When we are in Wake-on-LAN, we operate with the host sofware not running
a network stack, so we want to the switch to flood packets in order to
cause a system wake-up when matching specific filters (unicast or
multicast). This was not necessary before since we supported Magic
Packet which are targeting a broadcast MAC address which the switch
already floods.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason why we should limit ourselves to matching only full
IPv4 addresses (/32), the same logic applies between the DATA and MASK
ports, so just make it more configurable to accept both.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inserting IPv6 CFP rules complicates the code a little bit in that we
need to insert two rules side by side and chain them to match a full
IPv6 tuple (src, dst IPv6 + port + protocol).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for introducing IPv6 rules support, make the
cfp_udf_layout more flexible and match more accurately how the HW is
designed: we have 3 + 1 slices per protocol, but we may not be using all
of them and we are relative to a particular base offset (slice A for
IPv4 for instance). Also populate the slice number that should be used
(slice 1 for IPv4) based on the lookup function.
Finally, we introduce two helper functions: udf_upper_bits() and
udf_lower_bits() to help setting the UDF_n_* valid bits based on the
number of UDFs valid within a slice. Update the IPv4 rule setting to
make use of it to be more robust wrt. change in number of User Defined
Fields being programmed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open coding the shift for the IP protocol, IP fragment bit
etc. define and/or use existing constants to that end.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on the out of band Advanced Congestion Buffering (ACB) mechanism at
the switch level now that we have properly established the queue mapping
between the switch egress queues and the SYSTEMPORT egress queues. This
allows the switch to correctly backpressure the host system when one of
its queue drops below the configured thresholds.
This is also helping achieve so called "lossless" behavior by adapting
the TX interrupt pacing to the actual speed and capacity of the switch
port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bcm_sf2 EEE-related functions to the b53 driver because this is shared
code amongst Gigabit capable switch, only 5325 and 5365 are too old to support
that.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to enable Broadcom tags/headers is largely switch independent,
and in preparation for enabling it for multiple devices with b53, move
the code we have in bcm_sf2.c to b53_common.c
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Compact Field Processor definitions for the Broadcom Starfighter 2
and compatible versions of the switch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, all traffic goes to queue 0, re-configure the traffic
classes to quality of service mapping such that priority X maps to queue
X, where X is from 0 through 7.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the integrated switch found on BCM7278:
- core_reg_align is set to 1, to force a translation into the target
address space which is 8 bytes aligned
- an alternate SWITCH_REG layout is provided since registers are largely
bit/masks compatible but have different offsets
- conditional for all CORE_STS_OVERRIDE_{IMP,GMII_P} since those got
moved way out of the traditional register space
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting a new device with a slightly different
register layout, affecting the SWITCH_REG and SWITCH_CORE address
spaces, perform a few preparatory steps:
- allow matching the compatible string against a data description
- convert the SWITCH_REG register accesses into an indirection table
- prepare for supporting a SWITCH_CORE register alignment requirement
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are using b53_common for most VLAN, FDB and bridge
operations, delete all the redundant code that we had in bcm_sf2.c to
keep only the integration specific logic that we have to deal with:
power management, link management and the external interfaces (RGMII,
MDIO).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for the VLAN registers that we are going to
manipulate in subsequent patches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.
Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EEE is enabled, negotiate this feature with the PHY and make sure
that the capability checking, local EEE advertisement, link partner EEE
advertisement and auto-negotiation resolution returned by phy_init_eee()
is positive, and enable EEE at the switch level.
While querying the current EEE settings, verify the low-power indication
and indicate its status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated BCM7xxx PHY contains no useful revision information
in its MII_PHYSID2 bits 3:0, that information is instead contained in
the SWITCH_REG_PHY_REVISION register.
Read this register, store its value, and return it by implementing the
dsa_switch::get_phy_flags() callback accordingly. The register layout is
already matching what the BCM7xxx PHY driver is expecting to find.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:
- configuration of the external switch port interface: MII, RevMII,
RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
unused
Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
