This reverts commit 82f4b67f01.
According to a subsequent revert in the vendor kernel, the original
change was based on unclear documentation and was in fact incorrect.
Emprically, my board's HS200 eMMC at 200MHZ apparently gets lucky with a
phase where this had no impact, but limiting max-frequency to 150MHz to
match the nominal capability of the I/O pins made it virtually unusable,
constantly throwing errors and retuning. With this revert, it starts
behaving perfectly at 150MHz too.
Fixes: 82f4b67f01 ("clk: rockchip: fix wrong mmc sample phase shift for rk3328")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/c80eb52e34c03f817586b6b7912fbd4e31be9079.1589475794.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit 1627f68363 ("clk: rockchip: Handle clock tree for rk3288w variant")
added the check for rk3288w-specific clock-tree changes but in turn would
require a double-compatible due to re-using the main rockchip,rk3288-cru
compatible as entry point.
The binding change actually describes the compatibles as one or the other
so adapt the code accordingly and add a real second entry-point for the
clock controller.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # rock-pi-n8
Link: https://lore.kernel.org/r/20200703154948.260369-1-heiko@sntech.de
The revision rk3288w has a different clock tree about "hclk_vio"
clock, according to the BSP kernel code.
This patch handles this difference by detecting which device-tree
we are using. If it is a "rockchip,rk3288-cru", let's register
the clock tree as it was before. If the device-tree node is
"rockchip,rk3288w-cru", we will apply the difference with this
version of this SoC.
Noticed that this new device-tree compatible must be handled in
bootloader such as u-boot.
Signed-off-by: Mylène Josserand <mylene.josserand@collabora.com>
Link: https://lore.kernel.org/r/20200602080644.11333-2-mylene.josserand@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3036 pll type exposes its lock status in both its pllcon registers
as well as the General Register Files. To remove one dependency convert
it to the "internal" lock status, similar to how rk3399 handles it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200129163821.1547295-3-heiko@sntech.de
Instead of open coding the polling of the lock status, use the
handy regmap_read_poll_timeout for this. As the pll locking is
normally blazingly fast and we don't want to incur additional
delays, we're not doing any sleeps similar to for example the imx
clk-pllv4 and define a very safe but still short timeout of 1ms.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200129163821.1547295-2-heiko@sntech.de
Instead of open coding the polling of the lock status, use the handy
readl_relaxed_poll_timeout for this. As the pll locking is normally
blazingly fast and we don't want to incur additional delays, we're
not doing any sleeps similar to for example the imx clk-pllv4
and define a very safe but still short timeout of 1ms.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200129163821.1547295-1-heiko@sntech.de
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
These aren't used and the macros that reference them aren't used either.
Remove the dead code to avoid compile warnings.
Cc: Owen Chen <owen.chen@mediatek.com>
Cc: Mars Cheng <mars.cheng@mediatek.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Fixes: 1aca9939bf ("clk: mediatek: Add MT6765 clock support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200609211847.27366-1-sboyd@kernel.org
The variable divider is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200602172435.70282-1-colin.king@canonical.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is a spelling mistake in a pr_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200602121030.39132-1-colin.king@canonical.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
I got a build failure with CONFIG_ARCH_SPRD=m when the
main portion of the clock driver failed to get linked into
the kernel:
ERROR: modpost: "sprd_pll_sc_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_pll_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_div_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_comp_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_mux_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_sc_gate_ops" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_clk_probe" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_clk_regmap_init" [drivers/clk/sprd/sc9863a-clk.ko] undefined!
ERROR: modpost: "sprd_pll_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
ERROR: modpost: "sprd_div_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
ERROR: modpost: "sprd_mux_ops" [drivers/clk/sprd/sc9860-clk.ko] undefined!
This is a combination of two trivial bugs:
- A platform should not be 'tristate', it should be a 'bool' symbol
like the other platforms, if only for consistency, and to avoid
surprises like this one.
- The clk Makefile does not traverse into the sprd subdirectory
if the platform is disabled but the drivers are enabled for
compile-testing.
Fixing either of the two would be sufficient to address the link failure,
but for correctness, both need to be changed.
Fixes: 2b1b799d76 ("arm64: change ARCH_SPRD Kconfig to tristate")
Fixes: d41f59fd92 ("clk: sprd: Add common infrastructure")
Acked-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in
the struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
* Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
* Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
* Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
* Fix wrong compatible binding in the qcom driver (Ansuel Smith).
* Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
* Add r8a7742 SoC support to the dt cpufreq driver (Lad Prabhakar).
- Update cpuidle core and drivers:
* Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
* Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
* Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver
and remove an unused local MSR definition from it (Jacob Pan,
Sumeet Pawnikar).
- Update devfreq core and drivers:
* Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
* Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
* Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl7VGjwSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRx46gP/jGAXlddFEQswi6qUT3Cff0A9mb8CdcX
dyKrjX4xxo/wtBIAwSN4achxrgse//ayo2dYTzWRDd31W9Azbv+5F+46XsDRz4hL
pH29u/E66NMtFWnHCmt78NEJn0FzSa0YBC43ZzwFwKktCK9skYIpGN2z6iuXUBSX
Q5GHqop3zvDsdKQFBGL62xvUw/AmOTPG7ohIZvqWBN2mbOqEqMcoFHT+aUF/NbLj
+i14dvTH767eDZGRVASmXWQyljjaRWm+SIw4+m8zT1D1Y3d5IFObuMN+9RQl1Tif
BYjkgJ2oDDMhCJLW7TBuJB+g7exiyaSQds3nMr2ZR+eZbJipICjU4eehNEKIUopU
DM17tHQfnwZfS/7YbCx3vYQwLkNq37AJyXS9uqCAIFM+0n4xN4/mIVmgWYISLDTs
1v9olFxtwMRNpjGGQWPJAO7ebB8Zz9qhQv7pIkSQEfwp93/SzvlVf4vvruTeFN9J
qqG60cDumXWAm+s43eQHJNn5nOd5ocWv0FBpo/cxqKbzxFVWwdB42Cm0SY+rK2ID
uHdnc2DJcK2c78UVbz3Cmk4272foJt2zxchqjFXXAZPLrOsFfzmti4B28VxGxjmP
LG3MhH5sdbF4yl/1aSC1Bnrt+PV9Lus6ut/VKhjwIpw8cqiXgpwSbMoDoaBd9UMQ
ubGz2rplGAtB
=APdj
-----END PGP SIGNATURE-----
Merge tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the system-wide PM driver flags, make runtime switching
of cpuidle governors easier, improve the user space hibernation
interface code, add intel-speed-select interface documentation, add
more debug messages to the ACPI code handling suspend to idle, update
the cpufreq core and drivers, fix a minor issue in the cpuidle core
and update two cpuidle drivers, improve the PM-runtime framework,
update the Intel RAPL power capping driver, update devfreq core and
drivers, and clean up the cpupower utility.
Specifics:
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in the
struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
- Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
- Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
- Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
- Fix wrong compatible binding in the qcom driver (Ansuel Smith).
- Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
- Add r8a7742 SoC support to the dt cpufreq driver (Lad
Prabhakar).
- Update cpuidle core and drivers:
- Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
- Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
- Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver and
remove an unused local MSR definition from it (Jacob Pan, Sumeet
Pawnikar).
- Update devfreq core and drivers:
- Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
- Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
- Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei)"
* tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (51 commits)
cpuidle: Fix three reference count leaks
PM: runtime: Replace pm_runtime_callbacks_present()
PM / devfreq: Use lockdep asserts instead of manual checks for locked mutex
PM / devfreq: imx-bus: Fix inconsistent IS_ERR and PTR_ERR
PM / devfreq: Replace strncpy with strscpy
PM / devfreq: imx: Register interconnect device
PM / devfreq: Add generic imx bus scaling driver
PM / devfreq: tegra30: Delete an error message in tegra_devfreq_probe()
PM / devfreq: tegra30: Make CPUFreq notifier to take into account boosting
PM: hibernate: Restrict writes to the resume device
PM: runtime: clk: Fix clk_pm_runtime_get() error path
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
ACPI: EC: PM: s2idle: Extend GPE dispatching debug message
ACPI: PM: s2idle: Print type of wakeup debug messages
powercap: RAPL: remove unused local MSR define
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
Documentation: admin-guide: pm: Document intel-speed-select
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
Documentation: ABI: make current_governer_ro as a candidate for removal
...
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for Qualcomm's MSM8939 Generic Clock Controller
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
* clk-mmp:
clk: mmp2: Add audio clock controller driver
dt-bindings: clock: Add Marvell MMP Audio Clock Controller binding
clk: mmp2: Add support for power islands
dt-bindings: marvell,mmp2: Add ids for the power domains
dt-bindings: clock: Make marvell,mmp2-clock a power controller
clk: mmp2: Add the audio clock
clk: mmp2: Add the I2S clocks
clk: mmp2: Rename mmp2_pll_init() to mmp2_main_clk_init()
clk: mmp2: Move thermal register defines up a bit
dt-bindings: marvell,mmp2: Add clock id for the Audio clock
dt-bindings: marvell,mmp2: Add clock id for the I2S clocks
clk: mmp: frac: Allow setting bits other than the numerator/denominator
clk: mmp: frac: Do not lose last 4 digits of precision
* clk-intel:
clk: intel: remove redundant initialization of variable rate64
clk: intel: Add CGU clock driver for a new SoC
dt-bindings: clk: intel: Add bindings document & header file for CGU
* clk-ingenic:
clk: ingenic: Mark ingenic_tcu_of_match as __maybe_unused
clk: X1000: Add FIXDIV for SSI clock of X1000.
dt-bindings: clock: Add and reorder ABI for X1000.
clk: Ingenic: Add CGU driver for X1830.
dt-bindings: clock: Add X1830 clock bindings.
clk: Ingenic: Adjust cgu code to make it compatible with X1830.
clk: Ingenic: Remove unnecessary spinlock when reading registers.
* clk-qcom:
clk: qcom: Add missing msm8998 ufs_unipro_core_clk_src
dt-bindings: clock: Add YAML schemas for QCOM A53 PLL
clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller
clk: qcom: gcc: Add support for Secure control source clock
dt-bindings: clock: Add gcc_sec_ctrl_clk_src clock ID
clk: qcom: gcc: Add support for a new frequency for SC7180
clk: qcom: Add DT bindings for MSM8939 GCC
clk: qcom: gcc: Add missing UFS clocks for SM8150
clk: qcom: gcc: Add GPU and NPU clocks for SM8150
clk: qcom: mmcc-msm8996: Properly describe GPU_GX gdsc
clk: qcom: gdsc: Handle GDSC regulator supplies
clk: qcom: msm8916: Fix the address location of pll->config_reg
* clk-silabs:
clk: clk-si5341: Add support for the Si5345 series
- Allow the COMMON_CLK config to be selectable
* clk-selectable:
clk: Move HAVE_CLK config out of architecture layer
MIPS: Loongson64: Drop asm/clock.h include
ARM: mmp: Remove legacy clk code
clk: Allow the common clk framework to be selectable
mmc: meson-mx-sdio: Depend on OF_ADDRESS and not just OF
MIPS: Remove redundant CLKDEV_LOOKUP selects
h8300: Remove redundant CLKDEV_LOOKUP selects
arm64: tegra: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant COMMON_CLK selects
* clk-amlogic:
clk: meson: meson8b: Don't rely on u-boot to init all GP_PLL registers
clk: meson: meson8b: Make the CCF use the glitch-free VPU mux
clk: meson: meson8b: Fix the vclk_div{1, 2, 4, 6, 12}_en gate bits
clk: meson: meson8b: Fix the polarity of the RESET_N lines
clk: meson: meson8b: Fix the first parent of vid_pll_in_sel
clk: meson: g12a: Prepare the GPU clock tree to change at runtime
clk: meson: gxbb: Prepare the GPU clock tree to change at runtime
clk: meson: meson8b: make the hdmi_sys clock tree mutable
clk: meson8b: export the HDMI system clock
* clk-renesas:
dt-bindings: clock: renesas: mstp: Convert to json-schema
dt-bindings: clock: renesas: div6: Convert to json-schema
clk: renesas: cpg-mssr: Fix STBCR suspend/resume handling
clk: renesas: rcar-gen2: Remove superfluous CLK_RENESAS_DIV6 selects
clk: renesas: cpg-mssr: Add R8A7742 support
dt-bindings: clock: renesas: cpg-mssr: Document r8a7742 binding
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
MAINTAINERS: Add DT Bindings for Renesas Clock Generators
clk: renesas: r9a06g032: Fix some typo in comments
dt-bindings: clock: renesas: rcar-usb2-clock-sel: Add r8a77961 support
* clk-samsung:
clk: samsung: exynos5433: Add IGNORE_UNUSED flag to sclk_i2s1
ARM/SAMSUNG EXYNOS ARM ARCHITECTURES: Use fallthrough;
clk: samsung: Fix CLK_SMMU_FIMCL3 clock name on Exynos542x
clk: samsung: Mark top ISP and CAM clocks on Exynos542x as critical
* clk-allwinner:
clk: sunxi: Fix incorrect usage of round_down()
Nearly each Baikal-T1 IP-core is supposed to have a clock source
of particular frequency. But since there are greater than five
IP-blocks embedded into the SoC, the CCU PLLs can't fulfill all the
needs. Baikal-T1 CCU provides a set of fixed and configurable clock
dividers in order to generate a necessary signal for each chip
sub-block.
This driver creates the of-based hardware clocks for each divider
available in Baikal-T1 CCU. The same way as for PLLs we split the
functionality up into the clocks operations (gate, ungate, set rate,
etc) and hardware clocks declaration/registration procedures.
In accordance with the CCU documentation all its dividers are distributed
into two CCU sub-blocks: AXI-bus and system devices reference clocks.
The former sub-block is used to supply the clocks for AXI-bus interfaces
(AXI clock domains) and the later one provides the SoC IP-cores reference
clocks. Each sub-block is represented by a dedicated DT node, so they
have different compatible strings to distinguish one from another.
For some reason CCU provides the dividers of different types. Some
dividers can be gateable some can't, some are fixed while the others
are variable, some have special divider' limitations, some've got a
non-standard register layout and so on. In order to cover all of these
cases the hardware clocks driver is designed with an info-descriptor
pattern. So there are special static descriptors declared for the
dividers of each type with additional flags describing the block
peculiarity. These descriptors are then used to create hardware clocks
with proper operations.
Some CCU dividers provide a way to reset a domain they generate
a clock for. So the CCU AXI-bus and CCU system devices clock
drivers also perform the reset controller registration.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200526222056.18072-5-Sergey.Semin@baikalelectronics.ru
[sboyd@kernel.org: Drop return from void function, silence sparse
warnings about initializing structs with NULL vs. integer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Baikal-T1 is supposed to be supplied with a high-frequency external
oscillator. But in order to create signals suitable for each IP-block
embedded into the SoC the oscillator output is primarily connected to
a set of CCU PLLs. There are five of them to create clocks for the MIPS
P5600 cores, an embedded DDR controller, SATA, Ethernet and PCIe domains.
The last three domains though named by the biggest system interfaces in
fact include nearly all of the rest SoC peripherals. Each of the PLLs is
based on True Circuits TSMC CLN28HPM IP-core with an interface wrapper
(so called safe PLL' clocks switcher) to simplify the PLL configuration
procedure.
This driver creates the of-based hardware clocks to use them then in
the corresponding subsystems. In order to simplify the driver code we
split the functionality up into the PLLs clocks operations and hardware
clocks declaration/registration procedures.
Even though the PLLs are based on the same IP-core, they may have some
differences. In particular, some CCU PLLs support the output clock change
without gating them (like CPU or PCIe PLLs), while the others don't, some
CCU PLLs are critical and aren't supposed to be gated. In order to cover
all of these cases the hardware clocks driver is designed with an
info-descriptor pattern. So there are special static descriptors declared
for each PLL, which is then used to create a hardware clock with proper
operations. Additionally debugfs-files are provided for each PLL' field
to make sure the implemented rate-PLLs-dividers calculation algorithm is
correct.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200526222056.18072-4-Sergey.Semin@baikalelectronics.ru
[sboyd@kernel.org: Silence sparse warning about initializing structs
with NULL vs. integer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CONFIG_ICST is for ARM Ltd reference platforms and isn't used by Zynq
platform, so remove selecting it. It appears to be a copy-n-paste error.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
[arnd: remove the versatile clk driver change I added previously]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When some new clock supports are introduced, e.g. [1]
it might lead to an error although it should be NULL because
clk_init_data is on the stack and it might have random values
if using without initialization.
Add the missing initial value to clk_init_data.
[1] https://android-review.googlesource.com/c/kernel/common/+/1278046
Fixes: a3ae549917 ("clk: mediatek: Add new clkmux register API")
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1590560749-29136-1-git-send-email-weiyi.lu@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the Si5342, Si5344 and Si5345 chips. These are equivalent
to the Si5341 family, but with more clock input options (which are not
supported yet by this driver).
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lkml.kernel.org/r/20200507061544.11388-1-mike.looijmans@topic.nl
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ufs_unipro_core_clk_src is required to allow UFS to clock scale for power
savings.
Fixes: b5f5f525c5 ("clk: qcom: Add MSM8998 Global Clock Control (GCC) driver")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20200528142205.44003-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This device id table is passed to of_match_node() later on in probe, but
on CONFIG_OF=n builds of_match_node() doesn't do anything with the
arguments. Lets just mark the table unused so that the compiler doesn't
complain about this.
drivers/clk/ingenic/tcu.c:326:34: warning: unused variable 'ingenic_tcu_of_match' [-Wunused-const-variable]
static const struct of_device_id ingenic_tcu_of_match[] __initconst = {
^
1 warning generated.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200528233837.70269-1-sboyd@kernel.org
1.The SSI clock of X1000 not like JZ4770 and JZ4780, they are not
directly derived from the output of SSIPLL, but from the clock
obtained by dividing the frequency by 2. "X1000_CLK_SSIPLL_DIV2"
is added for this purpose, and ensure that it initialized before
"X1000_CLK_SSIMUX" when initializing the clocks.
2.Clocks of LCD, OTG, EMC, EFUSE, OST, TCU, and gates of CPU, PCLK
are also added.
3.Use "CLK_OF_DECLARE_DRIVER" like the other CGU drivers.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-8-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the clocks provided by the CGU in the Ingenic X1830
SoC, making use of the cgu code to do the heavy lifting.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-6-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PLL of X1830 Soc from Ingenic has been greatly changed,
the bypass control is placed in another register, so now two
registers may needed to control the PLL. To this end, a new
"bypass_reg" was introduced. In addition, when calculating
rate, the PLL of X1830 introduced an extra 2x multiplier,
so a new "rate_multiplier" was introduced. And adjust the
code in jz47xx-cgu.c and x1000-cgu.c, make it to be
compatible with the new cgu code.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It is not necessary to use spinlock when reading registers,
so remove it from cgu.c.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The variable rate64 is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lkml.kernel.org/r/20200528221219.535804-1-colin.king@canonical.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a driver for a block that generates master and bit clocks for
the I2S interface. It's separate from the PMUs that generate clocks for
the peripherals.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-14-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Apart from the clocks and resets, the PMU hardware also controls power
to peripherals that are on separate power islands. On MMP2, that's the
GC860 GPU and the SSPA audio interface, while on MMP3 also the camera
interface is on a separate island, along with the pair of GC2000 and GC300
GPUs and the SSPA.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-12-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a trivial rename for a routine that registers more clock sources
than the PLLs -- there's also a XO.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-7-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A trivial change to keep the sorting sane. The APBC registers are happier
when they are grouped together, instead of mixed with the APMU ones.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-6-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For the I2S fractional clocks, there are more bits that need to be set
for the clock to run. Their actual meaning is unknown.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-3-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
While calculating the output rate of a fractional divider clock, the
value is divided and multipled by 10000, discarding the least
significant digits -- presumably to fit the intermediate value within 32
bits.
The precision we're losing is, however, not insignificant for things like
I2S clock. Maybe also elsewhere, now that since commit ea56ad6026 ("clk:
mmp2: Stop pretending PLL outputs are constant") the parent rates are more
precise and no longer rounded to 10000s.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-2-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The latest specs for the AST2600 A1 chip include some different bit
definitions for calculating the AHB clock divider. Implement these in
order to get the correct AHB clock value in Linux.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200408203616.4031-1-eajames@linux.ibm.com
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes an issue leading to having all clocks following a critical
clocks marked as well as criticals.
Fixes: fa6415affe ("clk: st: clk-flexgen: Detect critical clocks")
Signed-off-by: Alain Volmat <avolmat@me.com>
Link: https://lkml.kernel.org/r/20200322140740.3970-1-avolmat@me.com
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
