This makes the macros a little bit safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pll_flags quirk just returned the extra PLL flags the sensor required,
but the init quirk is far more versatile. It can be used to perform any
extra initialisation needed by the sensor, including allocating memory for
sensor specific struct and creating sensor specific new controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As the controls creation is separated in two sections, the available media
bus codes and link frequencies can be enumerated later on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The default values and limits for certain controls need the knowledge of
available media bus codes or link frequencies. Create such controls later
on, so that most of the initialisation of the sensor has already been done
when the init quirk is called.
[mchehab@osg.samsung.com: make checkpatch.pl happier]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clean up smiapp_init_controls() by adding newlines to appropriate places and
by removing superfluous error handling. The caller will clean up control
handlers in any case if the function fails.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Also call smiapp_cleanup() in smiapp_remove(), replacing code that did the
same than the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The flash capability register is already read as part of the limit
registers. Do no access it separately; instead use the value from the
limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.
This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform data support is retained.
of_property_read_u64_array() isn't used yet as it's not in yet.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SMIA compatible sensors only need a single clock.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The source sub-device's name will be overwritten shortly. Don't give it a
name in the meantime.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct device has a forward declaration in the header already. The header is
only needed in the .c file.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Timo Ahonen <timo.ahonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:344:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:354:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:364:24: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:366:23: warning: cast to restricted __le16
The get_unaligned_le*() functions return the value using cpu endianness,
so calling le*_to_cpu is wrong.
It hasn't been not noticed because this code has only been run on little
endian systems, so le*_to_cpu doesn't do anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers depend on VIDEO_V4L2_SUBDEV_API, which in turn
depends on MEDIA_CONTROLLER. So it is sufficient to just depend
on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1rPM
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second set of media updates from Mauro Carvalho Chehab:
- Move drivers for really old legacy hardware to staging. Those are
using obsolete media kAPIs and are for hardware that nobody uses for
years. Simply not worth porting them to the new kAPIs. Of course,
if anyone pops up to fix, we can move them back from there
- While not too late, do some API fixups at the new colorspace API,
added for v3.19
- Some improvements for rcar_vin driver
- Some fixups at cx88 and vivid drivers
- Some Documentation fixups
* tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] bq/c-qcam, w9966, pms: move to staging in preparation for removal
[media] tlg2300: move to staging in preparation for removal
[media] vino/saa7191: move to staging in preparation for removal
[media] MAINTAINERS: vivi -> vivid
[media] cx88: remove leftover start_video_dma() call
[media] cx88: add missing alloc_ctx support
[media] v4l2-ioctl: WARN_ON if querycap didn't fill device_caps
[media] vivid: fix CROP_BOUNDS typo for video output
[media] DocBook media: update version number and document changes
[media] vivid.txt: document new controls
[media] DocBook media: add missing ycbcr_enc and quantization fields
[media] v4l2-mediabus.h: use two __u16 instead of two __u32
[media] rcar_vin: Fix interrupt enable in progressive
[media] rcar_vin: Enable VSYNC field toggle mode
[media] rcar_vin: Add scaling support
[media] rcar_vin: Add DT support for r8a7793 and r8a7794 SoCs
[media] rcar_vin: Add YUYV capture format support
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
Add support for selection target V4L2_SEL_TGT_NATIVE_SIZE. It is equivalent
of what V4L2_SEL_TGT_CROP_BOUNDS used to be. Support for
V4L2_SEL_TGT_CROP_BOUNDS is still supported by the driver as a compatibility
interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The fields were previously uninitialised, leaving the returned values to
where the user had set them. This was never the intention.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for YCbCr output and support setting colorspace,
YCbCr encoding and quantization for the AVI InfoFrame.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rc_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Replace all references to the old definitions in i2c drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have v4l2-compliance tool pass the G/S_EDID some modifications
where needed in the driver.
In particular, the edid.reserved zone must be blanked.
Based on a patch from Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>,
but reworked it a bit. It should use 'data' (which depends on edid.present)
instead of edid.blocks as the check whether edid data is present.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the v4l2-compliance failures.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this pass the v4l2-compliance test.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
This use has a mask then shift which is not the normal style.
Move the shift before the mask to match nearly all the other
uses in kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to report:
cx25840 7-0044: Firmware download size changed to 16 bytes max length
If the driver needs to adjust the buffer's maximum size.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media bus format BPP does affect PLL. Recalculate PLL if the format
changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set supported link frequencies in the menu in control initialisation and
when the bpp changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
smiapp_set_format() has accumulated a fair amount of changes without a
needed refactoring, do the cleanup now. There's also an unlocked version of
v4l2_ctrl_range_changed(), using that fixes a small serialisation issue with
the user space interface.
__v4l2_ctrl_modify_range() is used instead of v4l2_ctrl_modify_range() in
smiapp_set_format_source() since the mutex is now held during the function
call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some media bus codes may be unavailable depending on the available media bus
codes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all link rates are possible with all BPP values.
Also rearrange other initialisation a little. Obtaining possible PLL
configurations earlier requires that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The first one is handy for just trying out a PLL configuration without a
need to apply it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The actual pixel array pixel rate may be something else than vt_pix_clk_freq
on some implementations. Add a new field which contains the corrected value.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
op_pix_clk_div is directly assigned and not calculated. There's no need to
verify it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need to pretend the OP limits are there anymore.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For profile 0 sensors (which have no OP clocks), the OP limits are in fact
VT limits. Do not verify them again.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Profile 0 sensors have no OP clock branck in the clock tree. The PLL
calculator still calculated them, they just weren't used for anything.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Uniform representation for VT and OP clocks. This is preparation for
calculating the VT clocks using the OP clock code.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
