When setting the affinity of a VPE (either because we map or move
it), make sure the effective affinity is correctly reported back
to the core kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Sending VINVALL to all ITSs is completely pointless, as all
we're trying to achieve is to tell the redistributor that
the property table for this VPE should be invalidated.
Let's issue the command on the first valid ITS and be done with it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we map all VPEs on all ITSs. While this is not wrong,
this is quite a big hammer, as moving a VPE around requires
all ITSs to be synchronized. Needles to say, this is an
expensive proposition.
Instead, let's switch to a mode where we issue VMAPP commands
only on ITSs that are actually involved in reporting interrupts
to the given VM.
For that purpose, we refcount the number of interrupts are are
mapped for this VM on each ITS, performing the map/unmap
operations as required. It then allows us to use this refcount
to only issue VMOVP to the ITSs that need to know about this
VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vmapp operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vinvall operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to make use of the maximum number of ITSs in
a GICv4 system, let's make this value global (and rename it to
GICv4_ITS_LIST_MAX).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At boot time, we enumerate all the GICv4-capable ITSs, and build
a mask of the available ITSs. Take this opportunity to store
the ITS number in the its_node structure so that we can use it
at a later time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to be able to issue command variants depending on
how broken an ITS is, let's pass the its pointer to all
command building primitives.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the ITS stops processing commands, we're pretty much toasted
as we cannot update the configuration anymore (and we're not
even sure that the ITS still translates interrups).
If that happens, let's dump some basic information about the
state of affairs before moving on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As it turns out, the IIDR is not sufficient to distinguish between GICv3
implementations when it comes to enabling quirks. So update the prototype
of the init() hook to return a bool, and interpret a 'false' return value
as no match, in which case the 'enabling workaround' log message should
not be printed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Before adding another SoC whose device ID space deviates from the
value presented in the GIC ID registers, let's slightly refactor
the code so that the ID registers are probed before that quirks
handling executes. This allows us to move the device ID override
into the quirk handler itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A new feature Range Selector (RS) has been added to GIC specification
in order to support more than 16 CPUs at affinity level 0. New fields
are introduced in SGI system registers (ICC_SGI0R_EL1, ICC_SGI1R_EL1
and ICC_ASGI1R_EL1) to relax an artificial limit of 16 at level 0.
- A new RSS field in ICC_CTLR_EL3, ICC_CTLR_EL1 and ICV_CTLR_EL1:
[18] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
- A new RS field in ICC_SGI0R_EL1, ICC_SGI1R_EL1 and ICC_ASGI1R_EL1:
[47:44] - RangeSelector (RS) which group of 16 TargetList[n] field
TargetList[n] represents aff0 value ((RS*16)+n)
When ICC_CTLR_EL3.RSS==0 or ICC_CTLR_EL1.RSS==0, RS is RES0.
- A new RSS field in GICD_TYPER:
[26] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Added register block offsets to the brcmstb_l2_intc_data structure
for the status and mask registers to support reading the active
interupts in an abstracted way. It seems like an irq_chip method
should have been provided for this, but it's not there yet.
Abstracted the implementation of the handler, suspend, and resume
functions to not use any hard coded register offsets.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Saving the generic chip pointer in the brcmstb_l2_intc_data prevents
the need to call irq_get_domain_generic_chip(). Also don't need to
save parent_irq and base there since local variables in the
brcmstb_l2_intc_of_init() function are just as good.
The handle_edge_irq flow or chained_irq_enter takes care of the
acknowledgment of the interrupt so it is redundant to clear it in
brcmstb_l2_intc_irq_handle().
irq_linear_revmap() is a fast path equivalent of irq_find_mapping()
that is appropriate to use for domain controllers of this type.
Defining irq_mask_ack is slightly more efficient than just
implementing irq_mask and irq_ack separately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the of_device_get_match_data() helper instead of open coding.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a menu for IRQ chip drivers. This makes the Device drivers menu be more
consistent (listing "subsystems" instead of specific options) and makes the
IRQCHIP options be listed in expected places for 'make menu|xconfig'.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/3db7385a-c6a1-5c93-0797-6f4b6b2b2cde@infradead.org
omap_nr_pending and omap_nr_irqs variables are initialized
right at the beginning of intc_of_init function, so there's
no need to statically initialize them.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016161303.veumgcd3xom5c54r@lenoch
All mach-omap2 variants are device tree only now, so this function is dead
code. Remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016160422.uu2i7vvrgy7cc4aw@lenoch
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
The write_gic_smask() & write_gic_rmask() functions take a shared
interrupt number as a parameter, but we're incorrectly providing them a
bitmask with the shared interrupt's bit set. This effectively means that
we mask or unmask the shared interrupt 1<<n rather than shared interrupt
n, and as a result likely drop interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 68898c8765f4 ("irqchip: mips-gic: Drop gic_(re)set_mask() functions")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gcc-4.5 and earlier don't like named initializers for anonymous
union members:
drivers/irqchip/irq-gic-v4.c: In function 'its_map_vlpi':
drivers/irqchip/irq-gic-v4.c:176:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_get_vlpi':
drivers/irqchip/irq-gic-v4.c:192:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_prop_update_vlpi':
drivers/irqchip/irq-gic-v4.c:208:3: error: unknown field 'config' specified in initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c:208:3: error: initialization makes pointer from integer without a cast
This is fairly easy to work around, by using extra curly braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
get_cpu_number() doesn't use existing helper to iterate over possible
CPUs, It will cause an error in case of discontinuous @cpu_possible_mask
such as 0b11110001, which can result from a core having failed to come
up on a SMP machine.
Fixed by using existing helper for_each_possible_cpu().
Signed-off-by: zijun_hu <zijun_hu@htc.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
gic_set_affinity() manually copies the provided cpumask to the struct
irq_common_data affinity field, returning IRQ_SET_MASK_OK_NOCOPY in
order to prevent the core code from doing that.
We can instead simply let the core code do it for us, by returning
IRQ_SET_MASK_OK instead of IRQ_SET_MASK_OK_NOCOPY & doing the copy
ourselves.
[ralf@linux-mips.org: Resolve merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17056/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently in gic_set_affinity() we calculate a temporary cpumask holding
the intersection of the provided cpumask & the CPUs that are online,
then we call cpumask_first twice on it to find the first such CPU. Since
we don't need the temporary cpumask for anything else & we only care
about the first CPU that's both online & in the provided cpumask, we can
instead use cpumask_first_and to find that CPU & drop the temporary
mask.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When parsing mti,reserved-cpu-vectors we generate a mask of all bits
that have been declared reserved, the loop through starting from bit 2
to find one that isn't reserved (ie. is zero).
This patch accomplishes the same task more simply by:
- Inititialising the reserved mask to 0x3 (ie. the 2 software
interrupts). This means we don't need to skip them later as the loop
previously has.
- Replacing the loop checking for zero bits with find_first_zero_bit,
which fits our needs now that the 2 software interrupts are marked
reserved. This requires that the type of reserved is changed to
unsigned long so that it's suitable for use with bitmap functions.
- Replacing the magic number 8 with the hamming weight of the ST0_IM
field - ie. the number of bits that a MIPS CPU has for interrupt
inputs. This is still a compile-time constant 8, but makes it
clearer why it's 8.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch avoids the need to read the GIC_SH_MASK* registers when
decoding shared interrupts by setting & clearing the interrupt's bit in
the appropriate CPU's pcpu_masks entry when masking or unmasking the
interrupt.
This effectively means that whilst an interrupt is masked we clear its
bit in all pcpu_masks, which causes gic_handle_shared_int() to ignore it
on all CPUs without needing to check GIC_SH_MASK*.
In essence, we add a little overhead to masking or unmasking interrupts
but in return reduce the overhead of the far more common task of
decoding interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Define the pcpu_masks variable using the kernel's standard per-cpu
variable support, rather than an open-coded array of structs containing
bitmaps.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gic_basic_init() is now a fairly short function that is only called in
one place. Inline it into gic_of_init() to help readability.
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __gic_init() function is only called from gic_of_init() now that the
non-DT path has been removed. In order to simplify the code & aid
readability, fold __gic_init() into gic_of_init().
This provides us with the ability to return an error code, which
__gic_init() was previously unable to do. As such the irq_domain_add_*()
error paths are modified to print & return an error rather than panic().
[ralf@linux-mips.org: Resoled reject.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17050/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The linux/irqchip/mips-gic.h header is now almost empty. Move the
declarations of gic_get_c0_compare_int(), gic_get_c0_perfcount_int() &
gic_get_c0_fdc_int() to asm/mips-gic.h in order to close in on being
able to delete the former header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing uses the global gic_present variable anymore; mips_gic_present()
should be used instead. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All in-tree platforms now probe the GIC driver using device tree, and as
such nothing calls gic_init() any longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We provide a forward declaration of the __gic_irq_dispatch() function
for no apparent reason. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS VDSO code is no longer reliant upon the irqchip driver to
provide the address of the GIC's user-visible section via
gic_get_usm_range(). Remove the now-dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the definitions of macros used to convert between hardware IRQ
numbers & shared or local interrupt numbers into the irqchip driver,
which is all that should ever need to care about them.
Remove GIC_CPU_TO_VEC_OFFSET() in the process since it's never used.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC VP-local &
VP-other register blocks to use the new accessor functions provided by
asm/mips-gic.h, resulting in code which is often shorter & easier to
read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17036/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the new accessor functions provided by asm/mips-gic.h to access
masks controlling local interrupts, resulting in code which is often
shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC shared register
block to use the new accessor functions provided by asm/mips-gic.h,
resulting in code which is often shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_vpe() function in favour of using the new
write_gic_map_vp() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_pin() function in favour of using the new
write_gic_map_pin() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_dual_edge() function in favour of using the new
change_gic_dual() accessor function which provides equivalent
functionality. This also allows us to remove the gic_update_bits()
function which gic_set_dual_edge() was the last user of, along with the
GIC_INTR_OFS() & GIC_INTR_BIT() macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_trigger() function in favour of using the new
change_gic_trig() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_polarity() function in favour of using the new
change_gic_pol() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gic_set_mask() & gic_reset_mask() functions are now no more
convenient to call than the write_gic_smask() or write_gic_rmask()
accessor functions. Remove the layer of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify gic_local_irq_domain_map() by:
- Moving the check for invalid IRQs outside of the loop.
- Moving the decision about whether to use gic_cpu_pin or timer_cpu_pin
outside of the loop.
- Using the new write_gic_vo_map() accessor function to avoid the need
to handle each map register separately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
