Implements standby support for Kirkwood SoC. When the SoC enters
standby state the memory PM units are disabled, the DDR is set
in self-refresh mode, and the CPU is set in WFI.
At this point there's no clock gating, as that is considered each
driver's task.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
This commit replaces the legacy MBus initialization with the new
DT-based in Kirkwood. For boards that are not yet converted to DT,
we keep the legacy initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the introduction of the ID based MBus API, it's better
to switch to use it instead of the current name based scheme.
This will allow to deprecate the name based API, once every
user is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
These really should be a single driver because they're fully integrated
in hardware. Make them so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpP1WAAoJEAi3KVZQDZAeItIH/1QVHhqYSpOnXGu4zQHswvIM
SRQoy4hiCJm+yywTnIDJPMQdBKD1vURRRdGWQouNsFoBaHki4v2BBxfBNFoDN+rx
VtECH7F1SbJ/Pb7XLVnswqRXVNqrY5fOY5mW42ALFBT9VxcKoD1FyqCaXfaU9JA4
VQCzR7DjFhr8bppZknQ5ZT/qI66Wj1oNiJtBdItmxT0pVfElvAOV6FHzfMGrrDrM
+v8T8KdFIdmH1Ny5J5KLQSE9qBLqae0vlDNgsfwfh1DY/Lye3rDHqPDKrh7YZjHR
xNc6JU+zEdP3tK1f1jgmjn/giY7HqpAFm46p9k/pF9gsE5SE0L/e0Dh9apOcq24=
=qUyf
-----END PGP SIGNATURE-----
Merge tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: convert db-88f6281/db-88f6282 to the Device Tree
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
arm: kirkwood: move PCIe window init to legacy driver
pci: mvebu: enable driver usage on Kirkwood
- kirkwood
- use the cpufreq driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRplfXAAoJEAi3KVZQDZAeOtIH/R2D0Bkb7xfhxKYDUg3jrMbz
YZz2RYVqKJQHj5xo/Yt4F6NS9WqqKRYWEzJQTH4a2EfSC/zfLM3QTG46N71VojPn
K/eigw1jeQ8qrDIQhd3mAGh4VzW2Q4xOuFWbWzH0RUgZZxAEQyyh2LcEftxTwSlK
nHWLhBY+t4hBIZQ6oCt1byRrcbxScoABb6joJVJxV1H20FB9TyzWQXgrJs1qGWNW
yKzKC5WWBNtEmaMLGDkDy65nAVOsiO1M+f30Oo4sKfYjDe5CosTS4asdg1toupVT
lJq6rskzIN503uUC6SFcNcPqHc9nJoHs7T8aTtFMf05wXxC0kdUvZoYeDVUyt+M=
=3/Kd
-----END PGP SIGNATURE-----
Merge tag 'soc-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper, mvebu soc changes for v3.11
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'soc-3.11-2' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: Instantiate cpufreq driver
arm: kirkwood: use the default of match table
Register a platform driver structure for the cpufreq driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since we are going to enable the usage of the mvebu PCIe driver on
Kirkwood, we don't want the PCIe windows to be unconditionally created
by kirkwood_setup_wins(). Therefore, we move the PCIe window
initialization into the legacy PCIe driver
(arch/arm/mach-kirkwood/pcie.c).
The platforms using the legacy driver will see their windows
statically allocated by
arch/arm/mach-kirkwood/pcie.c:kirkwood_pcie_init(). The platforms
using the new driver in drivers/pci/ will see their windows
dynamically allocated directly by the driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch:
387870f mm: dmapool: use provided gfp flags for all dma_alloc_coherent() calls
makes these calls on Kirkwood and Orion5x redundant. The drivers are
not making atomic requests for coherent memory and hence the default
pool size is now sufficient.
Jason Cooper added mach-mvebu/ hunk, and corrected minor typos in commit
message.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit migrates the mach-kirkwood platforms to use the mvebu-mbus
driver and therefore removes the Kirkwood-specific addr-map code.
The kirkwood_init_early() function is now responsible for initializing
the mvebu-mbus driver by calling mvebu_mbus_init().
The address decoding windows are now registered in the
kirkwood_setup_wins() function. It is worth noting that the four PCIe
address decoding windows will ultimately no longer have to be
registered here: it will be done automatically by the PCIe driver once
Kirkwood has been migrated to use the upcoming mvebu PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRCqOnAAoJEAi3KVZQDZAewlUH/04tpMdf2rvgNP8uUVPVx62T
cXMga9qLTyXQ9hn31KP7fd/JPLRJFsG/+jy4x687EurJGIXXaWGNadjlE69DEPAZ
jt78sPa+Mo/xYD4XoNCr/ng1cbnTwc1ebSRSfN+nIjWynE8Do7tkOKxfJodTgQCM
XbE3EHfvAktKfJTsFDPsFwoIycEYxFsN4jQPwiCdPHVb24py3FWBy+qep7wtLfSO
gTnakEcOsQc7aFzrFdZ1ZnQ9KRlBYXVN636o4sQkM+UM9Vf7FAWBM4OCi2KP4trU
IlTzknoMAMYat+AtYzq1FcDmajeP/EgG6DbQh7lqUK0LEILn2rdAUlgN2QB3VIs=
=6oef
-----END PGP SIGNATURE-----
Merge tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu drivers for v3.9
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
* tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
cpuidle: kirkwood: Move out of mach directory
rtc: Add support of rtc-mv for MVEBU SoCs
ARM: Kirkwood: Support basic hotplug for PCI-E
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and
into drivers/cpuidle. Convert the driver into a platform driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a branch with updates for Marvell's mvebu/kirkwood platforms. They
came in late-ish, and were heavily interdependent such that it didn't
make sense to split them up across the cross-platform topic branches. So
here they are (for the second release in a row) in a branch on their own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7luC
-----END PGP SIGNATURE-----
Merge tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
mv64xxx_of_config requires that the tclk frequency be found
through the clk stuff rather than through device tree, so add
another override for the 2nd controller.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since we got rid of the per-XOR channel 'mv_xor' driver, now the
per-XOR engine driver that used to be called 'mv_xor_shared' can
simply be named 'mv_xor'.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Mostly printk to pr_{err|info} changes and a few strings split over
multiple lines are combined.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Mostly missing statics, but also missing include files
and void parameters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the CACHE_FEROCEON_L2 test to kirkwood_l2_init, since linking
fails on the reference to feroceon_l2_init.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* 'kirkwood/addr_decode' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add address decoding controller to the DT
arm: mvebu: add basic address decoding support to Armada 370/XP
arm: plat-orion: make bridge_virt_base non-const to support DT use case
arm: plat-orion: introduce PLAT_ORION_LEGACY hidden config option
arm: plat-orion: use void __iomem pointers for addr-map functions
arm: plat-orion: use void __iomem pointers for time functions
arm: plat-orion: use void __iomem pointers for MPP functions
arm: plat-orion: use void __iomem pointers for UART registration functions
arm: mach-mvebu: use IOMEM() for base address definitions
arm: mach-orion5x: use IOMEM() for base address definitions
arm: mach-mv78xx0: use IOMEM() for base address definitions
arm: mach-kirkwood: use IOMEM() for base address definitions
arm: mach-dove: use IOMEM() for base address definitions
arm: mach-orion5x: use plus instead of or for address definitions
arm: mach-mv78xx0: use plus instead of or for address definitions
arm: mach-kirkwood: use plus instead of or for address definitions
arm: mach-dove: use plus instead of or for address definitions
This branch had quite a few conflicts, in particular with the PCI static
map rework from Rob Herring, and a few other context conflicts due to
changes in Kconfig, etc.
I fixed up conflicts in:
arch/arm/Kconfig
arch/arm/mach-dove/common.c
arch/arm/mach-dove/include/mach/dove.h
arch/arm/mach-kirkwood/common.c
arch/arm/mach-kirkwood/include/mach/kirkwood.h
arch/arm/mach-mv78xx0/common.c
arch/arm/mach-mv78xx0/include/mach/mv78xx0.h
arch/arm/mach-orion5x/common.c
arch/arm/mach-orion5x/include/mach/orion5x.h
Signed-off-by: Olof Johansson <olof@lixom.net>
The functions for time management now take void __iomem pointers, so
we remove the temporary "unsigned long" casts from the mach-*/common.c
files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The registration functions for UARTs now take void __iomem pointers,
so we remove the temporary "unsigned long" casts from the
mach-*/common.c files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We now define all virtual base address constants using IOMEM() so that
those are naturally typed as void __iomem pointers, and we do the
necessary adjustements in the mach-kirkwood code.
Note that we introduce a few temporary additional "unsigned long"
casts when calling into plat-orion functions. Those are removed by
followup patches converting plat-orion functions to void __iomem
pointers as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=utuw
-----END PGP SIGNATURE-----
Merge tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
The default 256 KiB coherent pool may be too small for some of the Kirkwood
devices, so increase it to make sure that devices will be able to allocate
their buffers with GFP_ATOMIC flag.
Suggested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The mv643xx ethernet controller limits the packet size for the TX
checksum offloading. This patch sets this limits for Kirkwood and
Dove which have smaller limits that the default.
As a side note, this patch is an updated version of a patch sent some years
ago: http://lists.infradead.org/pipermail/linux-arm-kernel/2010-June/017320.html
which seems to have been lost.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: <stable@vger.kernel.org>
From Rob Herring <robherring2@gmail.com>:
This is the 2nd part of mach/io.h removals. This series removes io.h on
platforms with PCI by creating a fixed virtual I/O mapping and a common
__io() macro.
This version has changed a bit to accommodate Tegra converting its PCIe
host to a platform driver. Now the virtual space is only reserved during
early boot before .map_io() is called. The mapping is not created until
calling pci_ioremap_io which can be done at any point after vmalloc is
initialized.
I've gone back to fixed 64K windows for each PCI bus. This allows
removing all the i/o resource setup from the individually platforms and
placing it within the common ARM PCI code.
I've only tested versatilepb under qemu (with the model hacked up to
actually enable i/o space), so any testing is appreciated. iop3xx and
mv78xx0 have some risk of breaking as the PCI bus addresses are moved
to 0 from matching the cpu host bus addesss.
* cleanup/io-pci:
ARM: iop3xx: use fixed PCI i/o mapping
ARM: mv78xx0: use fixed pci i/o mapping
ARM: iop13xx: use fixed PCI i/o mapping
iop13xx: use more regular PCI I/O space handling
ARM: orion5x: use fixed PCI i/o mapping
ARM: kirkwood: use fixed PCI i/o mapping
ARM: dove: use fixed PCI i/o mapping
ARM: footbridge: use fixed PCI i/o mapping
ARM: shark: use fixed PCI i/o mapping
ARM: integrator: remove trailing whitespace on pci_v3.c
ARM: integrator: use fixed PCI i/o mapping
ARM: tegra: use fixed PCI i/o mapping
ARM: versatile: use fixed PCI i/o mapping
ARM: move PCI i/o resource setup into common code
ARM: Add fixed PCI i/o mapping
i2c: iop3xx: use standard gpiolib functions
i2c: iop3xx: clean-up trailing whitespace
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Conflicts:
arch/arm/mach-kirkwood/common.c
Move kirkwood PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Commit 98d9986 (ARM: Kirkwood: Replace clock gating) and the fix 5fb2ce
(ARM: Kirkwood: clk_register_gate_fn: add fn assignment) introduced a custom
variant of clock gating which allows to define a function to be called
before gating the clock off.
This is used to disable the SATA and PCIe PHYs if the respective clocks
are unused after initialization.
However, of these two drivers, the SATA driver may be compiled as a module.
The driver re-enables the clocks at module init but the PHYs stay disabled.
Since the custom clock gating disabled the PHYs when gating the clock off,
it should also re-enable them when enabling the clock gate. This is done by
adding a second function that may be used to enable the PHYs.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Marvell engineers tell us:
It seems that many units use the RUNIT clock.
SPI, UART, NAND, TWSI, ...
So it's not possible to clock gate it.
Currently the SPI, NAND and TWSI driver will clk_prepaure_enable()
this clk, but since we have no idea what ... is, and turning this clk
off results in a hard lock, unconditionally enable runit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
In commit:
98d9986 ARM: Kirkwood: Replace clock gating
the kirkwood clock gating has been reworked. A custom variant of
clock gating, that calls a custom function before gating the clock
off, has been introduced. However in clk_register_gate_fn() this
custom function "fn" is never assigned.
This patch adds the missing fn assignment.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
When the ethernet driver was built as a module, it would lock the
machine when loaded. At boot the ethernet clks are unused, so get
turned off. Later, when the module is loaded, the probe function
would access the hardware before the clock was restarted, and the
machine would lock. It has also been determined that when the clk is
turned off, the interface forgets its MAC address, which for most
systems, is set by the boot loader.
When the machine setup file creates a platform device for the
interface, prepare and enable the clock for the interface. This will
ensure it is not turned off. However, if the setup file only
instantiates one platform device, the other will have its clk
disabled, thus maybe saving a little power.
Report-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a varient of the basic clk-gate code. This variant calls a
function before gating the clock off. This function is used to disable
the SATA or PCIe PHY.
Now that all the drivers prepare and enable there clk as needed, there
is no need for the common code to keep track of which clocks need
gating on. Let the common clock framework turn off clocks which are
not used.
Buy using the added clk varient, when the clk framework turns off SATA
or PCIe clocks, we also disabled SATA and PCIe PHYs which were not
needed.
The function kirkwood_pcie_id() can now be called outside of __init
code, so remove this property for it, and functions it calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Prepare and enable the clocks when the board indicates the pcie buses
will be used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion platforms can gate the XOR driver clock. If the clock
exisits, unable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion platforms support gating of the clock. If the clock exists
enable/disbale it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion devices can gate the SDIO clock. If the clock exists,
enable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Not all orion platforms can gate the clock, but if it does exist,
enable/disable it as appropriate.
v2: Fix the name of the clkdev entry.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Not all platforms support gating the clock, so it is not an error if
the clock does not exist. However, if it does exist, we should
enable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Orion kirkwood chips have a gatable clock per SATA channel. Add
code to get and enable this clk if it exists.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Let the machine pass to the platform which clock is used by the uart.
Enable the clock and use clk_get_rate() to determine its rate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
