Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org> # 4.19: 36156f9241
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses GPIO descriptors only, <linux/of_gpio.h>
is not used so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not use the old GPIO includes so drop
them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports. In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60. Port 6 is the host port.
Setting a zero value can be used to stop port from receiving.
However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate. This does not apply to
multicast and broadcast addresses though. To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.
Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to handle optional reset GPIO in the KSZ switch driver. The switch
has a reset GPIO line which can be controlled by the CPU, so make sure it is
configured correctly in such setups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ksz_9477_reg.h to ksz9477_reg.h for consistency as the product
name is always KSZ####.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other KSZ switch drivers
can access code in ksz_common.c.
Add ksz_spi.h for common functions used by KSZ switch SPI drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions with ksz9477 prefix to separate chip specific code
from common code.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up code according to patch check suggestions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace license with GPL.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize mutex before use. Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.
On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:
b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'
Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.
Fixes: 7a8c7f5c30 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one code block when returning because the interface type is
unsupported and also check if some unsupported port gets configured.
In addition fix a double the and use dsa_is_cpu_port() instated of
manually getting the CPU port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
