No need for else after return.
Link: https://lore.kernel.org/r/20200910074843.217661-2-damien.lemoal@wdc.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Boot occasionally fails with some Samsung low-power UFS devices. The reason
is that these devices have a little bit higher latency for NOP OUT
responses. This causes boot to fail because the NOP OUT command is issued
during initialization to check whether the device transport protocol is
ready or not. Increase NOP_OUT_TIMEOUT value from 30 to 50ms.
Link: https://lore.kernel.org/r/231786897.01599016081767.JavaMail.epsvc@epcpadp2
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to compute modulo. A simple comparison is good enough.
Link: https://lore.kernel.org/r/20200911180057.14633-1-thenzl@redhat.com
Acked-by: sreekanth reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
_base_process_reply_queue() called from _base_interrupt() may schedule a
new irq poll. Fix this by calling synchronize_irq() first.
Also ensure that enable_irq() is called only when necessary to avoid
"Unbalanced enable for IRQ..." errors.
Link: https://lore.kernel.org/r/20200910142126.8147-1-thenzl@redhat.com
Fixes: 320e77acb3 ("scsi: mpt3sas: Irq poll to avoid CPU hard lockups")
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will throw an error message when a tampered type controller
is detected. The intent is to avoid interacting with any firmware
which is not secured/signed by Broadcom. Any tampering on firmware
component will be detected by hardware and it will be communicated to
the driver to avoid any further interaction with that component.
[mkp: switched back to dev_err]
Link: https://lore.kernel.org/r/20200814130426.2741171-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following sparse warning:
drivers/scsi/megaraid/megaraid_sas_base.c:80:5: warning: symbol
'smp_affinity_enable' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200915083948.2826598-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable ret has been initialized with a value '0'. The assignment in
switch-case is redundant. Remove it.
Link: https://lore.kernel.org/r/20200914023207.113792-1-jingxiangfeng@huawei.com
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing commit 936e6b85da ("scsi: zfcp: Fix panic on ERP timeout
for previously dismissed ERP action"), I stumbled over
zfcp_fsf_req_complete() and wondered whether it has similar issues wrt
concurrent modification of req->erp_action by
zfcp_erp_strategy_check_fsfreq().
But a closer look shows that both its two callers [zfcp_fsf_reqid_check(),
zfcp_fsf_req_dismiss_all()] remove the request from the adapter's req_list
under the req_list's lock. Hence we can trust that if
zfcp_erp_strategy_check_fsfreq() concurrently looks up the corresponding
req_id, it won't find this request and is thus unable to modify it while
it's being processed by zfcp_fsf_req_complete().
Add a code comment that hopefully makes this easier for future readers, and
condense the two accesses to ->erp_action that made me trip over this code
path in the first place.
Link: https://lore.kernel.org/r/c500eac301fcbba5af942bbd200f2d6b14e46994.1599765652.git.bblock@linux.ibm.com
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the right helper to avoid poking around in the list's internals.
Link: https://lore.kernel.org/r/ed669555c73aab95b29444c10066f492c0c43391.1599765652.git.bblock@linux.ibm.com
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/libfc/fc_disc.c:304
fc_disc_error() warn: passing zero to 'PTR_ERR'
fp may be NULL in fc_disc_error(), use PTR_ERR_OR_ZERO to handle this.
Link: https://lore.kernel.org/r/20200909135432.36772-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following coccinelle warning:
drivers/scsi/fnic/fnic_main.c:446:2-3: Unneeded semicolon
Link: https://lore.kernel.org/r/20200911091057.2938685-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following coccinelle warning:
drivers/scsi/nsp32.c:1250:4-5: Unneeded semicolon
drivers/scsi/nsp32.c:1842:2-3: Unneeded semicolon
Link: https://lore.kernel.org/r/20200911091049.2938158-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following coccinelle warning:
drivers/scsi/sym53c8xx_2/sym_fw.c:372:3-4: Unneeded semicolon
drivers/scsi/sym53c8xx_2/sym_fw.c:480:3-4: Unneeded semicolon
drivers/scsi/sym53c8xx_2/sym_fw.c:536:2-3: Unneeded semicolon
Link: https://lore.kernel.org/r/20200911091031.2937834-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following coccinelle warning:
drivers/scsi/qla2xxx/qla_init.c:7112:5-9: Unneeded variable: "rval".
Return "QLA_SUCCESS" on line 7115
Link: https://lore.kernel.org/r/20200911091021.2937708-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Intel host controllers support the setting of latency tolerance.
Accordingly, implement the PM QoS ->set_latency_tolerance() callback. The
raw register values are also exposed via debugfs.
Link: https://lore.kernel.org/r/20200827072030.24655-1-adrian.hunter@intel.com
Fixes: 8c09d75276 ("scsi: ufshdc-pci: Add Intel PCI IDs for EHL")
Fixes: 1ab27c9cf8 ("ufs: Add support for clock gating")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
not used [-Wunused-but-set-variable]
struct lpfc_sli4_hdw_queue *qp;
^
Link: https://lore.kernel.org/r/20200909082716.37787-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/lpfc/lpfc_debugfs.c: In function ‘lpfc_debugfs_hdwqstat_data’:
drivers/scsi/lpfc/lpfc_debugfs.c:1699:30: warning: variable ‘qp’ set but
This addresses the following gcc warning with "make W=1":
drivers/scsi/gdth.c: In function ‘gdth_async_event’:
drivers/scsi/gdth.c:3010:9: warning: variable ‘cmd_index’ set but not
used [-Wunused-but-set-variable]
int cmd_index;
Link: https://lore.kernel.org/r/20200909082627.101984-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
drivers/scsi/pmcraid.c: In function ‘pmcraid_abort_cmd’:
drivers/scsi/pmcraid.c:2863:33: warning: variable ‘res’ set but not
used [-Wunused-but-set-variable]
struct pmcraid_resource_entry *res;
^
Link: https://lore.kernel.org/r/20200909082627.101984-2-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
drivers/scsi/qla1280.c: In function ‘qla1280_status_entry’:
drivers/scsi/qla1280.c:3607:28: warning: variable ‘lun’ set but not used
[-Wunused-but-set-variable]
3607 | unsigned int bus, target, lun;
| ^~~
drivers/scsi/qla1280.c:3607:20: warning: variable ‘target’ set but not
used [-Wunused-but-set-variable]
3607 | unsigned int bus, target, lun;
| ^~~~~~
drivers/scsi/qla1280.c:3607:15: warning: variable ‘bus’ set but not used
[-Wunused-but-set-variable]
3607 | unsigned int bus, target, lun;
| ^~~
Link: https://lore.kernel.org/r/20200907074518.2326360-5-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
drivers/scsi/qla1280.c: In function ‘qla1280_mailbox_command’:
drivers/scsi/qla1280.c:2430:11: warning: variable ‘data’ set but not
used [-Wunused-but-set-variable]
2430 | uint16_t data;
| ^~~~
Link: https://lore.kernel.org/r/20200907074518.2326360-4-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
drivers/scsi/qla1280.c: In function ‘qla1280_nvram_config’:
drivers/scsi/qla1280.c:2188:36: warning: variable ‘ddma_conf’ set but
not used [-Wunused-but-set-variable]
2188 | uint16_t hwrev, cfg1, cdma_conf, ddma_conf;
| ^~~~~~~~~
Link: https://lore.kernel.org/r/20200907074518.2326360-3-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
drivers/scsi/qla1280.c: In function ‘qla1280_done’:
drivers/scsi/qla1280.c:1244:19: warning: variable ‘lun’ set but not used
[-Wunused-but-set-variable]
1244 | int bus, target, lun;
| ^~~
Link: https://lore.kernel.org/r/20200907074518.2326360-2-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With !CONFIG_OF and SCSI_UFS_EXYNOS selected, the below warning is given:
WARNING: unmet direct dependencies detected for PHY_SAMSUNG_UFS
Depends on [n]: OF [=n] && (ARCH_EXYNOS || COMPILE_TEST [=y])
Selected by [y]:
- SCSI_UFS_EXYNOS [=y] && SCSI_LOWLEVEL [=y] && SCSI [=y] && SCSI_UFSHCD_PLATFORM [=y] && (ARCH_EXYNOS || COMPILE_TEST [=y])
Fix it by removing PHY_SAMSUNG_UFS dependency.
Link: https://lore.kernel.org/r/20200721172021.28922-1-alim.akhtar@samsung.com
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return error code PTR_ERR() from the error handling case instead of
0.
Link: https://lore.kernel.org/r/20200907083949.154251-1-jingxiangfeng@huawei.com
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix build warnings with make W=1 as below,
1.
>> drivers/scsi/ufs/ufs-mediatek.c:116:22: warning: format '%d' expects
>> argument of type 'int', but argument 4 has type 'long int'
2.
CC [M] drivers/scsi/ufs/ufs-mediatek.o
../drivers/scsi/ufs/ufs-mediatek.c:749: error: Cannot parse struct or union!
/** is used specifically with kernel-doc tool.
As a quick fix by removing dubious /** in the comment block of
struct ufs_hba_variant_ops ufs_hba_mtk_vops.
Link: https://lore.kernel.org/r/20200910013756.11385-1-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It was observed on an ISP8324 16Gb HBA with fw=8.08.203 (d0d5) in a
PowerPC64 machine that pkt->entry_type was MBX_IOCB_TYPE/0x39 with an
sp->type SRB_SCSI_CMD which is invalid and should not be possible.
Reading the entry_type from the crash dump shows the expected value of
STATUS_TYPE/0x03 but the call trace shows that qla24xx_mbx_iocb_entry() is
used.
Add a check to verify for consistency and reset the HBA if an invalid state
is reached. Obviously, this is only a workaround until the real problem is
solved.
Link: https://lore.kernel.org/r/20200908081516.8561-5-dwagner@suse.de
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 7c3df1320e ("[SCSI] qla2xxx: Code changes to support new dynamic
logging infrastructure.") removed the use of the func argument. Let's add
it back.
Link: https://lore.kernel.org/r/20200908081516.8561-4-dwagner@suse.de
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Refactor qla2x00_get_sp_from_handle() to avoid the unnecessary goto if
early returns are used. With this we can also avoid preinitialzing the sp
pointer.
Link: https://lore.kernel.org/r/20200908081516.8561-3-dwagner@suse.de
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Emit a warning when ->done or ->free are called on an already freed
srb. There is a hidden use-after-free bug in the driver which corrupts
the srb memory pool which originates from the cleanup callbacks.
An extensive search didn't bring any lights on the real problem. The
initial fix was to set both pointers to NULL and try to catch invalid
accesses. But instead the memory corruption was gone and the driver
didn't crash. Since not all calling places check for NULL pointer, add
explicitly default handlers. With this we workaround the memory
corruption and add a debug help.
Link: https://lore.kernel.org/r/20200908081516.8561-2-dwagner@suse.de
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In sas_notify_lldd_dev_found(), if we can't allocate the necessary
resources, then it seems like the wrong thing to mark the device as found
and to increment the reference count. None of the callers ever drop the
reference in that situation.
[mkp: tweaked commit desc based on feedback from John]
Link: https://lore.kernel.org/r/20200905125836.GF183976@mwanda
Fixes: 735f7d2fed ("[SCSI] libsas: fix domain_device leak")
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During recovery due to FCoE fn ramrod failure we wait for 2 sec and then
call qed->probe. If probe fails then retry max 10 times.
Link: https://lore.kernel.org/r/20200907121443.5150-8-jhasan@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On fan failure, disable the PCI function and initiate recovery for ramrod
failure.
Link: https://lore.kernel.org/r/20200907121443.5150-7-jhasan@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SUCCESS is not returned, error handling will escalate. Return SUCCESS
similar to other conditions in this function.
Link: https://lore.kernel.org/r/20200907121443.5150-6-jhasan@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware expects E_D_TOV field in connection offload parameters as “msec”.
Earlier incorrect value (100ms), was leading to abort from driver in the
case when data frames for read take more than 100ms from target side,
resulting in firmware reporting E_D_TOV expiration.
Link: https://lore.kernel.org/r/20200907121443.5150-4-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct the misleading comment in qedf_initiate_els().
Link: https://lore.kernel.org/r/20200907121443.5150-3-jhasan@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the debug parameter permission to read & write. Gives flexibility
to change the debug verbosity dynamically.
Link: https://lore.kernel.org/r/20200907121443.5150-2-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Forcibly leave UniPro low-power mode if UIC commands failed. This makes
hba_enable_delay_us as correct (default) value for re-enabling the host.
At the same time, change type of parameter "lpm" in function
ufs_mtk_unipro_set_pm() to "bool".
Link: https://lore.kernel.org/r/20200908064507.30774-4-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simply add HOST_PA_TACTIVATE quirk back since it was incorrectly removed
before.
Link: https://lore.kernel.org/r/20200908064507.30774-3-stanley.chu@mediatek.com
Fixes: 47d054580a ("scsi: ufs-mediatek: fix HOST_PA_TACTIVATE quirk for Samsung UFS Devices")
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some MediaTek platforms does not have to bind MPHY so users shall not see
any unnecessary logs. Simply remove logs for this case.
Link: https://lore.kernel.org/r/20200908064507.30774-2-stanley.chu@mediatek.com
Fixes: fc4983018f ("scsi: ufs-mediatek: Allow unbound mphy")
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error recovery is handled by management firmware (MFW) with the help of
qed/qedi drivers. Upon detecting errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.
Link: https://lore.kernel.org/r/20200908095657.26821-9-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support to initiate MFW process recovery for all the devices if storage
function receives the event first.
Also added fix for kernel test robot warning,
>> drivers/scsi/qedi/qedi_main.c:1119:6: warning: no previous prototype
>> for 'qedi_schedule_hw_err_handler' [-Wmissing-prototypes]
Link: https://lore.kernel.org/r/20200908095657.26821-8-mrangankar@marvell.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For short time cable pulls, the in-flight I/O to the firmware is never
cleaned up, resulting in the behaviour of stale I/O completion causing
list_del corruption and soft lockup of the system.
On link down event, mark all the connections for recovery, causing cleanup
of all the in-flight I/O immediately.
Link: https://lore.kernel.org/r/20200908095657.26821-7-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Protect active command list for non-I/O commands like login response,
logout response, text response, and recovery cleanup of active list to
avoid list corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-5-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
