Configure the usb_ep using the SuperSpeedPlus descriptors if connected
in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable writing of SuperSpeedPlus descriptors for any SuperSpeedPlus
capable configuration when connected in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There are a couple places in the code that get the function descriptors
based on the speed. Move this lookup into a function call and add
support to handle the SuperSpeedPlus descriptors as well.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If enumerated in SuperSpeedPlus, count the configurations that support
it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When a function is added to a configuration with usb_add_function(), the
configuration speed flags are updated. These flags indicate for which
speeds the configuration is valid for.
This patch adds a flag in the configuration for SuperSpeedPlus and
also updates this based on the existence of ssp_descriptors.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a ssp_descriptors member to struct usb_function and handle the
initialization and cleanup of it. This holds the SuperSpeedPlus
descriptors for a function that supports SuperSpeedPlus. This is added
by usb_assign_descriptors().
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add the 'ssp_descriptors' parameter to the usb_assign_descriptors()
function. This allows a function driver to add descriptors for
SuperSpeedPlus speeds if it supports it.
Also update all uses of this function in the gadget subsystem so that
they pass NULL for the ssp_descriptors parameters.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a gadget supports SuperSpeedPlus or higher speeds, return a
SuperSpeedPlus USB Device Capability descriptor.
Currently this implementation returns a fixed descriptor with typical
values set.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB 3.1 specification replaces the USB 3.0 specification and all new
devices that are running at SuperSpeed or higher speeds must report a
bcdUSB of 0x0310.
Refer to USB 3.1 Specification, Revision 1.0, Section 9.6.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Avoid printing an error if adding the device failes with return
value EPROBE_DEFFER. This may happen e.g. due to missing GPIO for
the vbus-supply regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.
If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.
If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
retval is assigned to be -EOVERFLOW but is overwritten later before
it's used, remove this unused value assignment.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5QjC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some platforms don't have DMA, but we should still be able to build USB
drivers for these platforms. They could still be used through vhci_hcd,
usbip_host, or maybe something like USB passthrough in UML from a
capable host.
If NO_DMA=y:
ERROR: "dma_pool_destroy" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/core/usbcore.ko] undefined!
Add a few checks for CONFIG_HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The US_DEBUGPX macro uses printk without specifying a kernel log level, so
the default kernel log level is used, which may not match LOGLEVEL_DEBUG
used in usb_stor_dbg. Remove the macro and use usb_store_dbg instead.
Signed-off-by: Victor Dodon <printesoi@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device is disconnected poll waiters were not being woken.
Changes for v2:
- add commit summary
- add Fixes and Reported-by tags
Fixes: eb6b92ecc0 ("Add support for receiving USBTMC USB488 SRQ notifications via poll/select")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write value is 8bit, but currently writing a larger number (eg a doubled
digit) is not errored but instead gets cast and sets off an action probably
undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow for and clean handling of signals an URB is introduced.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shares the cleanup code between all probe failure paths, instead of
having per-failure cleanup at each point in the function.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4b61b4f205.
As reported by Oliver, this change was unnecessary.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d8f00cd685.
Tony writes:
This upstream commit is causing an oops:
d8f00cd685 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eFQw
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc5
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)
Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new interface for userspace to preallocate memory that can be
used with usbfs. This gives two primary benefits:
- Zerocopy; data no longer needs to be copied between the userspace
and the kernel, but can instead be read directly by the driver from
userspace's buffers. This works for all kinds of transfers (even if
nonsensical for control and interrupt transfers); isochronous also
no longer need to memset() the buffer to zero to avoid leaking kernel data.
- Once the buffers are allocated, USB transfers can no longer fail due to
memory fragmentation; previously, long-running programs could run into
problems finding a large enough contiguous memory chunk, especially on
embedded systems or at high rates.
Memory is allocated by using mmap() against the usbfs file descriptor,
and similarly deallocated by munmap(). Once memory has been allocated,
using it as pointers to a bulk or isochronous operation means you will
automatically get zerocopy behavior. Note that this also means you cannot
modify outgoing data until the transfer is complete. The same holds for
data on the same cache lines as incoming data; DMA modifying them at the
same time could lead to your changes being overwritten.
There's a new capability USBDEVFS_CAP_MMAP that userspace can query to see
if the running kernel supports this functionality, if just trying mmap() is
not acceptable.
Largely based on a patch by Markus Rechberger with some updates. The original
patch can be found at:
http://sundtek.de/support/devio_mmap_v0.4.diff
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
