Only set the bits that are supported by the targeted devices.
This patch also removes duplicated set_bit calls.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.
Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"
Fixes: 6ecfe51b40 ("Input: refuse to register absolute devices without absinfo")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Tested-by: Juan Garrido <Juan.Garrido@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The `wacom_feature_mapping` function is careful to only set the the
touch_max value a single time, but this care does not extend to the
`wacom_wac_finger_event` function. In particular, if a device sends
multiple HID_DG_CONTACTMAX items in a single feature report, the
driver will end up retaining the value of last item.
The HID descriptor for the Cintiq Companion 2 does exactly this. It
incorrectly sets a "Report Count" of 2, which will cause the driver
to process two HID_DG_CONTACTCOUNT items. The first item has the actual
count, while the second item should have been declared as a constant
zero. The constant zero is the value the driver ends up using, however,
since it is the last HID_DG_CONTACTCOUNT in the report.
Report ID (16),
Usage (Contact Count Maximum), ; Contact count maximum (55h, static value)
Report Count (2),
Logical Maximum (10),
Feature (Variable),
To address this, we add a check that the touch_max is not already set
within the `wacom_wac_finger_event` function that processes the
HID_DG_TOUCHMAX item. We emit a warning if the value is set and ignore
the updated value.
This could potentially cause problems if there is a tablet which has
a similar issue but requires the last item to be used. This is unlikely,
however, since it would have to have a different non-zero value for
HID_DG_CONTACTMAX earlier in the same report, which makes no sense
except in the case of a firmware bug. Note that cases where the
HID_DG_CONTACTMAX items are in different reports is already handled
(and similarly ignored) by `wacom_feature_mapping` as mentioned above.
Link: https://github.com/linuxwacom/input-wacom/issues/223
Fixes: 184eccd403 ("HID: wacom: generic: read HID_DG_CONTACTMAX from any feature report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It has recently been reported that the "heartbeat" report from devices
like the 2nd-gen Intuos Pro (PTH-460, PTH-660, PTH-860) or the 2nd-gen
Bluetooth-enabled Intuos tablets (CTL-4100WL, CTL-6100WL) can cause the
driver to send a spurious BTN_TOUCH=0 once per second in the middle of
drawing. This can result in broken lines while drawing on Chrome OS.
The source of the issue has been traced back to a change which modified
the driver to only call `wacom_wac_pad_report()` once per report instead
of once per collection. As part of this change, pad-handling code was
removed from `wacom_wac_collection()` under the assumption that the
`WACOM_PEN_FIELD` and `WACOM_TOUCH_FIELD` checks would not be satisfied
when a pad or battery collection was being processed.
To be clear, the macros `WACOM_PAD_FIELD` and `WACOM_PEN_FIELD` do not
currently check exclusive conditions. In fact, most "pad" fields will
also appear to be "pen" fields simply due to their presence inside of
a Digitizer application collection. Because of this, the removal of
the check from `wacom_wac_collection()` just causes pad / battery
collections to instead trigger a call to `wacom_wac_pen_report()`
instead. The pen report function in turn resets the tip switch state
just prior to exiting, resulting in the observed BTN_TOUCH=0 symptom.
To correct this, we restore a version of the `WACOM_PAD_FIELD` check
in `wacom_wac_collection()` and return early. This effectively prevents
pad / battery collections from being reported until the very end of the
report as originally intended.
Fixes: d4b8efeb46 ("HID: wacom: generic: Correct pad syncing")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The state of the center button was not reported to userspace for the
2nd-gen Intuos Pro S when used over Bluetooth due to the pad handling
code not being updated to support its reduced number of buttons. This
patch uses the actual number of buttons present on the tablet to
assemble a button state bitmap.
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/112
Fixes: cd47de45b855 ("HID: wacom: Add 2nd gen Intuos Pro Small support")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 15893fa401.
The referenced commit broke pen and touch input for a variety of devices
such as the Cintiq Pro 32. Affected devices may appear to work normally
for a short amount of time, but eventually loose track of actual touch
state and can leave touch arbitration enabled which prevents the pen
from working. The commit is not itself required for any currently-available
Bluetooth device, and so we revert it to correct the behavior of broken
devices.
This breakage occurs due to a mismatch between the order of collections
and the order of usages on some devices. This commit tries to read the
contact count before processing events, but will fail if the contact
count does not occur prior to the first logical finger collection. This
is the case for devices like the Cintiq Pro 32 which place the contact
count at the very end of the report.
Without the contact count set, touches will only be partially processed.
The `wacom_wac_finger_slot` function will not open any slots since the
number of contacts seen is greater than the expectation of 0, but we will
still end up calling `input_mt_sync_frame` for each finger anyway. This
can cause problems for userspace separate from the issue currently taking
place in the kernel. Only once all of the individual finger collections
have been processed do we finally get to the enclosing collection which
contains the contact count. The value ends up being used for the *next*
report, however.
This delayed use of the contact count can cause the driver to loose track
of the actual touch state and believe that there are contacts down when
there aren't. This leaves touch arbitration enabled and prevents the pen
from working. It can also cause userspace to incorrectly treat single-
finger input as gestures.
Link: https://github.com/linuxwacom/input-wacom/issues/146
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Fixes: 15893fa401 ("HID: wacom: generic: read the number of expected touches on a per collection basis")
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A new PID is in use for repaired MobileStudio Pro devices. Add it to the
list of devices that need special-casing in wacom_wac_pad_event.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The HID descriptors for most Wacom devices oddly declare the serial
number and other related fields as signed integers. When these numbers
are ingested by the HID subsystem, they are automatically sign-extended
into 32-bit integers. We treat the fields as unsigned elsewhere in the
kernel and userspace, however, so this sign-extension causes problems.
In particular, the sign-extended tool ID sent to userspace as ABS_MISC
does not properly match unsigned IDs used by xf86-input-wacom and libwacom.
We introduce a function 'wacom_s32tou' that can undo the automatic sign
extension performed by 'hid_snto32'. We call this function when processing
the serial number and related fields to ensure that we are dealing with
and reporting the unsigned form. We opt to use this method rather than
adding a descriptor fixup in 'wacom_hid_usage_quirk' since it should be
more robust in the face of future devices.
Ref: https://github.com/linuxwacom/input-wacom/issues/134
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
CC: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_wac_pad_event is the only routine we need to update.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Wacom devices have keys with predefined meanings. However, when
support was originally added for these devices, the codes for these
keys were not available yet. These keys were thus reported with
the numbered KEY_PROG* range.
Some missing key codes were added with commit 4eb220cb35 ("HID:
wacom: generic: add 3 tablet touch keys") and we are now able to
report the proper key codes. We continue to report the original
KEY_PROG codes so as not to break any unknown applications that
may depend on them.
Also, to support the touch key, track its state in the pad report.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Link: https://gitlab.freedesktop.org/libinput/libinput/merge_requests/155
Link: https://github.com/linuxwacom/xf86-input-wacom/pull/46
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Addresses a few issues that were noticed when compiling with non-default
warnings enabled. The trimmed-down warnings in the order they are fixed
below are:
* declaration of 'size' shadows a parameter
* '%s' directive output may be truncated writing up to 5 bytes into a
region of size between 1 and 64
* pointer targets in initialization of 'char *' from 'unsigned char *'
differ in signedness
* left shift of negative value
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EKR ring claims a range of 0 to 71 but actually reports
values 1 to 72. The ring is used in relative mode so this
change should not affect users.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Fixes: 72b236d602 ("HID: wacom: Add support for Express Key Remote.")
Cc: <stable@vger.kernel.org> # v4.3+
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Distance values reported by 2nd-gen Intuos tablets are on an inverted
scale (0 == far, 63 == near). We need to change them over to a normal
scale before reporting to userspace or else userspace drivers and
applications can get confused.
Ref: https://github.com/linuxwacom/input-wacom/issues/98
Fixes: eda01dab53 ("HID: wacom: Add four new Intuos devices")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The bit indicating BTN_6 on this device is overshifted
by 2 bits, resulting in the incorrect button being
reported.
Also fix copy-paste mistake in comments.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/71
Fixes: c7f0522a1a ("HID: wacom: Slim down wacom_intuos_pad processing")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the product ID for the 2nd Generation Intuos Pro
Small to the touchring coordinate adjustment block.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Pull HID fixes from Jiri Kosina:
- regression fixes (reverts) for module loading changes that turned out
to be incompatible with some userspace, from Benjamin Tissoires
- regression fix for special Logitech unifiying receiver 0xc52f, from
Hans de Goede
- a few device ID additions to logitech driver, from Hans de Goede
- fix for Bluetooth support on 2nd-gen Wacom Intuos Pro, from Jason
Gerecke
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-dj: Fix 064d:c52f receiver support
Revert "HID: core: Call request_module before doing device_add"
Revert "HID: core: Do not call request_module() in async context"
Revert "HID: Increase maximum report size allowed by hid_field_extract()"
HID: a4tech: fix horizontal scrolling
HID: hyperv: Add a module description line
HID: logitech-hidpp: Add support for the S510 remote control
HID: multitouch: handle faulty Elo touch device
HID: wacom: Sync INTUOSP2_BT touch state after each frame if necessary
HID: wacom: Correct button numbering 2nd-gen Intuos Pro over Bluetooth
HID: wacom: Send BTN_TOUCH in response to INTUOSP2_BT eraser contact
HID: wacom: Don't report anything prior to the tool entering range
HID: wacom: Don't set tool type until we're in range
HID: rmi: Use SET_REPORT request on control endpoint for Acer Switch 3 and 5
HID: logitech-hidpp: add support for the MX5500 keyboard
HID: logitech-dj: add support for the Logitech MX5500's Bluetooth Mini-Receiver
HID: i2c-hid: add iBall Aer3 to descriptor override
Bluetooth connections may contain more than one set of touches,
or a partial set of touches, in one report.
Set the number of expected touches when reading a collection
instead of once per report (in the pre-report function).
Accordingly, reset the number of touches expected after each sync.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Finger data is separated into chunks in our Bluetooth report,
where each report contains the same number of chunks. Those chunks
are not aligned in any particular way to a set of finger touches.
That is, the first half of a group of simultaneous touches may
be in one chunk at the end of a report and the second half could
be at the beginning of the next report.
Also some chunks contain no data and potentially some chunks could
contain leftover (bad) data.
Introduce and process the WACOM_HID_WT_REPORT_VALID usage that the
device uses to let us know if we should process a chunk of data.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the generic code path, HID_DG_CONTACTMAX was previously
only read from the second byte of report 0x23.
Another report (0x82) has the HID_DG_CONTACTMAX in the
higher nibble of the third byte. We should support reading the
value of HID_DG_CONTACTMAX no matter what report we are reading
or which position that value is in.
To do this we submit the feature report as a event report
using hid_report_raw_event(). Our modified finger event path
records the value of HID_DG_CONTACTMAX when it sees that usage.
Fixes: 8ffffd5212 ("HID: wacom: fix timeout on probe for some wacoms")
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing INTUOSP2_BT device class supports LEDs and this device
does not. A new device class enum entry, "INTUOSP2S_BT", is created
to avoid the INTUOSP2_BT LED code.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Bluetooth interface of the 2nd-gen Intuos Pro batches together four
independent "frames" of finger data into a single report. Each frame
is essentially equivalent to a single USB report, with the up-to-10
fingers worth of information being spread across two frames. At the
moment the driver only calls `input_sync` after processing all four
frames have been processed, which can result in the driver sending
multiple updates for a single slot within the same SYN_REPORT. This
can confuse userspace, so modify the driver to sync more often if
necessary (i.e., after reporting the state of all fingers).
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The button numbering of the 2nd-gen Intuos Pro is not consistent between
the USB and Bluetooth interfaces. Over USB, the HID_GENERIC codepath
enumerates the eight ExpressKeys first (BTN_0 - BTN_7) followed by the
center modeswitch button (BTN_8). The Bluetooth codepath, however, has
the center modeswitch button as BTN_0 and the the eight ExpressKeys as
BTN_1 - BTN_8. To ensure userspace button mappings do not change
depending on how the tablet is connected, modify the Bluetooth codepath
to report buttons in the same order as USB.
To ensure the mode switch LED continues to toggle in response to the
mode switch button, the `wacom_is_led_toggled` function also requires
a small update.
Link: https://github.com/linuxwacom/input-wacom/pull/79
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The Bluetooth reports from the 2nd-gen Intuos Pro have separate bits for
indicating if the tip or eraser is in contact with the tablet. At the
moment, only the tip contact bit controls the state of the BTN_TOUCH
event. This prevents the eraser from working as expected. This commit
changes the driver to send BTN_TOUCH whenever either the tip or eraser
contact bit is set.
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
If the tool spends some time in prox before entering range, a series of
events (e.g. ABS_DISTANCE, MSC_SERIAL) can be sent before we or userspace
have any clue about the pen whose data is being reported. We need to hold
off on reporting anything until the pen has entered range. Since we still
want to report events that occur "in prox" after the pen has *left* range
we use 'wacom-tool[0]' as the indicator that the pen did at one point
enter range and provide us/userspace with tool type and serial number
information.
Fixes: a48324de6d ("HID: wacom: Bluetooth IRQ for Intuos Pro should handle prox/range")
Cc: <stable@vger.kernel.org> # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The serial number and tool type information that is reported by the tablet
while a pen is merely "in prox" instead of fully "in range" can be stale
and cause us to report incorrect tool information. Serial number, tool
type, and other information is only valid once the pen comes fully in range
so we should be careful to not use this information until that point.
In particular, this issue may cause the driver to incorectly report
BTN_TOOL_RUBBER after switching from the eraser tool back to the pen.
Fixes: a48324de6d ("HID: wacom: Bluetooth IRQ for Intuos Pro should handle prox/range")
Cc: <stable@vger.kernel.org> # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This affects the 2nd-gen Intuos Pro Medium and Large
when using their Bluetooth connection.
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only sync the pad once per report, not once per collection.
Also avoid syncing the pad on battery reports.
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, the driver will attempt to set the mode on all
devices with a center button, but some devices with a center
button lack LEDs, and attempting to set the LEDs on devices
without LEDs results in the kernel error message of the form:
"leds input8::wacom-0.1: Setting an LED's brightness failed (-32)"
This is because the generic codepath erroneously assumes that the
BUTTON_CENTER usage indicates that the device has LEDs, the
previously ignored TOUCH_RING_SETTING usage is a more accurate
indication of the existence of LEDs on the device.
Fixes: 10c55cacb8 ("HID: wacom: generic: support LEDs")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom has introduced a new pen compatible with its MobileStudio Pro and
other tablets. Although adding it to the tool ID tablet is not strictly
necessary unrecognized pens are reported as BTN_TOOL_PEN already, unless
the tablet sends the "eraser" bit, when BTN_TOOL_RUBBER is used instead),
we'll keep it updated anyway.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/hid/wacom_wac.c: In function ‘wacom_setup_pen_input_capabilities’:
drivers/hid/wacom_wac.c:3506:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
__clear_bit(ABS_MISC, input_dev->absbit);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/hid/wacom_wac.c:3508:2: note: here
case WACOM_MO:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'wacom_hid_usage_quirk' function is the intended home for fixing
up descriptors that are buggy or that don't quite fit the mold. Commit
578325120e was supposed to move all of these quirks but it missed the
code to handle fixup the serial number usages for AES pens. Lets move
this code out of 'wacom_wac_pen_usage_mapping' where it was previously
lurking and put it into the same place as the others.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The DTK-2451 and DTH-2452 have a buggy HID descriptor which incorrectly
contains a Cintiq-like report, complete with pen tilt, rotation, twist, serial
number, etc. The hardware doesn't actually support this data but our driver
duitifully sets up the device as though it does. To ensure userspace has a
correct view of devices without updated firmware, we clean up this incorrect
data in wacom_setup_device_quirks.
We're also careful to clear the WACOM_QUIRK_TOOLSERIAL flag since its presence
causes the driver to wait for serial number information (via
wacom_wac_pen_serial_enforce) that never comes, resulting in
the pen being non-responsive.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 8341720642 ("HID: wacom: Queue events with missing type/serial data for later processing")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touch sensors on the 2nd-gen Intuos tablets don't use a 4096x4096
sensor like other similar tablets (3rd-gen Bamboo, Intuos5, etc.).
The incorrect maximum XY values don't normally affect userspace since
touch input from these devices is typically relative rather than
absolute. It does, however, cause problems when absolute distances
need to be measured, e.g. for gesture recognition. Since the resolution
of the touch sensor on these devices is 10 units / mm (versus 100 for
the pen sensor), the proper maximum values can be calculated by simply
dividing by 10.
Fixes: b5fd2a3e92 ("Input: wacom - add support for three new Intuos devices")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Detecting the number of supported touches for a particular device used
to be tricky, both because early forms of the driver didn't have a very
good HID parser and because early hardware didn't always advertise the
actual number. At the time, we added a block of code which would ensure
that touch_max would always be equal to at least 1 on any touch device,
and relied on setting touch_max to e.g. 2 only for the multitouch-capable
exceptions.
The common case has since flipped, and the driver and descriptors can
reliably detect the number of touches supported by modern sensors.
Because of this, it makes sense to remove the fixup code and instead
place static declarations of "touch_max = 1" for these old devices. It
isn't entirely clear if all 2-finger devices actually report a maximum
number of touches so we leave these declarations still in place.
For the eagle-eyed, the "> BAMBOO_PT" condition was originally equivalent
to ">= TABLETPC", which is what the intent was. This commit doesn't have
to consider the types introduced in the interim since they shouldn't be
affected, hence why only the tablet PC definitions have been modified.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 1st-generation Intuos tablets (CTL-X80) include an "in range" flag
like some professional tablets. To ensure the pen remains usable at as
large as distance as possible (and to preemptively disable touch when
it is nearby) we need to ensure that we handle these "in range" events.
Handling of tool type identification has been moved to occur only when
the pen is fully in prox rather than any time the "stylus_in_proximity"
flag changes (which is controlled by the further-out "in range" flag).
Link: https://sourceforge.net/p/linuxwacom/bugs/358/
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/14
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/17
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code path for recent Bluetooth devices omits an exit report which
resets all the values of the device.
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Bluetooth reports contain multiple pen frames per report.
Each frame contains a flag indicating if the frame is valid.
Future Wacom devices with this type of report may contain HID
descriptors, add support for this usage to the generic codepath
of the Wacom driver.
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Wacom devices contain contain Pen and Pad usages in
the same report. Future devices of this type may utilize
HID Descriptors.
The generic code path of the Wacom driver previously
assumed pen, touch, and pad reports were delivered in
separate reports. This patch adds support for processing
each collection of a report separately, in order to support
reports with multiple tools.
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
