The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to propagate static FDB entries and certain bridge
port attributes (e.g. learning, flooding) down to the port netdev
driver when bridge port is a VLAN interface.
Achieve that by setting ndo_bridge* and ndo_fdb* in vlan_netdev_ops to
the corresponding switchdev_port* functions. This is consistent with
team and bond devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports. The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.
With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC drivers mark device as detached during error recovery.
It expects no manangement hooks to be invoked in this state.
Invoke driver vlan hooks only if device is present.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan notifier handler will try to update all vlans
for a device when that device comes up. A problem occurs,
however, when the vlan device was set to promiscuous, but not
by the user (ex: a bridge). In that case, dev->gflags are
not updated. What results is that the lower device ends
up with an extra promiscuity count. Here are the
backtraces that prove this:
[62852.052179] [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.052186] [<ffffffff8160bcbb>] ? _raw_spin_unlock_bh+0x1b/0x40
[62852.052188] [<ffffffff814fe4be>] ? dev_set_rx_mode+0x2e/0x40
[62852.052190] [<ffffffff814fe694>] dev_set_promiscuity+0x24/0x50
[62852.052194] [<ffffffffa0324795>] vlan_dev_open+0xd5/0x1f0 [8021q]
[62852.052196] [<ffffffff814fe58f>] __dev_open+0xbf/0x140
[62852.052198] [<ffffffff814fe88d>] __dev_change_flags+0x9d/0x170
[62852.052200] [<ffffffff814fe989>] dev_change_flags+0x29/0x60
The above comes from the setting the vlan device to IFF_UP state.
[62852.053569] [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.053571] [<ffffffffa032459b>] ? vlan_dev_set_rx_mode+0x2b/0x30
[8021q]
[62852.053573] [<ffffffff814fe8d5>] __dev_change_flags+0xe5/0x170
[62852.053645] [<ffffffff814fe989>] dev_change_flags+0x29/0x60
[62852.053647] [<ffffffffa032334a>] vlan_device_event+0x18a/0x690
[8021q]
[62852.053649] [<ffffffff8161036c>] notifier_call_chain+0x4c/0x70
[62852.053651] [<ffffffff8109d456>] raw_notifier_call_chain+0x16/0x20
[62852.053653] [<ffffffff814f744d>] call_netdevice_notifiers+0x2d/0x60
[62852.053654] [<ffffffff814fe1a3>] __dev_notify_flags+0x33/0xa0
[62852.053656] [<ffffffff814fe9b2>] dev_change_flags+0x52/0x60
[62852.053657] [<ffffffff8150cd57>] do_setlink+0x397/0xa40
And this one comes from the notification code. What we end
up with is a vlan with promiscuity count of 1 and and a physical
device with a promiscuity count of 2. They should both have
a count 1.
To resolve this issue, vlan code can use dev_get_flags() api
which correctly masks promiscuity and allmulti flags.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stacked vlan devices curretly have few features (GRO, HIGHDMA, LLTX).
Since we have software fallbacks in case the NIC can not handle some
features for multiple vlans, we can add the same features as the lower
vlan devices for stacked vlan devices.
This allows stacked vlan devices to create large (GSO) packets and not to
segment packets. Those packets will be segmented by software on the real
device, or even can be segmented by the NIC once TSO for multiple vlans
becomes enabled by the following patches.
The exception is those related to FCoE, which does not have a software
fallback.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a networking device is taken down that has a non-trivial number
of VLAN devices configured under it, we eat a full synchronize_net()
for every such VLAN device.
This is because of the call chain:
NETDEV_DOWN notifier
--> vlan_device_event()
--> dev_change_flags()
--> __dev_change_flags()
--> __dev_close()
--> __dev_close_many()
--> dev_deactivate_many()
--> synchronize_net()
This is kind of rediculous because we already have infrastructure for
batching doing operation X to a list of net devices so that we only
incur one sync.
So make use of that by exporting dev_close_many() and adjusting it's
interfaace so that the caller can fully manage the batch list. Use
this in vlan_device_event() and all the overhead goes away.
Reported-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the real device can segment packets by software, a vlan device
can set TSO/UFO even when the real device doesn't have those features.
Unlike GSO, this allows packets to be segmented after Qdisc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a6111d3c "vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device"
intended to enable hardware time stamping on VLAN interfaces, but
passing SIOCSHWTSTAMP is only half of the story. This patch adds
the second half, by letting user space find out the time stamping
capabilities of the device backing a VLAN interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always returns the same skb it gets, so change to void.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel. When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets. This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.
There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver. These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb. When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.
The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued. The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0
This connection finally times out.
I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver. There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.
The patch attempt to fix this another way. It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core. This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.
CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, vlan will create /proc/net/vlan/<dev>, so when we
create dev with name "config", it will confict with
/proc/net/vlan/config.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows applications to enable hardware timestamping without being aware
of it being a vlan device and figuring out the real device.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When combining real_dev's features and vlan_features, simple
bitwise AND is used. This doesn't work well for checksum
offloading features as if one set has NETIF_F_HW_CSUM and the
other NETIF_F_IP_CSUM and/or NETIF_F_IPV6_CSUM, we end up with
no checksum offloading. However, from the logical point of view
(how can_checksum_protocol() works), NETIF_F_HW_CSUM contains
the functionality of NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM so
that the result should be IP/IPV6.
Add helper function netdev_intersect_features() implementing
this logic and use it in vlan_dev_fix_features().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dc8eaaa006.
vlan: Fix lockdep warning when vlan dev handle notification
Instead we use the new new API to find the lock subclass of
our vlan device. This way we can support configurations where
vlans are interspersed with other devices:
bond -> vlan -> macvlan -> vlan
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if allocating memory for vlan_pcpu_stats failed, the device can not be operated
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I open the LOCKDEP config and run these steps:
modprobe 8021q
vconfig add eth2 20
vconfig add eth2.20 30
ifconfig eth2 xx.xx.xx.xx
then the Call Trace happened:
[32524.386288] =============================================
[32524.386293] [ INFO: possible recursive locking detected ]
[32524.386298] 3.14.0-rc2-0.7-default+ #35 Tainted: G O
[32524.386302] ---------------------------------------------
[32524.386306] ifconfig/3103 is trying to acquire lock:
[32524.386310] (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386326]
[32524.386326] but task is already holding lock:
[32524.386330] (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386341]
[32524.386341] other info that might help us debug this:
[32524.386345] Possible unsafe locking scenario:
[32524.386345]
[32524.386350] CPU0
[32524.386352] ----
[32524.386354] lock(&vlan_netdev_addr_lock_key/1);
[32524.386359] lock(&vlan_netdev_addr_lock_key/1);
[32524.386364]
[32524.386364] *** DEADLOCK ***
[32524.386364]
[32524.386368] May be due to missing lock nesting notation
[32524.386368]
[32524.386373] 2 locks held by ifconfig/3103:
[32524.386376] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff81431d42>] rtnl_lock+0x12/0x20
[32524.386387] #1: (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386398]
[32524.386398] stack backtrace:
[32524.386403] CPU: 1 PID: 3103 Comm: ifconfig Tainted: G O 3.14.0-rc2-0.7-default+ #35
[32524.386409] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[32524.386414] ffffffff81ffae40 ffff8800d9625ae8 ffffffff814f68a2 ffff8800d9625bc8
[32524.386421] ffffffff810a35fb ffff8800d8a8d9d0 00000000d9625b28 ffff8800d8a8e5d0
[32524.386428] 000003cc00000000 0000000000000002 ffff8800d8a8e5f8 0000000000000000
[32524.386435] Call Trace:
[32524.386441] [<ffffffff814f68a2>] dump_stack+0x6a/0x78
[32524.386448] [<ffffffff810a35fb>] __lock_acquire+0x7ab/0x1940
[32524.386454] [<ffffffff810a323a>] ? __lock_acquire+0x3ea/0x1940
[32524.386459] [<ffffffff810a4874>] lock_acquire+0xe4/0x110
[32524.386464] [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386471] [<ffffffff814fc07a>] _raw_spin_lock_nested+0x2a/0x40
[32524.386476] [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386481] [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386489] [<ffffffffa0500cab>] vlan_dev_set_rx_mode+0x2b/0x50 [8021q]
[32524.386495] [<ffffffff8141addf>] __dev_set_rx_mode+0x5f/0xb0
[32524.386500] [<ffffffff8141af8b>] dev_set_rx_mode+0x2b/0x40
[32524.386506] [<ffffffff8141b3cf>] __dev_open+0xef/0x150
[32524.386511] [<ffffffff8141b177>] __dev_change_flags+0xa7/0x190
[32524.386516] [<ffffffff8141b292>] dev_change_flags+0x32/0x80
[32524.386524] [<ffffffff8149ca56>] devinet_ioctl+0x7d6/0x830
[32524.386532] [<ffffffff81437b0b>] ? dev_ioctl+0x34b/0x660
[32524.386540] [<ffffffff814a05b0>] inet_ioctl+0x80/0xa0
[32524.386550] [<ffffffff8140199d>] sock_do_ioctl+0x2d/0x60
[32524.386558] [<ffffffff81401a52>] sock_ioctl+0x82/0x2a0
[32524.386568] [<ffffffff811a7123>] do_vfs_ioctl+0x93/0x590
[32524.386578] [<ffffffff811b2705>] ? rcu_read_lock_held+0x45/0x50
[32524.386586] [<ffffffff811b39e5>] ? __fget_light+0x105/0x110
[32524.386594] [<ffffffff811a76b1>] SyS_ioctl+0x91/0xb0
[32524.386604] [<ffffffff815057e2>] system_call_fastpath+0x16/0x1b
========================================================================
The reason is that all of the addr_lock_key for vlan dev have the same class,
so if we change the status for vlan dev, the vlan dev and its real dev will
hold the same class of addr_lock_key together, so the warning happened.
we should distinguish the lock depth for vlan dev and its real dev.
v1->v2: Convert the vlan_netdev_addr_lock_key to an array of eight elements, which
could support to add 8 vlan id on a same vlan dev, I think it is enough for current
scene, because a netdev's name is limited to IFNAMSIZ which could not hold 8 vlan id,
and the vlan dev would not meet the same class key with its real dev.
The new function vlan_dev_get_lockdep_subkey() will return the subkey and make the vlan
dev could get a suitable class key.
v2->v3: According David's suggestion, I use the subclass to distinguish the lock key for vlan dev
and its real dev, but it make no sense, because the difference for subclass in the
lock_class_key doesn't mean that the difference class for lock_key, so I use lock_depth
to distinguish the different depth for every vlan dev, the same depth of the vlan dev
could have the same lock_class_key, I import the MAX_LOCK_DEPTH from the include/linux/sched.h,
I think it is enough here, the lockdep should never exceed that value.
v3->v4: Add a huge array of locking keys will waste static kernel memory and is not a appropriate method,
we could use _nested() variants to fix the problem, calculate the depth for every vlan dev,
and use the depth as the subclass for addr_lock_key.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the card supports CTAG acceleration we do not
account for the vlan header even if we are configuring an
8021AD vlan. This may not be best since we'll do software
tagging for 8021AD which will cause data copy on skb head expansion
Configure the length based on available hw offload capabilities and
vlan protocol.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan support 2 proto: 802.1q and 802.1ad, so make a new function
called vlan_dev_vlan_proto() which could return the vlan proto for
input dev.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With TX VLAN offload enabled the source MAC address for frames sent using the
VLAN interface is currently set to the address of the real interface. This is
wrong since the VLAN interface may be configured with a different address.
The bug was introduced in commit 2205369a31
("vlan: Fix header ops passthru when doing TX VLAN offload.").
This patch sets the source address before calling the create function of the
real interface.
Signed-off-by: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ether_addr_equal_64bits is more efficient than ether_addr_equal, and
can be used when each argument is an array within a structure that
contains at least two bytes of data beyond the array, so it is safe
to use it for vlan, and make sense for fast path.
Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According Joe's suggestion, maybe it'd be faster to add an unlikely to
the test for PCKET_OTHERHOST, so I add it and see whether the performance
could be better, although the differences is so small and negligible, but
it is hard to catch that any lower device would set the skb type to
PACKET_OTHERHOST, so most of time, I think it make sense to add unlikely
for the test.
Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace deprecated 'vconfig' tool with 'ip' from 'iproute2'. Add
some beautifications like replacing 'ethernet' with 'Ethernet' and
removing unneeded spaces.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
Provide a method for read-only access to the vlan device egress mapping.
Do this by refactoring vlan_dev_get_egress_qos_mask() such that now it
receives as an argument the skb priority instead of pointer to the skb.
Such an access is needed for the IBoE stack where the control plane
goes through the network stack. This is an add-on step on top of commit
d4a968658c "net/route: export symbol ip_tos2prio" which allowed the RDMA-CM
to use ip_tos2prio.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
