Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Continuing the workaround implemented in commit 23665aaf91
("mac80211: Interoperability workaround for 80+80 and 160 MHz channels")
use the same code to parse the Wide Bandwidth Channel Switch element
by converting to VHT Operation element since the spec also just refers
to that for parsing semantics, particularly with the workaround.
While at it, remove some dead code - the IEEE80211_STA_DISABLE_40MHZ
flag can never be set at this point since it's checked earlier and the
wide_bw_chansw_ie pointer is set to NULL if it's set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of handling ADDBA Request while a session
is already active with the peer is wrong - in case the peer is using
the existing session's dialog token this should be treated as update
to the session, which can update the timeout value.
We don't really have a good way of supporting that, so reject, but
implement the required behaviour in the spec of "Even if the updated
ADDBA Request frame is not accepted, the original Block ACK setup
remains active." (802.11-2012 10.5.4)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We normally return an uninitialized value, but no one checks it so it
doesn't matter. Anyway, let's silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
-----BEGIN PGP SIGNATURE-----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=FvhQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds a debugfs entry to read and modify some fq parameters.
This makes it easy to debug, test and experiment.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove module parameter for now]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it a lot easier to understand the capabilities used
by the station:
VHT supported
cap: 0x300819b2
MAX-MPDU-11454
80Mhz
RXLDPC
SHORT-GI-80
TXSTBC
RXSTBC_1
SU-BEAMFORMER-CAPABLE
SU-BEAMFORMEE-CAPABLE
BEAMFORMEE-STS: 0x0
SOUNDING-DIMENSIONS: 0x0
MU-BEAMFORMER-CAPABLE
MPDU-LENGTH-EXPONENT: 0x0
LINK-ADAPTATION-VHT-MRQ-MFB: 0x0
RX-ANTENNA-PATTERN
TX-ANTENNA-PATTERN
RX MCS: fffe
TX MCS: fffe
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The header field is defined as u8[] but also accessed as struct
ieee80211_hdr. Enforce an alignment of 2 to prevent unnecessary
unaligned accesses, which can be very harmful for performance on many
platforms.
Fixes: e495c24731 ("mac80211: extend fast-xmit for more ciphers")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
-----BEGIN PGP SIGNATURE-----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=QNxF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more work for 4.7, notably:
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case that dev_alloc_name() fails, e.g. because the name was
given by the user and already exists, we need to clean up properly
and free the per-CPU statistics. Fix that.
Cc: stable@vger.kernel.org
Fixes: 5a490510ba ("mac80211: use per-CPU TX/RX statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes:
net/mac80211/mesh_hwmp.c:603:26: warning: ‘target_metric’ may be used uninitialized in this function
target_metric is only consumed when reply = true so no bug exists here,
but not all versions of gcc realize it. Initialize to 0 to remove the
warning.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prevents excessive A-MSDU aggregation at low data rates or bad
conditions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises the new HW flag USE_RSS, make the
station statistics on the fast-rx path per-CPU. This will
enable calling the RX in parallel, only hitting locking or
shared cachelines when the fast-RX path isn't available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On 32-bit platforms, the 64-bit counters we keep need to be protected
to be consistently read. Use the u64_stats_sync mechanism to do that.
In order to not end up with overly long lines, refactor the tidstats
assignments a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When storing the last_rate_* values in the RX code, there's nothing
to guarantee consistency, so a concurrent reader could see, e.g.
last_rate_idx on the new value, but last_rate_flag still on the old,
getting completely bogus values in the end.
To fix this, I lifted the sta_stats_encode_rate() function from my
old rate statistics code, which encodes the entire rate data into a
single 16-bit value, avoiding the consistency issue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of touching the rx_stats.last_rx from the status path, introduce
and use a status_stats.last_ack variable. This will make rx_stats.last_rx
indicate when the last frame was received, making it available for real
"last_rx" and statistics gathering; statistics, when done per-CPU, will
need to figure out which place was updated last for those items where the
"last" value is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to update rx_stats.last_rx after allocating
a station since it's already updated during allocation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the averaged values out of rx_stats and into rx_stats_avg,
to cleanly split them out. The averaged ones cannot be supported
for parallel RX in a per-CPU fashion, while the other values can
be collected per CPU and then combined/selected when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the semicolon, people typically assume that and
once line already put a semicolon behind the "call".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the RX MSDU statistics, we need to count the number of
MSDUs created and accepted from an A-MSDU. Right now, all
frames in any A-MSDUs were completely ignored. Fix this by
moving the RX MSDU statistics accounting into the deliver
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep warned of a lock dependency between the mesh_plink lock
and the internal lock for the rhashtable. The problem is that
the rhashtable code uses a spin lock with softirqs enabled, while
mesh_plink_timer executes a walk (to flush paths on a state change)
inside a softirq with the plink lock held.
This leads to the following deadlock if the timer fires while rht
lock is held on this CPU, and plink lock is held on another CPU:
CPU0 CPU1
---- ----
lock(&(&ht->lock)->rlock);
local_irq_disable();
lock(&(&sta->mesh->plink_lock)->rlock);
lock(&(&ht->lock)->rlock);
<Interrupt>
lock(&(&sta->mesh->plink_lock)->rlock);
*** DEADLOCK ***
Fix by waiting until we drop the plink lock to flush paths.
Fixes: d48a1b7cd439 ("mac80211: mesh: convert path table to rhashtable")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several of the mesh path fields are undocumented and some
of the documentation is no longer correct or relevant after
the switch to rhashtable. Clean up the kernel doc
accordingly and reorder some fields to match the structure
layout.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduce padding waste in struct mesh_table and struct rmc_entry by
moving the smaller fields to the end.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we have converted the mesh path tables to rhashtable, we are
no longer swapping out the entire mesh_pathtbl pointer with RCU.
As a result, we no longer need indirection to the hlist head for
the gates list and can simply embed it, saving a pair of
pointer-sized allocations.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RMC cache has 256 list heads plus a u32, which puts it at the
unfortunate size of 4104 bytes with padding. kmalloc() will then
round this up to the next power-of-two, so we wind up actually
using two pages here where most of the second is wasted.
Switch to hlist heads here to reduce the structure size down to
fit within a page.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely case that mesh_rmc_init() fails with -ENOMEM,
the rmc pointer will be left as NULL but the interface is still
operational because ieee80211_mesh_init_sdata() is not allowed
to fail.
If this happens, we would blindly dereference rmc when checking
whether a multicast frame is in the cache. Instead just drop the
frames in the forwarding path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO
has a legacy client connected to it, it should disable P2P PS mechanisms.
Let the driver know about this with a new bss_conf parameter.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
