The reason of including <linux/bitops.h> here is just for BIT() macro.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin 327 was supposed to be used as a voltage control line for the
SD card regulator, but the SD card port1 does not support UHS-I. It
only supports 3.3V signaling, hence this pin is pointless.
Just a note about the background. At first, hardware engineers tried
to implement the UHS for this port. Then, they needed to shrink the
silicon die size, and gave up the UHS, but forgot to remove the pin
assignment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No core changes this time! Just a calm all-over-the-place
drivers, updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions
variants for S700, S500 in the pipe. Also generic GPIO
support on top of the same driver and IRQ support is in
the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview.
-----BEGIN PGP SIGNATURE-----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=6On2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v4.18.
No core changes this time! Just a calm all-over-the-place drivers,
updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions variants for
S700, S500 in the pipe. Also generic GPIO support on top of the
same driver and IRQ support is in the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview"
* tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
pinctrl: at91-pio4: add missing of_node_put
pinctrl: armada-37xx: Fix spurious irq management
gpiolib: discourage gpiochip_add_pin[group]_range for DT pinctrls
pinctrl: msm: fix gpio-hog related boot issues
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: mediatek: remove unused fields in struct mtk_eint_hw
pinctrl: mediatek: use generic EINT register maps for each SoC
pinctrl: mediatek: add EINT support to MT7622 SoC
pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit
dt-bindings: pinctrl: add external interrupt support to MT7622 pinctrl
pinctrl: freescale: Switch to SPDX identifier
pinctrl: samsung: Fix suspend/resume for Exynos5433 GPF1..5 banks
pinctrl: sh-pfc: rcar-gen3: Fix grammar in static pin comments
pinctrl: sh-pfc: r8a77965: Add I2C pin support
pinctrl: sh-pfc: r8a77990: Add EthernetAVB pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add I2C{1,2,4,5,6,7} pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add SCIF pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add bias pinconf support
pinctrl: sh-pfc: Initial R8A77990 PFC support
...
UniPhier SoCs have the following pins for hardware flow control of UART:
XRTS, XCTS
and for modem control of UART:
XDTR, XDSR, XDCD, XRI
The port number with the flow control is SoC-dependent.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is code duplication between uniphier_conf_pin_drive_get() and
uniphier_conf_pin_drive_set(). Factor out the common code into
uniphier_conf_get_drvctrl_data().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is handled by the mmc-pwrseq-emmc driver, which controls
an eMMC hardware reset via a GPIO line.
Remove it from the function pin-mux settings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Don't populate const arrays on the stack, instead make them
static. Makes the object code smaller nearly 1000 bytes. Also
line break wide lines to avoid checkpatch warnings.
Before:
text data bss dec hex filename
13112 1996 0 15108 3b04 pinctrl-uniphier-core.o
After:
text data bss dec hex filename
11642 2476 0 14118 3726 pinctrl-uniphier-core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The #includes <linux/bug.h> is here to use BUILD_BUG_ON_ZERO().
Thanks to commit bc6245e5ef ("bug: split BUILD_BUG stuff out into
<linux/build_bug.h>"), it is now possible to reduce the number of
headers pulled in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ether_rmii_groups should have "ether_rmii" and "ether_rmiib" as
members. This patch replaces to them.
Fixes: 1e359ab128 ("pinctrl: uniphier: add Ethernet pin-mux settings")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 58957d2edf ("pinctrl: Widen the generic pinconf argument
from 16 to 24 bits"), the generic pinconf arguments are handled by u32.
UniPhier pinctrl drivers do not support debouncing, so u16 is working,
but align the argument type to u32 for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Save registers lost in the sleep when suspending, and restore them
when resuming.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/20 SoCs (capable of per-pin input enable), the iectrl bit
number matches its pin number. So, this is redundant information.
Instead, we just need a flag to know if the iectrl gating exists or not.
With this refactoring, 5 bits in pin data will be saved.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a bunch of GPIO muxing data, but most of them are actually
unneeded because GPIO-to-pin mapping can be specified by "gpio-ranges"
DT properties.
Tables that contain a set of GPIO pins are still needed for the named
mapping by "gpio-ranges-group-names". This is a much cleaner way for
UniPhier SoC family where GPIO numbers are not straight mapped to pin
numbers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/LD20 SoCs (capable of per-pin input enable), iectrl bits are
located across multiple registers. So, the register offset must be
taken into account. Otherwise, wrong input-enable status is displayed.
While we here, rename the macro because it is a base address.
Fixes: aa543888ca ("pinctrl: uniphier: support per-pin input enable for new SoCs")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All UniPhier pinctrl drivers are built-in. Exporting the symbol
is meaningless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinctrl assignment for Pro4, each definition of USB#2 and
USB#3 are as follows.
184: USB2VBUS
185: USB2OD
186: USB2ID
187: USB3VBUS
188: USB3OD
USB#2 has an additional pin "USB2ID", but the chip doesn't use this pin
while in host-mode. Considering this pin, the pin definitions for USB#3
should be {187, 188}.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZCG0aAAoJEEEQszewGV1zBpcP/37y0m2ZFIqVJrqlPKVeZbRa
aYwsbY3l9OGeocLXSRWaqLJkwJ+WaG8ascoXHLMgk4jFC2CutwUea0fzhy9Li2VO
Sqd/BN9iNd/g2lTf8o37NM5qYF5IvStZu12DzFPRFpec6pEiYOHVmRiSlIK5lREG
v/NGNAIzLPH59jRHA17sLT1lkHmiT43S4Gm38nvpar8vfO+2UkAwGVPQPC8dGuL9
gydMLLtx3d1SzWqicbMSICa/F7kjWz5I4jL6KM7ohVGXgDn8tdZk+7rERfBD9qoR
eDNPZvXajaC6y3S3h6Ynv094X30w3VA0xtj9kPVhJsS1yUlVli5GlC3WHPArwrRQ
sXx29UsdTmAjzHHns4OZfxKnEVvHbXtW1XmX+ks248f/k8hCVWpQA9ZENvVHjLvu
NkDwXOmTWOxjutDveZqm7RM6z+99+lRgzLgwB3GMENIUC8ohH79W/R9GYHvrqOZI
hWX+G/q3nnnW3cIPc15rN2MC3fkjE2mdFC0N+/kDlKtzPabCS8U6JZsfQDulX5m1
I2xF2DY+1WWCy1mMDpyTdYNDlkOGU8j/N5MXx9z1629m+vjg0KZo35+mGwJh5mA1
gQ6rI3DdhS5qVK2Gj/joYkwQ1cKpdEtljlpI9A+WdXx1eO7RKVK1m1fxbd8c47L/
I0qdXsL66ZtiKDOIDPau
=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
At first these drivers were written as tristate, but the module
usecases are actually not tested. Make all of them boolean.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 3e030b0b4e ("pinctrl: uniphier: allow to have pinctrl
node under syscon node"), this driver has kept compatibility for the
old DT files. Several releases have passed since then, so remove
the obsoleted compatibles and clean up the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch changes pin names of AIO and XIRQ according to updated
specification.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This SoC has no SD card controller. Nor does it have USB port3.
These pin-mux settings have no point.
Fixes: 70f2f9c4cf ("pinctrl: uniphier: add UniPhier PH1-LD11 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are input-only pins. They do not support drive controlling
in the first place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the hardware document, setting the drive control is
prohibited for these pins (N-channel Open Drain pins). Set their
drive control attribute to "fixed".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My mistake in the initial support patches.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node.
To allow to migrate to the new DT structure, this commit adds new
compatible strings to not disturb the existing DT. After a while,
the old binding will be removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is needed to get access to UniPhier System Bus (external bus).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These pins do not support pin-muxing, but it is useful to support
pin configuration for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit updates the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding the new one. Having just one flag would be
better than adding a new struct member every time a new SoC-specific
capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from a customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
