timeout). But it will
be a problem for PCIe too, as I'm working on supporting automatic
card_reset() for PCIe.
Fixes: c742e623e9 ("mwifiex: sdio card reset enhancement")
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
