ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
tick_broadcast_oneshot_control got moved from tick-broadcast to
tick-common, but the export stayed in the old place. Fix it up.
Fixes: f32dd11705 'tick/broadcast: Make idle check independent from mode and config'
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently the broadcast busy check, which prevents the idle code from
going into deep idle, works only in one shot mode.
If NOHZ and HIGHRES are off (config or command line) there is no
sanity check at all, so under certain conditions cpus are allowed to
go into deep idle, where the local timer stops, and are not woken up
again because there is no broadcast timer installed or a hrtimer based
broadcast device is not evaluated.
Move tick_broadcast_oneshot_control() into the common code and provide
proper subfunctions for the various config combinations.
The common check in tick_broadcast_oneshot_control() is for the C3STOP
misfeature flag of the local clock event device. If its not set, idle
can proceed. If set, further checks are necessary.
Provide checks for the trivial cases:
- If broadcast is disabled in the config, then return busy
- If oneshot mode (NOHZ/HIGHES) is disabled in the config, return
busy if the broadcast device is hrtimer based.
- If oneshot mode is enabled in the config call the original
tick_broadcast_oneshot_control() function. That function needs
extra checks which will be implemented in seperate patches.
[ Split out from a larger combo patch ]
Reported-and-tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Suzuki Poulose <Suzuki.Poulose@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Catalin Marinas <Catalin.Marinas@arm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1507070929360.3916@nanos
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
We want to rename dev->state, so provide proper get and set
functions. Rename clockevents_set_state() to
clockevents_switch_state() to avoid confusion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Since idle_should_freeze() is defined to always return 'false'
for CONFIG_SUSPEND unset, all of the code depending on it in
cpuidle_idle_call() is not necessary in that case.
Make that code depend on CONFIG_SUSPEND too to avoid building it
when it is not going to be used.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add suspend/resume tracepoints to tick_freeze() and tick_unfreeze()
to catch when timekeeping is suspended and resumed during suspend-to-idle
so as to be able to check whether or not we enter the "frozen" state
and to measure the time spent in it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
hrtimer softirq is a leftover from the initial implementation and
serves only the purpose to handle the enqueueing of already expired
timers in the high resolution timer mode. We discussed whether we
change the return value and force all start sites to handle that the
timer is already expired, but that would be a Herculean task and I'm
not sure whether its a good idea to enforce that handling on
everyone.
A simpler solution is to enforce a timer interrupt instead of raising
and scheduling a softirq. Just use the existing infrastructure to do
so and remove all the softirq leftovers.
The HRTIMER softirq enum is now unused, but kept around because trace
parsers rely on the existing numbering.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20150414203501.840834708@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
clockevents_notify() is a leftover from the early design of the
clockevents facility. It's really not a notification mechanism,
it's a multiplex call. We are way better off to have explicit
calls instead of this monstrosity.
Split out the cleanup function for a dead cpu and invoke it
directly from the cpu down code. Make it conditional on
CPU_HOTPLUG as well.
Temporary change, will be refined in the future.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Rebased, added clockevents_notify() removal ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1735025.raBZdQHM3m@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
clockevents_notify() is a leftover from the early design of the
clockevents facility. It's really not a notification mechanism,
it's a multiplex call. We are way better off to have explicit
calls instead of this monstrosity.
Split out the tick_handover call and invoke it explicitely from
the hotplug code. Temporary solution will be cleaned up in later
patches.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Rebase ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1658173.RkEEILFiQZ@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the new tick_suspend/resume_local() and get rid of the
homebrewn implementation of these in the ARM bL switcher. The
check for the cpumask is completely pointless. There is no harm
to suspend a per cpu tick device unconditionally. If that's a
real issue then we fix it proper at the core level and not with
some completely undocumented hacks in some random core code.
Move the tick internals to the core code, now that this nuisance
is gone.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ rjw: Rebase, changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1655112.Ws17YsMfN7@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xen calls on every cpu into tick_resume() which is just wrong.
tick_resume() is for the syscore global suspend/resume
invocation. What XEN really wants is a per cpu local resume
function.
Provide a tick_resume_local() function and use it in XEN.
Also provide a complementary tick_suspend_local() and modify
tick_unfreeze() and tick_freeze(), respectively, to use the
new local tick resume/suspend functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Combined two patches, rebased, modified subject/changelog. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1698741.eezk9tnXtG@vostro.rjw.lan
[ Merged to latest timers/core. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
clockevents_notify() is a leftover from the early design of the
clockevents facility. It's really not a notification mechanism,
it's a multiplex call.
We are way better off to have explicit calls instead of this
monstrosity. Split out the suspend/resume() calls and invoke
them directly from the call sites.
No locking required at this point because these calls happen
with interrupts disabled and a single cpu online.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ Rebased on top of 4.0-rc5. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/713674030.jVm1qaHuPf@vostro.rjw.lan
[ Rebased on top of latest timers/core. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
'enum clock_event_mode' is used for two purposes today:
- to pass mode to the driver of clockevent device::set_mode().
- for managing state of the device for clockevents core.
For supporting new modes/states we have moved away from the
legacy set_mode() callback to new per-mode/state callbacks. New
modes/states shouldn't be exposed to the legacy (now OBSOLOTE)
callbacks and so we shouldn't add new states to 'enum
clock_event_mode'.
Lets have separate enums for the two use cases mentioned above.
Keep using the earlier enum for legacy set_mode() callback and
mark it OBSOLETE. And add another enum to clearly specify the
possible states of a clockevent device.
This also renames the newly added per-mode callbacks to reflect
state changes.
We haven't got rid of 'mode' member of 'struct
clock_event_device' as it is used by some of the clockevent
drivers and it would automatically die down once we migrate
those drivers to the new interface. It ('mode') is only updated
now for the drivers using the legacy interface.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: linaro-kernel@lists.linaro.org
Cc: linaro-networking@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/b6b0143a8a57bd58352ad35e08c25424c879c0cb.1425037853.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Upcoming patch will redefine possible states of a clockevent
device. The RESUME mode is a special case only for tick's
clockevent devices. In future it can be replaced by ->resume()
callback already available for clockevent devices.
Lets handle it separately so that clockevents_set_mode() only
handles states valid across all devices. This also renames
set_mode_resume() to tick_resume() to make it more explicit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: linaro-kernel@lists.linaro.org
Cc: linaro-networking@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/c1b0112410870f49e7bf06958e1483eac6c15e20.1425037853.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The efficiency of suspend-to-idle depends on being able to keep CPUs
in the deepest available idle states for as much time as possible.
Ideally, they should only be brought out of idle by system wakeup
interrupts.
However, timer interrupts occurring periodically prevent that from
happening and it is not practical to chase all of the "misbehaving"
timers in a whack-a-mole fashion. A much more effective approach is
to suspend the local ticks for all CPUs and the entire timekeeping
along the lines of what is done during full suspend, which also
helps to keep suspend-to-idle and full suspend reasonably similar.
The idea is to suspend the local tick on each CPU executing
cpuidle_enter_freeze() and to make the last of them suspend the
entire timekeeping. That should prevent timer interrupts from
triggering until an IO interrupt wakes up one of the CPUs. It
needs to be done with interrupts disabled on all of the CPUs,
though, because otherwise the suspended clocksource might be
accessed by an interrupt handler which might lead to fatal
consequences.
Unfortunately, the existing ->enter callbacks provided by cpuidle
drivers generally cannot be used for implementing that, because some
of them re-enable interrupts temporarily and some idle entry methods
cause interrupts to be re-enabled automatically on exit. Also some
of these callbacks manipulate local clock event devices of the CPUs
which really shouldn't be done after suspending their ticks.
To overcome that difficulty, introduce a new cpuidle state callback,
->enter_freeze, that will be guaranteed (1) to keep interrupts
disabled all the time (and return with interrupts disabled) and (2)
not to touch the CPU timer devices. Modify cpuidle_enter_freeze() to
look for the deepest available idle state with ->enter_freeze present
and to make the CPU execute that callback with suspended tick (and the
last of the online CPUs to execute it with suspended timekeeping).
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
This way we unbloat a bit main.c and more importantly we initialize
nohz full after init_IRQ(). This dependency will be needed in further
patches because nohz full needs irq work to raise its own IRQ.
Information about the support for this ability on ARM64 is obtained on
init_IRQ() which initialize the pointer to __smp_call_function.
Since tick_init() is called right after init_IRQ(), this is a good place
to call tick_nohz_init() and prepare for that dependency.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Convert uses of __get_cpu_var for creating a address from a percpu
offset to this_cpu_ptr.
The two cases where get_cpu_var is used to actually access a percpu
variable are changed to use this_cpu_read/raw_cpu_read.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since the xtime lock was split into the timekeeping lock and
the jiffies lock, we no longer need to call update_wall_time()
while holding the jiffies lock.
Thus, this patch splits update_wall_time() out from do_timer().
This allows us to get away from calling clock_was_set_delayed()
in update_wall_time() and instead use the standard clock_was_set()
call that previously would deadlock, as it causes the jiffies lock
to be acquired.
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The recent implementation of a generic dummy timer resulted in a
different registration order of per cpu local timers which made the
broadcast control logic go belly up.
If the dummy timer is the first clock event device which is registered
for a CPU, then it is installed, the broadcast timer is initialized
and the CPU is marked as broadcast target.
If a real clock event device is installed after that, we can fail to
take the CPU out of the broadcast mask. In the worst case we end up
with two periodic timer events firing for the same CPU. One from the
per cpu hardware device and one from the broadcast.
Now the problem is that we have no way to distinguish whether the
system is in a state which makes broadcasting necessary or the
broadcast bit was set due to the nonfunctional dummy timer
installment.
To solve this we need to keep track of the system state seperately and
provide a more detailed decision logic whether we keep the CPU in
broadcast mode or not.
The old decision logic only clears the broadcast mode, if the newly
installed clock event device is not affected by power states.
The new logic clears the broadcast mode if one of the following is
true:
- The new device is not affected by power states.
- The system is not in a power state affected mode
- The system has switched to oneshot mode. The oneshot broadcast is
controlled from the deep idle state. The CPU is not in idle at
this point, so it's safe to remove it from the mask.
If we clear the broadcast bit for the CPU when a new device is
installed, we also shutdown the broadcast device when this was the
last CPU in the broadcast mask.
If the broadcast bit is kept, then we leave the new device in shutdown
state and rely on the broadcast to deliver the timer interrupts via
the broadcast ipis.
Reported-and-tested-by: Stehle Vincent-B46079 <B46079@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Mark Rutland <mark.rutland@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1307012153060.4013@ionos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On an SMP system with only one global clockevent and a dummy
clockevent per CPU we run into problems. We want the dummy
clockevents to be registered as the per CPU tick devices, but
we can only achieve that if we register the dummy clockevents
before the global clockevent or if we artificially inflate the
rating of the dummy clockevents to be higher than the rating
of the global clockevent. Failure to do so leads to boot
hangs when the dummy timers are registered on all other CPUs
besides the CPU that accepted the global clockevent as its tick
device and there is no broadcast timer to poke the dummy
devices.
If we're registering multiple clockevents and one clockevent is
global and the other is local to a particular CPU we should
choose to use the local clockevent regardless of the rating of
the device. This way, if the clockevent is a dummy it will take
the tick device duty as long as there isn't a higher rated tick
device and any global clockevent will be bumped out into
broadcast mode, fixing the problem described above.
Reported-and-tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: soren.brinkmann@xilinx.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20130613183950.GA32061@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide a sysfs interface to allow unbinding of clockevent
devices. The device is unbound if it is unused or if there is a
replacement device available. Unbinding of broadcast devices is not
supported as we don't want to foster that nonsense. If no replacement
device is available the unbind returns -EBUSY. Unbind is available
from the kernel and through sysfs, which is necessary to drop the
module refcount.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.499216659@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split out the clockevent device selection logic. Preparatory patch to
allow unbinding active clockevent devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.431796247@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We want to be able to remove clockevent modules as well. Add a
refcount so we don't remove a module with an active clock event
device.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.307435149@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No need to call another function and have duplicated cases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.235746557@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that the notifier chain is gone there are no other users and it's
pointless to nest tick_device_lock inside of clockevents_lock because
there is no other use case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.162888472@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
7+ years and still a single user. Kill it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.098520211@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull 'full dynticks' support from Ingo Molnar:
"This tree from Frederic Weisbecker adds a new, (exciting! :-) core
kernel feature to the timer and scheduler subsystems: 'full dynticks',
or CONFIG_NO_HZ_FULL=y.
This feature extends the nohz variable-size timer tick feature from
idle to busy CPUs (running at most one task) as well, potentially
reducing the number of timer interrupts significantly.
This feature got motivated by real-time folks and the -rt tree, but
the general utility and motivation of full-dynticks runs wider than
that:
- HPC workloads get faster: CPUs running a single task should be able
to utilize a maximum amount of CPU power. A periodic timer tick at
HZ=1000 can cause a constant overhead of up to 1.0%. This feature
removes that overhead - and speeds up the system by 0.5%-1.0% on
typical distro configs even on modern systems.
- Real-time workload latency reduction: CPUs running critical tasks
should experience as little jitter as possible. The last remaining
source of kernel-related jitter was the periodic timer tick.
- A single task executing on a CPU is a pretty common situation,
especially with an increasing number of cores/CPUs, so this feature
helps desktop and mobile workloads as well.
The cost of the feature is mainly related to increased timer
reprogramming overhead when a CPU switches its tick period, and thus
slightly longer to-idle and from-idle latency.
Configuration-wise a third mode of operation is added to the existing
two NOHZ kconfig modes:
- CONFIG_HZ_PERIODIC: [formerly !CONFIG_NO_HZ], now explicitly named
as a config option. This is the traditional Linux periodic tick
design: there's a HZ tick going on all the time, regardless of
whether a CPU is idle or not.
- CONFIG_NO_HZ_IDLE: [formerly CONFIG_NO_HZ=y], this turns off the
periodic tick when a CPU enters idle mode.
- CONFIG_NO_HZ_FULL: this new mode, in addition to turning off the
tick when a CPU is idle, also slows the tick down to 1 Hz (one
timer interrupt per second) when only a single task is running on a
CPU.
The .config behavior is compatible: existing !CONFIG_NO_HZ and
CONFIG_NO_HZ=y settings get translated to the new values, without the
user having to configure anything. CONFIG_NO_HZ_FULL is turned off by
default.
This feature is based on a lot of infrastructure work that has been
steadily going upstream in the last 2-3 cycles: related RCU support
and non-periodic cputime support in particular is upstream already.
This tree adds the final pieces and activates the feature. The pull
request is marked RFC because:
- it's marked 64-bit only at the moment - the 32-bit support patch is
small but did not get ready in time.
- it has a number of fresh commits that came in after the merge
window. The overwhelming majority of commits are from before the
merge window, but still some aspects of the tree are fresh and so I
marked it RFC.
- it's a pretty wide-reaching feature with lots of effects - and
while the components have been in testing for some time, the full
combination is still not very widely used. That it's default-off
should reduce its regression abilities and obviously there are no
known regressions with CONFIG_NO_HZ_FULL=y enabled either.
- the feature is not completely idempotent: there is no 100%
equivalent replacement for a periodic scheduler/timer tick. In
particular there's ongoing work to map out and reduce its effects
on scheduler load-balancing and statistics. This should not impact
correctness though, there are no known regressions related to this
feature at this point.
- it's a pretty ambitious feature that with time will likely be
enabled by most Linux distros, and we'd like you to make input on
its design/implementation, if you dislike some aspect we missed.
Without flaming us to crisp! :-)
Future plans:
- there's ongoing work to reduce 1Hz to 0Hz, to essentially shut off
the periodic tick altogether when there's a single busy task on a
CPU. We'd first like 1 Hz to be exposed more widely before we go
for the 0 Hz target though.
- once we reach 0 Hz we can remove the periodic tick assumption from
nr_running>=2 as well, by essentially interrupting busy tasks only
as frequently as the sched_latency constraints require us to do -
once every 4-40 msecs, depending on nr_running.
I am personally leaning towards biting the bullet and doing this in
v3.10, like the -rt tree this effort has been going on for too long -
but the final word is up to you as usual.
More technical details can be found in Documentation/timers/NO_HZ.txt"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
sched: Keep at least 1 tick per second for active dynticks tasks
rcu: Fix full dynticks' dependency on wide RCU nocb mode
nohz: Protect smp_processor_id() in tick_nohz_task_switch()
nohz_full: Add documentation.
cputime_nsecs: use math64.h for nsec resolution conversion helpers
nohz: Select VIRT_CPU_ACCOUNTING_GEN from full dynticks config
nohz: Reduce overhead under high-freq idling patterns
nohz: Remove full dynticks' superfluous dependency on RCU tree
nohz: Fix unavailable tick_stop tracepoint in dynticks idle
nohz: Add basic tracing
nohz: Select wide RCU nocb for full dynticks
nohz: Disable the tick when irq resume in full dynticks CPU
nohz: Re-evaluate the tick for the new task after a context switch
nohz: Prepare to stop the tick on irq exit
nohz: Implement full dynticks kick
nohz: Re-evaluate the tick from the scheduler IPI
sched: New helper to prevent from stopping the tick in full dynticks
sched: Kick full dynticks CPU that have more than one task enqueued.
perf: New helper to prevent full dynticks CPUs from stopping tick
perf: Kick full dynticks CPU if events rotation is needed
...
Vitaliy reported that a per cpu HPET timer interrupt crashes the
system during hibernation. What happens is that the per cpu HPET timer
gets shut down when the nonboot cpus are stopped. When the nonboot
cpus are onlined again the HPET code sets up the MSI interrupt which
fires before the clock event device is registered. The event handler
is still set to hrtimer_interrupt, which then crashes the machine due
to highres mode not being active.
See http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=700333
There is no real good way to avoid that in the HPET code. The HPET
code alrady has a mechanism to detect spurious interrupts when event
handler == NULL for a similar reason.
We can handle that in the clockevent/tick layer and replace the
previous functional handler with a dummy handler like we do in
tick_setup_new_device().
The original clockevents code did this in clockevents_exchange_device(),
but that got removed by commit 7c1e76897 (clockevents: prevent
clockevent event_handler ending up handler_noop) which forgot to fix
it up in tick_shutdown(). Same issue with the broadcast device.
Reported-by: Vitaliy Fillipov <vitalif@yourcmc.ru>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Cc: 700333@bugs.debian.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
"Extended nohz" was used as a naming base for the full dynticks
API and Kconfig symbols. It reflects the fact the system tries
to stop the tick in more places than just idle.
But that "extended" name is a bit opaque and vague. Rename it to
"full" makes it clearer what the system tries to do under this
config: try to shutdown the tick anytime it can. The various
constraints that prevent that to happen shouldn't be considered
as fundamental properties of this feature but rather technical
issues that may be solved in the future.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
This way the full nohz CPUs can safely run with the tick
stopped with a guarantee that somebody else is taking
care of the jiffies and GTOD progression.
Once the duty is attributed to a CPU, it won't change. Also that
CPU can't enter into dyntick idle mode or be hot unplugged.
This may later be improved from a power consumption POV. At
least we should be able to share the duty amongst all CPUs
outside the full dynticks range. Then the duty could even be
shared with full dynticks CPUs when those can't stop their
tick for any reason.
But let's start with that very simple approach first.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
[fix have_nohz_full_mask offcase]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Now that timekeeping is protected by its own locks, rename
the xtime_lock to jifffies_lock to better describe what it
protects.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The automatic increase of the min_delta_ns of a clockevents device
should be done in the clockevents code as the minimum delay is an
attribute of the clockevents device.
In addition not all architectures want the automatic adjustment, on a
massively virtualized system it can happen that the programming of a
clock event fails several times in a row because the virtual cpu has
been rescheduled quickly enough. In that case the minimum delay will
erroneously be increased with no way back. The new config symbol
GENERIC_CLOCKEVENTS_MIN_ADJUST is used to enable the automatic
adjustment. The config option is selected only for x86.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20110823133142.494157493@de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (62 commits)
posix-clocks: Check write permissions in posix syscalls
hrtimer: Remove empty hrtimer_init_hres_timer()
hrtimer: Update hrtimer->state documentation
hrtimer: Update base[CLOCK_BOOTTIME].offset correctly
timers: Export CLOCK_BOOTTIME via the posix timers interface
timers: Add CLOCK_BOOTTIME hrtimer base
time: Extend get_xtime_and_monotonic_offset() to also return sleep
time: Introduce get_monotonic_boottime and ktime_get_boottime
hrtimers: extend hrtimer base code to handle more then 2 clockids
ntp: Remove redundant and incorrect parameter check
mn10300: Switch do_timer() to xtimer_update()
posix clocks: Introduce dynamic clocks
posix-timers: Cleanup namespace
posix-timers: Add support for fd based clocks
x86: Add clock_adjtime for x86
posix-timers: Introduce a syscall for clock tuning.
time: Splitout compat timex accessors
ntp: Add ADJ_SETOFFSET mode bit
time: Introduce timekeeping_inject_offset
posix-timer: Update comment
...
Fix up new system-call-related conflicts in
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
arch/x86/kernel/syscall_table_32.S
(name_to_handle_at()/open_by_handle_at() vs clock_adjtime()), and some
due to movement of get_jiffies_64() in:
kernel/time.c
When the per cpu timer is marked CLOCK_EVT_FEAT_C3STOP, then we only
can switch into oneshot mode, when the backup broadcast device
supports oneshot mode as well. Otherwise we would try to switch the
broadcast device into an unsupported mode unconditionally. This went
unnoticed so far as the current available broadcast devices support
oneshot mode. Seth unearthed this problem while debugging and working
around an hpet related BIOS wreckage.
Add the necessary check to tick_is_oneshot_available().
Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1102252231200.2701@localhost6.localdomain6>
Cc: stable@kernel.org # .21 ->
All callers of do_timer() are converted to xtime_update(). The only
users of xtime_lock are in kernel/time/. Make both local to
kernel/time/ and remove them from the global header files.
[ tglx: Reuse tick-internal.h instead of creating another local header
file. Massaged changelog ]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: johnstul@us.ibm.com
Cc: yong.zhang0@gmail.com
Cc: hch@infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__get_cpu_var() can be replaced with this_cpu_read and will then use a
single read instruction with implied address calculation to access the
correct per cpu instance.
However, the address of a per cpu variable passed to __this_cpu_read()
cannot be determined (since it's an implied address conversion through
segment prefixes). Therefore apply this only to uses of __get_cpu_var
where the address of the variable is not used.
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hughd@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
