We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values. For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided. It always contains the gpio
power setting (0 = off, 1 = on). To change the power setting, just write 0
or 1 to the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmwares require the dco itrim parameters to be set during
initialization. This patch implements the new ACX function and calls it.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init. We should use WL1271_DEFAULT_BASIC_RATE_SET instead. The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail. This patch adds the call and now PS seems to
work.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that. This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we're using a the idle information coming from mac80211 to decide when to
disconnect. If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command. So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we need to change the channel before association, we have to send a join
command with a valid BSSID. With this patch we use 0baddeadbeef as the
BSSID. There are ongoing discussions with TI to get this done in a cleaner
way.
When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were some changes in the values we have to use for these settings. This
patches updates them.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the general parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the radio parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.
Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The receive descriptor ops that are currently marked as being for
8687 only are actually used for all STA firmware images, whereas the
receive descriptor ops marked as 8366 are only used on 8366 when an
AP firmware image is in use.
Rename the receive descriptor ops to reflect this, use the STA ops
unconditionally if the firmware image loaded reported the STA ready
code, and rename the mwl8k_device_info::rxd_ops member to ap_rxd_ops
to indicate that it should only be used if we are running on AP
firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether the firmware we have loaded is AP or STA firmware decides
which receive descriptor format we have to use. Therefore, move
rx/tx ring initialisation to be after firmware loading.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sort firmware commands by command code, get rid of the 802_11 substring
in all command names, and make sure that the command functions match the
firmware command names.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous change added in:
commit 815833e7ec
ath9k: fix tx status reporting
was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.
This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.
Cc: stable@kernel.org
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rt2870 based device.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.
However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative. As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.
Move the initialization order around so the calibration interval
is set before interrupts are active. Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to signal a carrier off when doing a 802.11 scan.
Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the TX hang monitoring routine when doing a scan.
Monitoring for a hung situation is not really necessary during
a scan run.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cancel/restart the ANI timer directly.
With this patch, the ANI lock can be removed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k currently supports only RX interrupt
mitigation.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard-coding the SM PS mode per hardware,
this makes iwlwifi support the new mac80211 API for
controlling the SM PS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw always assumed that the storage device is at endpoint 1,
but there are devices (Spairon Homelink 1202) that are at endpoint 0.
Try both, starting with 1 to make sure to not break existing setups.
Signed-off-by: Stefan Seyfried <seife@sphairon.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since mac80211_hwsim supports multiple virtual interfaces, we need to
iterate through all active interfaces when figuring out whether there
is a match during TX Ack status checking. This fixes TX status
reporting for cases where secondary interfaces are used.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Determine the offset at compile time.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable was once set to WLAN_CAPABILITY_SHORT_PREAMBLE and
there's no code that could change the variable to something else.
Therefore it seems this is not necessary :-)
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly for the embedded people that know beforehand that they don't need
MESH at all and want to save some bytes, but also helpful for the upcoming
cfg80211 transition.
text data bss dec hex filename
114264 2308 140 116712 1c7e8 libertas.ko with mesh
105026 2000 140 107166 1a29e libertas.ko without mesh
--------------------------------------------------
-9238 -308 -9546
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While it's might be technically true that only MESH-enabled firmwares
are also RTAP-enabled, I like to have this decoupled.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_autostart_enabled was nowhere set. Rumor is that this is used in the
OLPC tree, but they never did submit their code upstream.
After removing this code, it turned out that the sync_channel stuff is now
also unused, so get rid of that as well.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both variables contained the same information (no mesh, old mesh, new mesh).
So we can get rid of one variable.
Also move the mesh-version test from cmd.c into mesh.c.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not that we actually ever aggregate anything, but
it could potentially be useful anyhow to simulate
aggregation sessions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the device receives an A-MSDU frame (indicated by flag
IWM_RX_TICKET_AMSDU_MSK), use ieee80211_amsdu_to_8023s to convert
it to a list of 802.3 frames and handled them to upper layer.
Cc: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that frames without payload are properly trimmed in
rt2x00queue_insert_l2pad.
This should fix the bug reported by Benoit Papillault in:
http://marc.info/?l=linux-wireless&m=125974773006734&w=2
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to Ralink source code, the RX frame format is RXINFO + RXWI +
802.11 frame + RXD, including various padding. Before this patch, we
were using RXD + RXWI + 802.11 frame, so RXD was not correct.
Doing this, we fix the L2PAD bit which is now correctly set on received
frames.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX aggregation is a way to receive multiple 802.11 frames in one RX buffer.
However, we don't know yet how to handle this case in rt2800usb_fill_rxdone
and this has probably no impact on RX performance as well, so we disable it
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
L2 padding will only be present when there is actual payload present.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the rt2x00queue_insert_l2pad function by handling the alignment
operations one by one. Do not special case special circumstances.
Basically first perform header alignment, and then perform payload alignment
(if any payload does exist). This results in a properly aligned skb.
The end result is better readable code, with better results, as now L2 padding
is inserted only when a payload is actually present in the frame.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the improved L2 padding code, this flag is no longer necessary, as the
rt2x00queue_remove_l2pad is capable of detecting by itself if L2 padding is
applied.
For received frames the RX descriptor flag is still being checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a couple of more bugs in the L2 padding code:
1. Compute the amount of L2 padding correctly (in 3 places).
2. Trim the skb correctly when the L2 padding has been applied.
Also introduce a central macro the compute the L2 padding size.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise we end up truncating the skb before removing the l2pad
thus we might have the truncated part become garbage while getting
it back in remove_l2pad.
For the same issue: remove the skb_trim from the rt2800 fill_rxdone
(it is done after l2pad removal in rt2x00lib_rxdone).
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not include timestamp for a frame that has been injected
through a monitor interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The padding is to be added between header and payload for the only header need
padding case.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
platform rfkill is async thus we may try to read while the device is
already off.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kenichi HORIO <moattailk1@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not need to log error when fail the sensitivity command, driver will send
sensitivity write command to uCode after each sensitivity calibration if
station is associated with AP. It is a normal case when user unload the module
or shutdown the system while still associated with the AP, since uCode already
on the way down, it will not reply the sensitivity write request; report
error in this case will give misleading information, remove the error checking
here to provide a clean shutdown if no other error detected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables the on-screen uCode event log dump. The original
method will append the event log to syslog; with this capability,
we also enable the user to write script to capture the
events which provide additional flexibility to help uCode debugging
Method
1) change to debugfs directory (sys/kernel/debug/phyX/iwlagn/data)
2) #cat log_event
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to help uCode debugging, adding the capability to provide
continuous uCode event logging function.
uCode events is located in round-robin event queue and filled by uCode,
by enable continuous event logging, driver check the write pointer
and log the newly added events in iwl_bg_ucode_trace() timer function.
There is still possibility of missing events if event queue being
wrapped before next event dump; but with this capability, we can have
much better understanding of the uCode behavior during runtime; it can
help to debug the uCode related issues.
Methods to enable/disable the continuous event log:
step 1: enable ucode trace timer
"echo 1 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
step 2: start ftrace
sudo ./trace-cmd record -e iwlwifi_ucode:* sleep 1d
step 3: stop ftrace
sudo ./trace-cmd report trace.dat
step 4: disable ucode trace timer
"echo 0 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
use "ucode_tracing" debugfs file to display number of event
queue wrapped when driver attempt the continuous event logging. If event
queue being wrapped more than once when driver has opportunity to log
the event; it indicated there are events missing in the event log trace.
This continuous event log function only available for 4965 and newer
NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode HW/SW error detected, dumping important CSR (Control and Status
Registers) values.
Also add "csr" debugfs file to dump the current values of CSR defined in
CSR table to syslog.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change name from RF_CARD_DISABLED to CT_CARD_DISABLED to match the
indication from uCode, also log the debug message when the condition
detected in iwl_rx_card_state_notif()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building rtl8180, the following warning occurs:
CC [M] drivers/net/wireless/rtl818x/rtl8180_dev.o
drivers/net/wireless/rtl818x/rtl8180_dev.c: In function ‘rtl8180_handle_rx’:
drivers/net/wireless/rtl818x/rtl8180_dev.c:135: warning: ‘qual’ is deprecated
(declared at include/net/mac80211.h:562)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan didn't copy module parameters for bcm4320a to private structure.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before transmission when aligning the buffer to 4-byte bounday, tx_hdr
needs to be updated. Otherwise debug logs print false data.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Based on a patch for wl1271 by Luis R. Rodriguez.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wakeup time calculation was too complicated, simplify it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original TI driver uses 100 ms timeout ELP wakeup timeout, better
to use the same. Otherwise problems with wakeup might get unnoticed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all return values were checked and one exit from function didn't put
firmware sleep after the error.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This debug message was missing and caused incomplete log messages.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes when debugging the state is good info.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a rather embarrassing typo.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch aggregates a bunch of small random changes
that won't fit really anywhere else properly.
1. move tid-locating macro into a separate function.
2. remove redundant NULL check.
3. add modulation mask definition
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flags in question were once useful for debugging.
Time has passed and now they do nothing more than
duplicating txinfo->flags.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9170 has the bad habit of choking when traffic builds up.
Tests have shown that this can partially be attributed to
a huge buildup of backlogged frames.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes dead infrastructure which was meant
for an out-of-tree rate control algorithm.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: https://bugs.launchpad.net/ubuntu/+bug/254837
Spurious shared interrupts or early probing interrupts can cause the
hostap interrupt handler to oops before the driver has fully configured
the IO base port addresses. In some cases the oops can be because
the hardware shares an interrupt line, on other cases it is due to a
race condition between probing for the hardware and configuring
the IO base port. The latter occurs because the probing is required to
determin the hardware port address which is only determined when the probe
can interrupt the hardware (catch 22).
This patch catches this pre-configured condition to avoid the oops.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed yesterday, because Jeff had noticed
a speed regression, cf. bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2138
that the SM PS settings for peers were wrong.
Instead of overwriting the SM PS settings with
the local bits, we need to keep the remote bits.
The bug was part of the original HT code from
over two years ago, but unfortunately nobody
noticed that it makes no sense -- we shouldn't
be overwriting the peer's setting with our own
but rather keep it intact when masking the peer
capabilities with our own.
While fixing that, I noticed that the masking of
capabilities is completely useless for most of
the bits, so also fix those other bits.
Finally, I also noticed that PSMP_SUPPORT no
longer exists in the final 802.11n version, so
also remove that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`queue' was unsigned so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver copies the SSID buffer back to the wireless core and
appends a trailing NULL character for termination. This is
a) unnecessary because the buffer is allocated with kzalloc and is hence
already NULLed when this function is called, and
b) for priv->curbssparams.ssid_len == 32, it writes back one byte too
much which causes memory corruptions.
Fix this by removing the extra write.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Maithili Hinge <maithili@marvell.com>
Cc: Kiran Divekar <dkiran@marvell.com>
Cc: Michael Hirsch <m.hirsch@raumfeld.com>
Cc: netdev@vger.kernel.org
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@lists.infradead.org
Cc: stable@kernel.org
Acked-by: Holger Schurig <holgerschurig@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX DMA termination has failed, the HW has to be reset
completely. Doing a fast channel change in this case is insufficient.
Also, change the debug level of a couple of messages to FATAL.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The internal, driver-specific maintenance of sequence
numbers is applicable only for HT frames.
Also, remove comments that are not relevant anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix typo. The index should be multiplied by the entry size, not 'and'-ed.
Found via code-inspection.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have 40MHz operation disabled entirely. Ensure that driver do
not enable 40MHz operation if a channel does not allow this.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2135
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
- next_link_addr = link_value * sizeof(u16);
+ next_link_addr = le16_to_cpu(link_value) * sizeof(u16);
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sizeof(iv16) and sizeof(iv32) are the sizes of pointers. Change them to
the size of the copied data.
Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function. Thus, there would
seem to be no point to copy data into it. The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.
A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib incorrectly detected whether RT2800USB was enabled because
it didn't account for a modularized RT2800USB driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As shown in Kernel Bugzilla #14761, doing a controller restart after a
fatal DMA error does not accomplish anything other than consume the CPU
on an affected system. Accordingly, substitute a meaningful message for
the restart.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch reports that his rtl8187 gives warnings on suspend
("queueing ieee80211 work while going to suspend" warnings), as rtl8187
can call ieee80211_queue_delayed_work after mac80211 is suspended.
This change enhances rtl8187 led code so we can avoid queuing work after
mac80211 is suspended: now we register a radio led and make additional
checks to ensure led is off/on properly as mac80211 wants.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this we have no gaurantee of the integrity of the
EEPROM and are likely to encounter a lot of bogus bug reports
due to actual issues on the EEPROM. With the EEPROM checksum
check in place we can easily rule those issues out.
If you run patch during a revert *you* have a card with a busted
EEPROM and only older kernel will support that concoction. This
patch is a trade off between not accepitng bogus EEPROMs and
avoiding bogus bug reports allowing developers to focus instead
on real concrete issues.
If stable keeps bogus bug reports because of a possibly busted EEPROM
feel free to apply this there too.
Tested on an AR5414
Cc: stable@kernel.org
Cc: jirislaby@gmail.com
Cc: akpm@linux-foundation.org
Cc: rjw@sisk.pl
Cc: me@bobcopeland.com
Cc: david.quan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds support for the WiFi activity LED on the Dell Vostro A860 laptop.
Signed-off-by: Shahar Or <shahar@shahar-or.co.il>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A KERN_DEBUG didn't get removed when transitioning from printk to
pr_debug
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.
This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k's tx status check, which
caused mac80211 to consider regularly transmitted unicast frames
as un-acked.
When checking the ts_status field for errors, it needs to be masked
with ATH9K_TXERR_FILT, because this field also contains other fields
like ATH9K_TX_ACKED.
Without this patch, AP mode is pretty much unusable, as hostapd
checks the ACK status for the frames that it injects.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FINALIZE_JOIN firmware command only looks at the first couple of
fields in the beacon, and therefore it's not necessary to complain if
the beacon is longer than 128 bytes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disassociating, mac80211 zeroes vif->bss_info.bssid before
calling our ->bss_info_changed(), but we need the BSSID to remove the
hardware station database entry for our AP, so we can't clear our
local copy of the BSSID until after we've done that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to call pci_disable_device() if pci_request_regions()
fails during probe.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index. Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.
Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.
This fixes both of these issues.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field. For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.
We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).
Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.
This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet. It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.
Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.
To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.
In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length. Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise
templates will have incorrect bssid and power save will not work
correctly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a warning from wl1251_op_bss_info_changed():
wl1251: WARNING Set ctsprotect failed 0
It was printed always, it's completely false and can be removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging the wifi firmware, we need to disable the wimax core to gain
some memory space. The default value will keep the wimax core enabled.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wifi and wimax coexistence mode is set by wifi at boot time. There can be
several modes, defined by priority tables. User space components can decide
which one to select by writing to /sys/module/iwmc3200wifi/parameters/wiwi
with this patch, before bringing the interface up.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
